Electrical Wires & Cables

Male Terminal Adapters are connectors used to transition from a spigot end PVC conduit to a threaded metal or PVC plastic female bell end. Male Terminal Adapters can also be used to connect PVC conduit to a box or other threaded body with use of a lock nut. The fittings consist of one solvent weld female end and one threaded male end. Both ends will fit the same diameter conduit.

For connecting different sizes of PVC conduit, also for non-metallic schedule 40 conduit. Non-conductive, will not rust or corrode. Joins 3/4 in. PVC conduit to 1/2 in. PVC conduit.

The Sigma ProConnex Reducing Washers are used to decrease the size of a knockout in a steel outlet box or metal enclosure. Two of these zinc-plated steel reducing washers are required for each knockout. They are embossed for self-centering and easy installation.

Square blank cover is used with 4 in. square boxes to mount switches, receptacles, and devices. It is built with angled slots on the covers to compensate for up to 1/2 in. of box misalignment on upright framing members. It is made of zinc-plated steel for durability.

Handy box cover used to close a 4in x 2in. handy box. It is also designed to attach devices in a surface-mount industrial or commercial setting. The captive cover screws provide a straightforward installation. Additionally, the zinc-plated steel provides durability for the long term.

The Sigma ProConnex Snap Lock NM Clamp Type Cable Connectors are used to terminate NM cable or flexible cord to a 1/2-inch knockout in a dry location box or enclosure. The Snap Lock design requires no tools when attaching to the box for faster installation. These connectors are of die-cast zinc and spring steel construction.

Square blank covers are used to hang commercial or industrial lighting fixtures, security cameras, motion detectors, occupancy sensors, and other electronic devices for overhead ceiling installations. This box cover is a great fit for commercial or industrial applications. Additionally, is ideal for locations where the pipe stem or fixture is not subjected to motion or vibration.

Adapter used with the hub inside a box or enclosure. The cylinder protrudes through a hole in the box wall and is solvent welded to a female fitting outside the box or enclosure.

The Sigma ProConnex Conduit Locknuts are used for securing Rigid conduit, IMC and other threaded connectors to a steel outlet box or metal enclosure. These zinc-plated steel locknuts are recommended for indoor applications.

The Octagon Flat Blank Cover is used to close off a 4 in. octagon box as a junction box, add a wiring device, or mount a light fixture. This cover features keyhole mounting holes for easy installation. It provides a convenient way to cover or terminate exposed electrical wire. Additionally, this cover is both UL and RoHS compliant for safe use.

The Sigma ProConnex Plastic Insulating Bushings are used on the end of Rigid conduit, IMC and other threaded connectors to provide a smooth well rounded bearing surface to protect wires or cables when pulling. These non-metallic bushings are rated for 105C and flame retardant.

A section of PVC Schedule 40 conduit which as been heated and bent to effect a 90 degree change in direction in a conduit run. Both ends of the bend are spigot (plain) end. Both ends are solvent weld. Can be used above ground or buried and are suitable for concrete encasement.

The Sigma ProConnex knockout seals are used to close exposed holes in an outlet box or metal enclosure. These knock-out seals are of zinc-plated steel construction.

Handy box cover used to close a 4in x 2in. handy box. It is also designed to attach devices in a surface-mount industrial or commercial setting. The captive cover screws provide a straightforward installation. Additionally, the zinc-plated steel provides durability for the long term.

The Sigma ProConnex Conduit Nipples are used in conjunction with locknuts to provide a short raceway between two outlet boxes or metal enclosures.

Threaded closure plugs are used to seal off unused outlets. Plugs are for use with Weatherproof boxes. They are also for use with extension adapters and cluster covers.

Cantex EZ20SNW EZ Box is a 20.3 cu. in. 1-gang electrical switch and outlet box for residential or light commercial electrical installations. It features knockouts and enhanced angled nails for easy installation.

Adapter used with the hub inside a box or enclosure. The cylinder protrudes through a hole in the box wall and is solvent welded to a female fitting outside the box or enclosure.

Switch box supports are used to secure a switch box in a hollow wall cavity of drywall or plaster. It can be used with any deep switch box that has ears. Available in two lengths, they provide options for both shallow and deep switch boxes.

The Sigma ProConnex Squeeze Connectors are used to terminate AC, MC or FMC/RWFMC to a knockout in a dry location box or enclosure. These die-cast zinc connectors are equipped with a tri-combo screw and are suitable for aluminum or steel cable and conduit.

The brand for this item is MAXXIMA Orders $75 or more ship free This item ships directly from Zoro

The Sigma ProConnex Reducing Bushings are used to decrease the entry size of threaded conduit to join conduits of two different sizes. These reducing bushings are of zinc die-cast construction.

SimPush, push-to-install conduit couplings are used to secure two ends of EMT conduit together quickly and without tools. These EMT fittings are designed for use in dry locations only.

Cantex 5140106 is a 1-1/4 in. Male terminal adapter which is a connector used to transition from a spigot end PVC conduit to a threaded metal or PVC plastic female bell end.