Comparison Hop-Sport HS-1016 vs Inter Atletika ST004

The type of bench / rack is indicated by the type of main exercises for which it is designed. In our time, among such shells, the following main types stand out: for bench press, for squats, for the press, for hyperextension and for biceps (bench press on Scott's desk). These types may well be combined in one model: for example, Scott benches are often an addition to the bench for the press and / or the press. Here are the main features of each option:

- For squats. Racks for safely performing barbell squats. As a rule, such simulators are used as auxiliary sports equipment with special stops to hold the neck and insure it from falling. Clamps under the bar in the design of the racks usually have a multi-stage adjustable height. Exercises with a projectile can be performed on squat racks without a safety net.

- For the bench. Designs designed primarily for working with a barbell - bench press from the chest and / or from the shoulders (see "Types of exercises"). The first option provides for the presence of a lying place, the second - a seated one, with back support; models that allow both uses usually use a tilt-adjustable backrest. In addition, there are bench press stands that do not have seats - they are designed for squats with a barbell.

- For the press. Designs for p...erforming twists on the press (see "Types of exercises"). At the heart of any such design is an incline bench with leg locks, on which the customer is placed at a negative angle in the initial position (head below legs). Some models have additional equipment that allows you to add weight when twisting.

- For Scott's press. One of the most popular biceps trainers. The main part of the Scott bench is an inclined stand, on which the athlete leans on the shoulder part of the arm (or both arms); and exercises on such a stand are flexion and extension of the arms with weights clenched in the fists. The key advantage of such a simulator is that the muscles of the shoulder girdle are practically excluded from work - the entire load is concentrated on the biceps, which allows you to effectively work it out.

- Hyperextension. A kind of “bench for the press back to front”: the customer lies on such a simulator with his back up, fixes his legs in special mounts, and the exercise itself consists in lifting the upper part of the body due to the muscles of the back. Accordingly, the main benefit of hyperextension is to strengthen the “muscular corset” of the back, which helps to maintain correct posture and prevent problems with the spine. However, with such exercises, some gluteal and femoral muscles are also pumped.

Types of incline angles available for the machine bench. Note that a specific angle of inclination can also be adjusted within the same type — for example, a bench with a negative angle can be made steeper or flatter.

— Positive. The angles of inclination are called positive, at which the upper part of the back (the side where the athlete's head is in the normal position) looks up. The exception is the vertical arrangement, which is specified separately. Simply put, this is the position of the back for being reclining on the simulator. This position is used in many types of exercises.

— Vertical. Strictly vertical position of the back. In most exercises where such a backrest is used, it is not necessary, however, additional support can provide comfort and increase the overall effectiveness of the exercise.

— Horizontal. The horizontal (for an athlete — lying) position is classic for the chest press (see "Types of exercises"), but can also be used in other types of training.

— Negative. The angle of inclination at which the head and torso of the athlete, when supported on the back, are directed downward; in other words, the angle at which the head is lower than in the horizontal position. This position is known to many primarily from twisting exercises — it allows you to provide a fairly intense...load on the press. However, its use is not limited to this: for example, some types of chest press also involve a low head position.

Types of exercises for which the simulator is designed.

Power benches and racks can be used for quite a wide variety of exercises: vertical pull, deadlift, waist row, pullover, chest press, shoulder press, barbell squat, arm curl, arm extension, flare, crunches, back extension, flexion / extension of the legs, push-ups (horizontal), push-ups (on uneven bars) and pull-ups. Here are the main features of each of these options:

- Vertical thrust. An exercise that imitates pull-ups on the horizontal bar: a seated athlete pulls down a bar loaded through a system of blocks. Such workouts are more flexible than traditional pull-ups, because. they allow you to vary the load in almost any range. The specific muscle groups involved can vary depending on the grip. On the other hand, vertical thrust requires rather complex equipment, which significantly affects the dimensions, weight and price of the entire structure. Therefore, th...is possibility is typical mainly for complex power simulators, and it is extremely rare in benches and racks.

- Deadlift. One of the fundamental, most famous and popular exercises for working with heavy weights. Initially performed with a barbell. The general essence of the exercise is to lift the weight from the floor to the level of the pelvis. There are several techniques for performing such traction, but in any case it is a complex exercise, it puts a load on most of the muscles of the body, and also has a noticeable developmental and strengthening effect on the body as a whole.

- Drawstring to the belt. Exercise for the muscles of the upper back, performed on a power bench. The pull to the belt can be performed with a barbell or dumbbell, standing in an inclined or horizontal position and resting your knee on the bench. The exercise strengthens the back, helps improve posture and arm strength.

— Pullover. Exercise, the basis of which is lifting the load from behind the head. One of the advantages of this technique is that it allows you to simultaneously work out three muscle groups at once: pectoral, lats and triceps. But the degree of load on each of these groups may be different, depending on the technique for performing pullovers. So, when performing an exercise lying on a horizontal bench, the triceps are mainly worked out, the pectoral muscles are less involved, and the lats do not strain at all to the degree necessary for training; to work out the latissimus dorsi, the position on an inclined bench is better with your head down, etc.

- Chest press. Bench press from the chest in a lying position - usually horizontal, allowing you to work out the triceps, pectoralis major and deltoid muscles. However, racks/bench benches may offer other variations of the bench press, for example, with a positive or negative angle (see "Bench angle"), which allows you to shift the load to the upper or lower chest, respectively.

- Shoulder press. An exercise that is kind of the opposite of pulling up: a barbell (or other load, such as dumbbells) needs to be “pushed” up from shoulder level. Promotes the development of the muscles of the shoulder girdle, in particular, the deltoid and trapezius. In fact, the shoulder press can be performed on any bench that allows you to sit securely with your back upright.

- Squats. Squats with holding on the shoulders of the bar, which plays the role of additional weights. Squats develop mainly the muscles of the thighs and buttocks; in general, this is one of the most important types of exercises not only in bodybuilding, but also in general training. To safely perform such exercises with a barbell, you need a barbell rack located at a high enough height so that the athlete can sit under it and take the barbell on his shoulders, straightening up. Such a rack is an indispensable element of equipment in simulators for squats with a barbell.

- Flexion of the arms. Exercise for bending the arms in the elbow joints. The main load in this case goes to the biceps and shoulder muscle; in addition, depending on the technique of execution, other muscles can be connected to the work. Arm curls can be performed on both press machines and Scott benches (see "Type").

- Extension of the arms. This category includes various exercises for the development of triceps. This can be either a French bench press (lifting weight from behind the head in a lying or semi-lying position), or other exercises in which the main load is provided by extending the arms.

- Breeding hands. In this case, as a rule, it means spreading the arms to the sides in a lying or sitting position, with weights. The main emphasis in the first case is on the pectoral muscles, however, certain types of lying arm extension are complex exercises that load a fairly extensive set of trunk muscles. The "sitting" version of the exercise is used to work out the deltoid muscles. For safety when breeding arms with weights, it is necessary to have a reliable foothold on the floor, which puts forward certain requirements for the height of the bench.

- Twisting. Standard exercises for the press; the ability to perform twists is mandatory for simulators of the corresponding type. The load is provided by bending in the back - raising the upper part of the torso towards the pelvis. Twisting can be performed both directly and with rotation, in the second case, the load on the oblique abdominal muscles increases. It is also possible to perform with weights, on some simulators, for the convenience of such work, special devices may be provided.

- Back extension. The standard type of exercise in training for hyperextension (see "Type"); in fact, the terms "hyperextension" and "back extension" are often used interchangeably. The exercise is a kind of opposite of twisting: the athlete is in a face down position, and the load is generated by lifting the torso back and up. In this case, the extensor muscles of the back, as well as the gluteal muscles and hip flexors, work primarily. The back extension is considered to be a fairly gentle and at the same time effective exercise, well suited even for people with no experience or with a weakened back.

- Flexion / extension of the legs. Exercises that work specific thigh muscles. Usually, in this case, the athlete sits on a bench, while the fixed pair of support-rollers is under the knees, and the movable one is above the ankles. The exercise itself is performed due to the work of the knee joints, weights are usually used.

- Push-ups (horizontal). Push-ups on weight with a horizontal position of the body. The support for the hands when performing such exercises is usually a pair of horizontal handles mounted on the same supports that play the role of a barbell rack (for more details, see "Push-up handles").

- Push-ups (on bars). In this case, push-ups are usually meant with an emphasis on two parallel handles, which are structurally similar to traditional gymnastic bars (for more details, see "Beams"). According to the execution technique, such exercises are similar to push-ups on the uneven bars, and the main study in them goes to the triceps and pectoral muscles.

- Pull-ups. Classic pull-ups on the horizontal bar (see above). The load goes both on a number of arm muscles (biceps, forearms), and on the latissimus dorsi; while the ratio of the load on different muscle groups will depend on the grip used. It is worth noting here that in some power benches and racks, the horizontal bar looks like a pair of separate handles and allows you to pull up only with a wide grip, when the main load goes to your back. In other models, a full-fledged crossbar may also be provided, allowing the use of other types of grip, and sometimes supplemented with perpendicular handles.

Country of origin of the brand under which the simulator is presented on the market. It usually refers to the country in which the brand was originally registered, or in which the company's headquarters are located. By this parameter, the overall quality of the simulator and the brand as a whole is often assessed, however, such assessments are rather conditional. Thus, the "homeland" of the brand often does not coincide with the place of actual production: many large firms use factories in regions with cheap labor to reduce costs. At the same time, the actual quality depends not so much on the country of production, but on how carefully the manufacturer monitors its reputation and controls the goods leaving the factories. In addition, companies that actually originate from one state may register brands in another in order to look more prestigious in the eyes of the manufacturer. All this makes national stereotypes not particularly relevant in the modern world; Simply put, it is worth looking not so much at the origin of a particular brand, but at its overall reputation.

The dimensions of the equipment in the assembled and ready to work state. It is important to note that in fact more space is needed for comfortable and proper operation of the simulator. This is due to the need to have space for the person himself, the removal of arms and legs when performing exercises and using additional equipment. If we are talking about a gym, then people working nearby or placed equipment, etc., can become a hindrance. Therefore, it is recommended when choosing to calculate that in addition to the dimensions of the simulator, you may need an additional metre of free space on each side.