Vacuum Cleaner Accessories

Foam Filter in Yellow for Select BISSELL Upright Vacuum Cleaners. This filter is washable. Wash in warm water and mild detergent and allow it to completely air dry prior to next use of the vacuum. It more→is recommended to change with new filters every 6 to 8 months depending on use and how often the filter is cleaned. Dirty filters will restrict the air flow and reduce suction. Keeping a clean filter will keep suction levels at optimal levels. | Foam Filter for Select Vacuums | 1610289

Old Part Number 160-6285. Fits the 1576 Series and 1683 Series machines. | Foam Filter for Super Light Stick Vacuums | 1607642

Mesh Filter Frame for Select Canister Vacuums, including OptiClean Canister Vacuum, Model 1989D. This Mesh Filter Frame is part of the Cyclone System that sits within the dirt tank. This mesh filter c more→an be rinsed off when dirty, but must be completely dry prior to next use. | Mesh Filter Frame for Select Canister Vacuums | 1613429

3-pack of foam filters for the BISSELL ICONpet Robotic Vacuum To clean and maintain the filter follow these directions: Remove the Dirt Bin. Pinch and pull filter assembly out from the back of the Dir more→t Bin. Clean filter if dirty. Replace if damaged. Separate washable filter from assembly. Wash filter and filter assembly. Let dry completely before reassembling. Open Dirt Bin, clean debris surrounding Separator Cone. If necessary, carefully twist cone and pull up to remove. | Foam Filter (3-pack) ICONpet Robotic Vacuum | 1618610

Mesh Filter Screen holds the filter for Select Stick Vacuums including Adapt Ion and PowerLifter Ion Stick Vacs, Series 2286, 2482. To clean the Filter & Screen follow these instructions: Turn the pow more→er OFF and remove the Dirt Tank Grasp filter tabs and lift up to remove the washable filter assembly from the Dirt Cup Grip the filter assembly and turn counter-clockwise and lift down to remove filter from filter screen Tap against the inside of a waste container, removing any visible dirt Replace filter back in the filter screen then turn clockwise to lock into place Attach filter assembly back into the dirt tank and attach to hand vacuum until it snaps securely in place. NOTE: You may rinse

Foam Filter with the Frame for Select Canister Vacuum Cleaners including PowerClean and MultiClean Wet/Dry Canister Vacuums, Series 2035. | Foam Filter with Frame for Select Canister Vacuums | 1613118

Flat Pump Belt for Select BISSELL Carpet Cleaners, including BISSELL PowerForce PowerBrush Pet XL Carpet Cleaner, series 3071. Follow these instructions on replacing the Belts and Brush Rolls. Unplug more→the machine. Remove both tanks. With the machine reclined, locate the belt access cover and lay the machine on its side. Remove the 3 screws on the brush access cover using a Phillips-head screwdriver. Remove the access cover to expose the cogged belt and brush roll. Remove the 2 screws on the belt access cover using a Phillips-head screwdriver. Remove the access plate to expose the flat pump belt. If flat pump belt is broken, you may gently remove it from the machine. We will replace this belt

This filter fits Series 2043 PowerGlide Lift-Off Vacuums with a Serial Number of 19076 and PRIOR. Replacement filter pack comes with 4 filters: 1 - Pre-motor Foam Filter 1 - Post-motor Pleated Media F more→ilter 1 - Pre-motor Fiber Filter (Fits Models 2763 & 9182) 1 - Pre-motor Fiber Filter (Fits Models 1305 & 1306) Foam filters are washable with mild soap and water. Air dry completely before reinstalling. Do not wash the square allergen media filter. | Replacement Filter Pack for Powerglide Vacuum Cleaners | 12118

Genuine BISSELL Belt - Pump Belt for PowerLifter, ProHeat and PowerSteamer Upright Deep Cleaner Series. You should check your machines rotating floor brush and drive belt regularly for wear or damage. more→Replace the belt if it is broken or worn. The drive belt is a critical component of your vacuum that allows the brush roll to rotate and remove deep down dirt from your carpets. The pump belt is located below the belt access door on the side of your machine. The pump belt connects to the motor shaft. Remove the worn or broken belt and loop the new pump belt around the red pulley end of the pump pulley. Stretch the new pump belt up and around the silver motor shaft. If your machine is not

Aluminum Upper Handle Assembly for the AirRam Cordless Vacuum. | Aluminum Handle Assembly for AirRam Cordless Vacuum | 1610316

Connects the pump to the motor shaft. For machines with serial numbers BEFORE 18167FXB. | Flat Pump Belt for Select Upright Carpet Cleaners | 1606428

Flat Pump Belt for Select Upright Carpet Cleaners for machines with Serial Numbers AFTER 18167FXB | Flat Pump Belt for Select Upright Carpet Cleaners | 1616370

Fits ProLite Models | Dirt Bin and Debris Door Assembly for Prolite Vacuums | 2032095

Dirt Bin Assembly for the AirRam Cordless Vacuum Cleaner. | Dirt Bin Assembly for AirRam Cordless Vacuum | 1610313

Dirt Tank Assembly for select BISSELL Robotic Vacuums including EV675 Multi-Surface Robotic Vacuum Cleaner, series 2503 and CleanView Connect Robotic Vacuum, Series 2933. To clean the dirt tank assemb more→ly follow these directions: Press the button on top of the dirt bin and pull to remove. Open filter door by pulling both sides apart Empty the debris from the dirt bin Remove the filter cover, followed by the Foam and Pleated Filters. Use the cleaning tool to brush the filter cover and filters. DO NOT WASH THE FILTERS With filters removed, rinse the dirt bin with tap water. Ensure dirt bin is completely dry before re-installing. It is not necessary to wash every time. DO NOT MACHINE WASH THE

Replacement Dirt Bin Assembly for the BISSELL ICONpet Robotic Vacuum Cleaner. To Empty the Dirt Bin, follow these instructions: Remove the Dirt Bin from the robot by pulling up on the handle as shown. more→Press button to release Dirt Bin Lid and empty into trash. Close the lid until it clicks shut. Put Dirt Bin back in the Robot. | Dirt Bin Assembly ICONpet Robotic Vacuum | 1618607

Dirt Cup Bottom Lid Gasket seals the bottom lid to the Dirt Tank for no air leaks. Located on the Tank Lid in black. | Dust Bin Bottom Lid Gasket for Pet Hair Eraser Vacuum | 1608830

Tank Handle Assembly fits the PowerLifter Rewind 1792 Series. | Tank Handle Assembly for PowerLifter Vacuum | 1610211

Handle for the Hard Floor Expert Canister Vacuums - Model 1547. | Loop Handle for Hard Floor Expert Canister Vacuum | 1607391

Tank Handle Assembly for the PowerLifter Vacuum - 1793 Series. | Tank Handle - Purple for PowerLifter Vacuum | 1610210

Tank handle for the Deep Clean Premier Series Upright Carpet Cleaning Machines. Fits on the Tank Lid Assembly. Comes in black. | Tank Handle for Premier Series Upright Carpet Cleaners | 1600086

This filter can be used in place of part number 60461. Genuine BISSELL Filter - Inner/Outer Circular filter assembly: includes 1 Inner Pleated Filter and 1 Outer Foam Filter. This filter fits into the more→Dirtcup of the Easy Vac Series and PowerForce Compact Series Vacuums. It is recommended to clean or replace your filters every 3-6 months depending on use. The outer foam filter is washable clean by hand washing in warm water. A mild detergent may be used if desired. Allow the filter to air dry completely before replacing. Its a good idea to buy an extra filter to always have a dry one ready to use! Did you know that your vacuum, bagless or bagged, has filters that should be checked