Comparison Onkyo TX-SR444 vs Yamaha RX-V575

Possibility to simulate multi-channel (for example, 5.1) sound in traditional two-channel headphones. For this, a Dolby Headphone decoder is usually used, which processes the sound in such a way that the sound heard in the headphones is perceived as multi-channel — in particular, the intended position of its sources can be determined much more accurately. And considering that modern Hi-Fi class headphones are not inferior in sound quality to acoustics (and are significantly cheaper), this feature may well come in handy even for demanding audiophiles.

the maximum sound power that can be delivered by the power amplifier (if the receiver has one, see "Type") per speaker channel. It is worth noting here that in this case it is customary to indicate the so-called RMS (Rated Maximum Sinusoidal), or rated power. Rated is considered the highest power that the amplifier is guaranteed to be able to produce without interruption for an hour without any failures or breakdowns. Short-term jumps in the signal level can significantly exceed this value, but the main indicator is still the rated power.

The power of the amplifier largely determines the sound volume of the speaker system connected to the device. In fact, the loudness also depends on the characteristics of the speakers — sensitivity, impedance, etc.; however, other things being equal, the same acoustics on a more powerful amplifier will sound louder. In addition, this parameter also affects the compatibility of the speakers and the amplifier — it is believed that the difference in the nominal powers of these components should not exceed 10-15% (and ideally, the powers should generally match). And since different rooms require speakers of different power, this also affects the choice of amplifier for a particular environment; specific recommendations on the ratio of room characteristics and acoustic power can be found in special sources.

Also note that if the amplifier can operate with a load of different resistance (see..."Permissible acoustic impedance"), then for different options the power per channel will be different — the lower the resistance, the higher the power. In the characteristics, in this case, the maximum value of this parameter is usually indicated — that is, the power at the minimum allowable resistance.

— AM/FM radio. The presence of a built-in tuner that allows you to receive AM and FM radio broadcasts without additional devices (except perhaps an antenna is required, and then not always). In FM, it is possible to realize the transmission of high-quality stereo sound, however, the waves propagate only within the line of sight (10-20 km); therefore, most of the stations in this range are classified as "urban music". In AM, the transmission range is already measured in hundreds of kilometers, but the sound quality is noticeably lower; therefore, such stations usually specialize in talk programs (particularly news).

— USB stick. The ability to connect a USB drive to the receiver — for example, a "flash drive" or an external hard drive — and play content from it directly. This requires a USB connector. Most often, in models with this function, it is located on the front panel (see below) — this provides ease of connection; at the same time, there are exceptions. Also note that the very presence of USB does not necessarily imply the possibility of playing from external media — this interface can be used for service purposes, for example, to update the firmware or play from a PC (see "Advanced (inputs) — USB Type B").

— Network audio streaming. The ability to play streaming audio over a local network or the Internet (including from services like Grooveshark o...r Last.Fm). The name "streaming" is due to the fact that each song is played directly from the network, without being written to the receiver's own permanent storage. This function, by definition, requires connection to computer networks; most often, a Wi-Fi module is used for this purpose (see "Interfaces") or a LAN connector.

— Internet radio. The ability to use the receiver to receive and play Internet radio broadcasts. This feature is similar in many ways to the network audio described above — in particular, it requires a network connection to work, and the data is streamed; however, in the case of network audio, the user himself chooses what and when to listen, here the broadcast is similar to conventional radio transmissions and is controlled from the radio station. Actually, many major stations broadcast their programs not only on the traditional air, but also via the Internet; There are also specialized projects broadcasting only on the Web. In general, the choice of programs is much more extensive than for conventional radio broadcasting — after all, Internet radio has no range restrictions. And the receivers themselves may provide additional tools for managing such broadcasting — for example, catalogs, search by genres, languages, etc.

- AirPlay. Technology for transmitting multimedia data via a wireless connection ( Wi-Fi). Developed by Apple, it is intended mainly for broadcasting content from various Apple devices (primarily portable gadgets) to compatible external devices. Allows you to transfer audio files (in audio streaming mode, see “Tuner and playback” for more details), as well as images, text data and even video. The presence of AirPlay in the receiver will allow you to connect Apple equipment with support for this technology to it for direct playback, as well as display information about files on an external screen (for example, a TV) - song name, artist name, etc.

- AirPlay 2. The second version of the AirPlay technology described above, released in 2018. One of the main innovations introduced in this update was support for the multi-room format - the ability to simultaneously broadcast several separate audio signals to different compatible devices installed in different locations. Thus, you can, for example, turn on the next episode of your favorite series from your iPhone on the TV in the living room, and relaxing music from your iPod in the kitchen, etc. In addition, AirPlay 2 received a number of other improvements - improved buffering, the ability to stream to stereo acoustics, as well as support for voice control via Siri.

- Chromecast.... Original name: Google Cast. Technology for broadcasting content to external devices, developed by Google. Allows you to transmit video and audio from a PC or mobile device to the AV receiver; broadcasting is usually carried out via Wi-Fi, while the receiver and the signal source must be on the same Wi-Fi network (with the exception of Chromecast media players). Chromecast technology supports two modes - actual broadcasting through special applications (available for Windows, macOS, Android and iOS) and “mirroring” content opened in the Google Chrome browser on an external screen.

- Wi-Fi. A wireless interface used primarily for building computer networks. Accordingly, AV receivers may need its presence primarily to implement network functions - streaming audio, Internet radio (see “Tuner and playback”), AirPlay (see above), DLNA (see below). Connecting to computer networks can also be done through a wired LAN interface(see below), but Wi-Fi is more convenient due to the absence of wires and the ability to work through obstacles (including walls) at a distance of several tens of meters. In addition, in some models, this technology can also be used to communicate directly with other devices - for example, to use a smartphone or tablet as a remote control, or to broadcast live video using Miracast technology or another similar format.

— Bluetooth. Direct wireless communication technology between various electronic devices; operates at a range of about 10 m, although some specific operating formats provide a longer range. Technically, it can be used for different purposes, depending on the protocols supported by a particular device; In AV receivers, two protocols are most often found - A2DP for wireless broadcasting of audio signals and AVRCP for remote control. In the first case, we are usually talking about transmitting a signal from an external device (smartphone, laptop, etc.) to the receiver; theoretically, the opposite option is also possible - broadcasting sound to Bluetooth headphones or acoustics, however, for a number of reasons, this format of operation is almost never found in AV receivers. AVRCP, in turn, allows you to use an external gadget (for example, the same smartphone) as a remote control.

- LAN. A standard interface for wired connection of various equipment (including AV receivers) to computer networks, incl. to access the Internet. Due to the presence of a wire, it is less convenient to connect than the Wi-Fi described above. On the other hand, a LAN connection wins in terms of connection reliability and actual data transfer speed - especially if there are many wireless devices on the network and Wi-Fi channels are busy (which is often the case, since Wi-Fi modules are very popular in modern electronics ). Therefore, for working with large volumes of data - for example, watching high-definition video via DLNA (see below) - LAN is better suited.

— RS-232. A wired interface that originally appeared in computer technology. In AV receivers, it can be called a service connector: content is not transmitted through this connector, but through it you can connect the device to a computer and remotely change settings, as well as update the firmware.

— MHL. High-speed wired interface for transmitting multimedia data (video and audio) from mobile devices to external screens. The bandwidth allows you to work with high or even ultra-high resolution images, as well as multi-channel audio. Also, when connected, the gadget can be charged. In mobile devices, the MHL signal is output via a standard microUSB port; and the role of the input in AV receivers (and other stationary equipment) is played by the HDMI connector (see below) - however, not every connector, but only one that is initially compatible with MHL and has the appropriate marking. Adapters are available for connecting to regular HDMI, but additional functions (like charging) may not be available with this connection.

- DLNA. A technology used to connect various electronic devices into a single digital network with the ability to directly exchange content. Devices for which support for this standard is declared are able to communicate effectively regardless of the manufacturer. An AV receiver with DLNA can, for example, play a movie directly from the hard drive of a computer in the next room, or transfer photos from a smartphone to the TV. Connecting to the Network can be done either wired (LAN) or wirelessly (Wi-Fi, see above).

- Roon Tested. Roon Tested accreditation means the AV receiver is compatible with the popular audiophile music streaming platform Roon. Certified models have undergone a series of tests and meet the quality standards required to operate Roon flawlessly. This ensures convenient management and organization of content within the platform.

— Coordination of Remote control. A function that allows you to connect the AV receiver to another device (for example, a Blu-ray player or external amplifier) and control both devices with one remote control. When purchasing equipment with such a function, it is necessary to clarify compatibility - as a rule, only equipment from one manufacturer can work in such a “bundle”, and even in such cases, their own nuances are possible upon agreement.

— Voice assistant. Receiver support for voice assistant. The most popular assistants these days are:

• Google Assistant
• Apple Siri
  
• Amazon Alexa

However, other solutions may also emerge. In any case, it is worth noting that we are not talking about an assistant built into the receiver itself, but about compatibility with external devices that have this function (for example, a smartphone or tablet). But even such compatibility allows you to give commands to the receiver by voice - this is often more convenient than more traditional control methods. The specific set of supported commands and languages may vary depending on the voice assistant and its specific version.

A decoder can be broadly described as a standard in which digital audio (often multi-channel) is recorded. For normal playback of such sound, it is necessary that the corresponding decoder is supported by the device. The first signs of multi-channel decoding were Dolby Digital and DTS, gradually improving and introducing new features. The final stage for 2020 is Dolby Atmos and DTS X decoders. And the intermediate ones were Dolby TrueHD, Dolby Pro Logic II, DTS-HD, DTS ES, DTS Neural: X, DTS Neo (6, X).

Dolby Atmos. A decoder that does not use a rigid distribution of sound across channels, but the processing of audio objects, due to which it can be used with almost any number of channels on a reproducing system — the sound will be divided between channels so that each audio object is heard as close as possible to its proper place. When using Dolby Atmos, in-ceiling speakers (or speakers facing the ceiling) are highly desirable. However, in extreme cases, you can do without them.

— DTS X . An analogue of the Dolby Atmos described above, when the sound is distributed not through individual channels, but through audio objects. The...digital signal contains information about where (according to the director's intention) the object audible to the user should be and how it should move, and the processor of the reproducing device processes this information and determines exactly how the sound should be distributed over the available channels in order to achieve the required localization. Thanks to this, DTS X is not tied to a specific number of audio channels — there can be as many as you like, the system will automatically divide the sound into them, achieving the desired sound. Also note that this decoder allows you to separately adjust the volume of dialogues.

— IMAX Enhanced. The IMAX Enhanced Mark of Conformity is awarded to equipment that meets the audio certification requirements of IMAX Corporation. Combined with DTS audio technology to deliver signature IMAX theater-like sound in the home. The most accurate reproduction of such audio is possible in systems with a large number of channels (5.1 or more). Note that for a fully immersive experience, IMAX Enhanced certification must also apply to video equipment for playing content (TV, projector, etc.).

The number of analogue stereo RCA inputs provided in the design of the AV receiver. The more such inputs there are, the more transmitting devices can be simultaneously connected to the receiver. Thanks to this, when choosing between them, you do not have to reconnect cables — just set the signal source in the receiver settings.

By itself, the RCA connector (colloquially — "tulip") can be used in different interfaces. However, in this particular case, we are talking about a linear audio input responsible for an analogue audio signal. RCA is the most popular connector used in modern audio equipment for such inputs; it allows you to connect the receiver to an external audio source such as a CD player.

Note that connectors of this type are usually counted in pairs; in other words, one input consists of two RCA connectors. This is due to the fact that in this case only one channel of analogue audio can be transmitted over one wire; accordingly, two RCA jacks are required for stereo transmission.

The number of coaxial inputs provided in the design of the receiver.

The coaxial interface is used to transmit audio in digital format. In fact, this is a kind of S / PDIF interface that uses an electric coaxial cable with RCA connectors (“tulip”) for connection. Do not confuse this interface with the analogue RCA described above: the coaxial connection differs in signal type, in the number of jacks per connector (one is enough here), and also does not work well with a regular RCA cable (preferably shielded). S/P-DIF bandwidth is enough to transmit multi-channel audio up to 7.1(see "Number of channels"), but lossless formats like Dolby TrueHD or DTS-HD Master Audio(see "Decoders") are not supported.

As for the quantity, the presence of several inputs allows you to connect several signal sources to the receiver at once with the corresponding outputs and switch between them through software settings without fiddling with switching cables.

The number of HDMI inputs provided in the design of the receiver.

This interface is one of the most advanced digital standards used in modern electronics. It was originally developed for HD television and already in the first version it allowed to transmit a video signal with Full HD (1920x1080) resolution, accompanied by eight-channel (7.1, see "Number of channels") sound; in the future, the maximum resolution increased even more. Almost all modern TVs, monitors and plasma panels have at least one HDMI interface, the same applies to playback devices (players, media centers, etc.).

As for the quantity, the presence of several inputs allows you to connect several signal sources to the receiver at once with the corresponding outputs and switch between them through software settings without fiddling with switching cables. In the case of HDMI, the abundance of connectors is especially important, given the prevalence of this standard in modern video equipment; in some receivers, the number of such inputs can be up to 10.

HDMI interface version supported by the receiver. Usually, all HDMI connectors available in the device correspond to this version — both inputs (see above) and outputs (see below). Here are the current options:

— v 1.4. The oldest of the current versions, released in 2009. However, it supports 3D video capable of working with resolutions up to 4096x2160 at 24 fps, and in Full HD resolution, the frame rate can reach 120 fps. In addition to the original v.1.4, there are also improved modifications — v.1.4a and v.1.4b; they are similar in terms of basic features, in both cases the improvements affected mainly work with 3D content.

-v 2.0. Significant update to HDMI introduced in 2013. In this version, the maximum frame rate in 4K has increased to 60 fps, and the audio bandwidth has increased to 32 channels and 4 separate streams simultaneously. Also from the innovations, we can mention support for the ultra-wide format 21:9. In the v.2.0a update, HDR support was added to the interface capabilities, in v.2.0b this feature was improved and expanded.

— v 2.1. Despite the similarity in name to v.2.0, this version, released in 2017, was a very large-scale update. In particular, it added support for 8K and even 10K at speeds up to 120 fps, as well as further expanded the possibilities for working with HDR. Under this version, its own cable was released — HDMI Ultra High Speed, all v.2.1 features are available only when using cables of this standard,...although basic functions can be used with simpler cords.