Comparison A-Data XPG GAMMIX S50 LITE AGAMMIXS50L-1T-C 1 TB vs A-Data XPG GAMMIX S11 Pro M.2 AGAMMIXS11P-1TT-C 1.02 TB

Nominal drive capacity. This parameter directly determines not only the amount of data that can fit on the device, but also its cost; many SSD models even come in several versions that differ in capacity. Therefore, when choosing, it is worth considering the real needs and features of the application — otherwise you can overpay a significant amount for volumes that are not needed in fact.

In terms of actual values, a capacity of 120 GB or less is considered small these days. This can also be equated with a 240 GB SSD. Average values are already considered 500 GB, increased — 1 TB(in the range of which SSDs fall 400 and 800 GB). And the most capacious modern SSDs can accommodate 2 TB, 4 TB and even more.

Connection interface supported by an M.2 drive (see Form Factor).

All such drives use a standard hardware connector, however, different electrical (logical) interfaces can be implemented through this connector — either SATA (usually SATA 3), or PCI-E (most often in PCI-E 3.0 2x, PCI-E 3.0 4x, PCI-E 4.0 4x, PCI-E 5.0 4x). The M.2 connector on the motherboard must support the appropriate interface — otherwise the normal operation of the SSD will not be possible. Let's consider each option in more detail.

SATA 3 connectivity provides data transfer rates up to 5.9 Gbps (approx. 600 Mbps); it is considered a very simple option and is used mainly in low-cost M.2 modules. This is due to the fact that this interface was originally created for hard drives, and for faster SSD drives, its capabilities may no longer be enough.

In turn, the PCI-E interface provides higher connection speeds and allows the implementation of special technologies like NVMe (see below). The designation of such an interface indicates its version and the number of lines – for example, PCI-E 3.0 2x means version 3 with two data lines. By this designation you can determine the maximum connection speed: PCI-E version 3.0 gives just under 1 GBps per line, version 4.0 – twice as much (up to 2 GBps), 5.0 – twice as much a...s the “four” (almost 4 GBps). Thus, for example, for PCI-E 5.0 4x the maximum data transfer speed will be about 15 GBps (4 lanes of almost 4 GBps). However, we note that newer and faster drives can be connected to earlier and slower M.2 connectors – except that the data transfer speed will be limited by the capabilities of the connector.

Model of the controller installed in the SSD.

The controller is a control circuit, which, in fact, ensures the exchange of information between the memory cells and the computer to which the drive is connected. The capabilities of a particular SSD module (in particular, read and write speed) largely depend on this particular scheme. Knowing the controller model, you can find detailed data on it and evaluate the capabilities of the drive. For simple everyday use, this information is usually not needed, but for professionals and enthusiasts (modders, overclockers) it can come in handy.

Nowadays, high-end controllers are produced mainly under such brands: InnoGrit, Maxio, Phison, Realtek, Silicon Motion, Samsung.

The highest speed in write mode characterizes the speed with which the module can receive information from a connected computer (or other external device). This speed is limited both by the connection interface (see "Connector"), and by the characteristics of the device of the SSD itself.

The highest data exchange rate with a computer (or other external device) that the drive can provide in read mode; in other words — the highest speed of information output from the drive to an external device. This speed is limited both by the connection interface (see "Connector"), and by the characteristics of the device of the SSD itself. Its values can vary from 100 – 500 MB / s in the slowest models to 3 Gb / s and higher in the most advanced ones.

The IOPS provided by the drive in write mode.

The term IOPS refers to the highest number of I / O operations that an SSD module can perform per second, in this case, when writing data. By this indicator, the speed of the drive is often evaluated; however, this is not always true. Firstly, the IOPS values of different manufacturers can be measured in different ways — by the maximum value, by average, by random write, by sequential write, etc. Secondly, the benefits of high IOPS become noticeable only with some specific operations — in in particular, the simultaneous copying of numerous files. In addition, in fact, the speed of the drive may be limited by the system to which it is connected. In light of all this, it is generally acceptable to compare different SSD modules by IOPS, but the real difference in performance is likely not to be as noticeable as the difference in numbers.

As for specific values, for the write mode with IOPS up to 50K is considered relatively modest, 50 – 100K — medium, more than 100K — high.

The IOPS provided by the drive in read mode.

The term IOPS refers to the maximum number of I / O operations that an SSD module can perform per second, in this case, when reading data from it. By this indicator, the speed of the drive is often evaluated; however, this is not always true. Firstly, the IOPS values of different manufacturers can be measured in different ways — by the maximum value, by the average, etc. Secondly, the advantages of high IOPS become noticeable only with some specific operations — in particular, when copying numerous files at the same time. In addition, in fact, the speed of the drive may be limited by the system to which it is connected. In light of all this, it is generally acceptable to compare different SSD modules by IOPS, but the real difference in performance is likely not to be as noticeable as the difference in numbers.

For modern SSDs in read mode, an IOPS value of less than 50K is considered a very limited indicator, in most models this parameter lies in the range of 50 – 100K, but there are also higher numbers.

The abbreviation TBW stands for drive time between failures, expressed in terabytes. In other words, this is the total amount of information that is guaranteed to be written (rewritten) to this module. This metric measures the overall reliability and lifespan of a drive—the higher the TBW, the longer the device will last, all other things being equal.

Note that knowing the TBW and the warranty period, you can calculate the number of rewrites per day (DWPD, see the relevant paragraph), if the manufacturer did not specify these data. To do this, use the formula: DWPD = TBW / (V * T * 365), where V is the drive capacity in terabytes, T is the warranty period (years). As for specific numbers, there are a lot of drives on the market with a relatively low TBW — up to 100 TB ; even these values are often sufficient for everyday use for a considerable amount of time. However, models with TBW at the level of 100 – 500 TB are more common. Values of 500 – 1000 TB can be classified as "above average", and in the most reliable solutions this figure is even higher.

Module support for the TRIM command.

A feature of the operation of SSD modules is that when deleting data in the normal mode (without using TRIM), changes are made only to the “table of contents” of the drive: certain cells are marked as empty and ready for new information to be written. However, the old information is not deleted from them, and when writing new data, you actually have to overwrite it — this significantly slows down the speed of work. The TRIM command is designed to correct the situation: when it arrives, the drive controller checks if the cells marked as empty are empty and cleans them if necessary.

Of course, this function must be supported not only by the drive, but also by the system, however, the ability to work with TRIM is built into most popular modern operating systems.