Comparison Samsung 970 EVO M.2 MZ-V7E500BW 500 GB vs Samsung 860 EVO M.2 MZ-N6E500BW 500 GB

Connection interface supported by an M.2 drive (see Form Factor).

All such drives use a standard hardware connector, however, different electrical (logical) interfaces can be implemented through this connector — either SATA (usually SATA 3), or PCI-E (most often in PCI-E 3.0 2x, PCI-E 3.0 4x, PCI-E 4.0 4x, PCI-E 5.0 4x). The M.2 connector on the motherboard must support the appropriate interface — otherwise the normal operation of the SSD will not be possible. Let's consider each option in more detail.

SATA 3 connectivity provides data transfer rates up to 5.9 Gbps (approx. 600 Mbps); it is considered a very simple option and is used mainly in low-cost M.2 modules. This is due to the fact that this interface was originally created for hard drives, and for faster SSD drives, its capabilities may no longer be enough.

In turn, the PCI-E interface provides higher connection speeds and allows the implementation of special technologies like NVMe (see below). The designation of such an interface indicates its version and the number of lines – for example, PCI-E 3.0 2x means version 3 with two data lines. By this designation you can determine the maximum connection speed: PCI-E version 3.0 gives just under 1 GBps per line, version 4.0 – twice as much (up to 2 GBps), 5.0 – twice as much a...s the “four” (almost 4 GBps). Thus, for example, for PCI-E 5.0 4x the maximum data transfer speed will be about 15 GBps (4 lanes of almost 4 GBps). However, we note that newer and faster drives can be connected to earlier and slower M.2 connectors – except that the data transfer speed will be limited by the capabilities of the connector.

Model of the controller installed in the SSD.

The controller is a control circuit, which, in fact, ensures the exchange of information between the memory cells and the computer to which the drive is connected. The capabilities of a particular SSD module (in particular, read and write speed) largely depend on this particular scheme. Knowing the controller model, you can find detailed data on it and evaluate the capabilities of the drive. For simple everyday use, this information is usually not needed, but for professionals and enthusiasts (modders, overclockers) it can come in handy.

Nowadays, high-end controllers are produced mainly under such brands: InnoGrit, Maxio, Phison, Realtek, Silicon Motion, Samsung.

NVMe drive support.

NVMe is a communication protocol designed specifically for SSD modules and used when connected via the PCI-E bus. This protocol was developed to eliminate the shortcomings of earlier connection standards (like SCSI or SATA) — primarily low speed, which did not allow realizing the full capabilities of solid-state memory. NVMe takes into account the key advantages of SSD — independent access, multithreading and low latency. Support for this protocol is built into all major modern operating systems; it works not only through the original PCIe interface, but also through M.2 (see Form Factor). And the U.2 connector was generally created specifically for NVMe SSDs (although the presence of this connector in itself does not mean compatibility with this protocol).

The highest speed in write mode characterizes the speed with which the module can receive information from a connected computer (or other external device). This speed is limited both by the connection interface (see "Connector"), and by the characteristics of the device of the SSD itself.

The highest data exchange rate with a computer (or other external device) that the drive can provide in read mode; in other words — the highest speed of information output from the drive to an external device. This speed is limited both by the connection interface (see "Connector"), and by the characteristics of the device of the SSD itself. Its values can vary from 100 – 500 MB / s in the slowest models to 3 Gb / s and higher in the most advanced ones.

The IOPS provided by the drive in write mode.

The term IOPS refers to the highest number of I / O operations that an SSD module can perform per second, in this case, when writing data. By this indicator, the speed of the drive is often evaluated; however, this is not always true. Firstly, the IOPS values of different manufacturers can be measured in different ways — by the maximum value, by average, by random write, by sequential write, etc. Secondly, the benefits of high IOPS become noticeable only with some specific operations — in in particular, the simultaneous copying of numerous files. In addition, in fact, the speed of the drive may be limited by the system to which it is connected. In light of all this, it is generally acceptable to compare different SSD modules by IOPS, but the real difference in performance is likely not to be as noticeable as the difference in numbers.

As for specific values, for the write mode with IOPS up to 50K is considered relatively modest, 50 – 100K — medium, more than 100K — high.

The IOPS provided by the drive in read mode.

The term IOPS refers to the maximum number of I / O operations that an SSD module can perform per second, in this case, when reading data from it. By this indicator, the speed of the drive is often evaluated; however, this is not always true. Firstly, the IOPS values of different manufacturers can be measured in different ways — by the maximum value, by the average, etc. Secondly, the advantages of high IOPS become noticeable only with some specific operations — in particular, when copying numerous files at the same time. In addition, in fact, the speed of the drive may be limited by the system to which it is connected. In light of all this, it is generally acceptable to compare different SSD modules by IOPS, but the real difference in performance is likely not to be as noticeable as the difference in numbers.

For modern SSDs in read mode, an IOPS value of less than 50K is considered a very limited indicator, in most models this parameter lies in the range of 50 – 100K, but there are also higher numbers.