Electrical Wires & Cables

It is ideally used for fire resistive walls and ceilings in new work residential construction. Switch or receptacle outlet box is UL listed. Machine tapped device holes, offset gauge marks, leveling ribs, rigid hard box construction, no distortion with high temperatures, shatter resistant with low temperatures.

Others

Sigma's Safety Nail Plates are used to protect cable insulation from nail punctures in wooden structures. These nail plates are of zinc-plated steel construction.

Innovative, interlocking design of this cable protector plate does not allow nail or screw penetration through gaps or holes. No additional hardware needed, just position and hammer down spurs.

The Sigma ProConnex AC/MC Connectors are used to terminate AC or MC cable to a knockout in a dry location box or enclosure. These die-cast connectors are equipped with a tri-combo screw and are suitable for aluminum or steel conduit.

Adapter used with the hub inside a box or enclosure. The cylinder protrudes through a hole in the box wall and is solvent welded to a female fitting outside the box or enclosure.

The brand for this item is ZORO SELECT Orders $75 or more ship free This item ships directly from Zoro

The Sigma ProConnex Snap Lock Screw-In Connectors are used to terminate FMC to a knockout in a dry location box or enclosure. The Snap Lock design requires no locknut when attaching to the box for faster installation. These connectors are suitable for aluminum or steel cable and conduit. They are of die-cast zinc and spring steel construction. *

The Sigma ProConnex knockout seals are used to close exposed holes in an outlet box or metal enclosure. These knock-out seals are of zinc-plated steel construction.

The Sigma ProConnex Clamp Type Combination Connectors are used to terminate AC, MC or FMC to a knockout in a dry box or enclosure. These die-cast zinc connectors are equipped with tri-combo screws and are suitable for aluminum or steel cable and conduit.

The Sigma ProConnex Snap Lock NM Clamp Type Cable Connectors are used to terminate NM cable or flexible cord to a 1/2-inch knockout in a dry location box or enclosure. The Snap Lock design requires no tools when attaching to the box for faster installation. These connectors are of die-cast zinc and spring steel construction.

Male Terminal Adapters are connectors used to transition from a spigot end PVC conduit to a threaded metal or PVC plastic female bell end. Male Terminal Adapters can also be used to connect PVC conduit to a box or other threaded body with use of a lock nut. The fittings consist of one solvent weld female end and one threaded male end. Both ends will fit the same diameter conduit.

The Sigma ProConnex Reducing Washers are used to decrease the size of a knockout in a steel outlet box or metal enclosure. Two of these zinc-plated steel reducing washers are required for each knockout. They are embossed for self-centering and easy installation.

The Sigma ProConnex Conduit Locknuts are used for securing Rigid conduit, IMC and other threaded connectors to a steel outlet box or metal enclosure. These zinc-plated steel locknuts are recommended for indoor applications.

The Sigma ProConnex Plastic NM Cable Connectors are used to terminate NM Sheathed Cable to a 3/4-in knockout in a dry location box or enclosure. This snap-in design provides easy installation for a wide variety of cable configurations.

A section of PVC Schedule 40 conduit which as been heated and bent to effect a 90 degree change in direction in a conduit run. Both ends of the bend are spigot (plain) end. Both ends are solvent weld. Can be used above ground or buried and are suitable for concrete encasement.

The Sigma ProConnex Reducing Washers are used to decrease the size of a knockout in a steel outlet box or metal enclosure. Two of these zinc-plated steel reducing washers are required for each knockout. They are embossed for self-centering and easy installation.

The brand for this item is ZORO SELECT Orders $75 or more ship free This item ships directly from Zoro

Square blank covers are used to hang commercial or industrial lighting fixtures, security cameras, motion detectors, occupancy sensors, and other electronic devices for overhead ceiling installations. This box cover is a great fit for commercial or industrial applications. Additionally, is ideal for locations where the pipe stem or fixture is not subjected to motion or vibration.

The Sigma ProConnex knockout seals are used to close exposed holes in an outlet box or metal enclosure. These knock-out seals are of zinc-plated steel construction.

Dependable and easy to use, Gardner Bender terminals (and wiring accessories) offer the high quality and application flexibility that professionals demand. Available in a variety of packaging options, look to Gardner Bender for secure wire connection option.

Cantex EZ20SNW EZ Box is a 20.3 cu. in. 1-gang electrical switch and outlet box for residential or light commercial electrical installations. It features knockouts and enhanced angled nails for easy installation.

Adapter used with the hub inside a box or enclosure. The cylinder protrudes through a hole in the box wall and is solvent welded to a female fitting outside the box or enclosure.

The Sigma ProConnex Squeeze Connectors are used to terminate AC, MC or FMC/RWFMC to a knockout in a dry location box or enclosure. These die-cast zinc connectors are equipped with a tri-combo screw and are suitable for aluminum or steel cable and conduit.