Printer Parts

Necessary accessories, compatible with Ender 3 V2, Ender 3 Pro, Ender 3 Series, Ender 5 Pro, Ender 5 Plus, CR10 Series and Other 3D printers. Suitable for 2020 V-series aluminum profiles, adjust the sliding smoothness by adjusting the hex eccentric column. Pulley Diameter: about 24mm/ 0.9 inch. Pulley Height: about 11mm/ 0.4 inch. Material: Back Plate is made of high quality cold rolled sheet material, pulley is made of high quality polyformaldehyde, very durable and smoothy. Exact replacement f

Circular arc Tooth Profile Tooth Space is Small, Suitable for Straight Line Driving. 2GT System is an Extension of The HTD System With Greater Load Carrying Capacity. Breaking Strength: 86 N per 1 mm (62 lbs. per 1/8") Belt Width. Working Tension: 111 N for 25.4 mm Belt (25 lbs. for 1"belt). Temperature Range: -34°C to +85°C (-30°F to +185°F)

Note These copper alloy nozzles only use for Creality Ender 5 S1/Ender 7 3D Printers and Spider 1.0 hotend kit, not suit for other hotend kit. Compatibility Those Spider Hotend Nozzle are supported filaments: PLAABSPETGTPUPPPCNylon and more. Quality Assurance These nozzles are made of high-quality copper alloy material. Heavy duty and provide a long service life. Easy to install and change. Package Included Parcel come with 2PCS 0.4mm Nozzle and 2PCS 0.6mm Nozzle. After Sales Service We pay grea

Dual Ball bearing fan, Long lifetime 50000Hours tested under 40degree temperature It has two sides, but the side with sticker must be always facing the hotend (not visible when the fan is mounted). Otherwise, the cooling won't work properly. 5V DC 0.1A, This fan is used for Prusa i3 MK3 MK3S MK2/2.5 3D printer Extruder Power connector: 3pin with RPM measuring function Package: 2pieces 4010 Left hotend fan

Fine sizes assorted - 0.15 mm, 0.25 mm, 0.35mm, 0.4 mm and 0.5 mm cleaning needles not only suitable for most of sizes nozzle but also they can use for cleaning other small parts, such as throat and feeder gear Premium material - SIQUK 3D printer nozzle cleaners are made of premium stainless steel material, sturdy, durable and flexible, easy to twist Wide compatibility - compatible with most of 3D printers extruder nozzles offered from E3D Makerbot, MK8 Makerbot Rep Rap Free gift - come with 2 d

1.Good Compatibility: This auto leveling sensor kit is designed for CR-6 SE/for CR-6 SE Max 3D printer. 2. Easy to Install: The same as most other auto-leveling sensors. 3. Applicable Model: for CR-6 SE. Auto Leveling Sensor Kit for CR-6 SE*1. 4. Practical Part: A practical part for your printer. Weight: about 63g. 5. Premium & Functional: Intelligence, self-check and alarm. The auto leveling function is adopted to make it easier to use and to increase the success rate of shaping.

Brass nozzle: Screw diameter: M6Screw Length: 13mm Size: 21mm*7mm Filament size: 1.75mm Tolerance: ± 0.1 mm Electroplated copper nozzle: corrosion resistant, high temperature resistant durable. suitable for hiah temperature 3D printing that other nozzle cannot handle Volcano nozzle: Higher Temperature Resistance, Higher Wear Resistance, Non-stick, Better Durability, Suitable for printing PLA, ABS, TPU, PA, PEEK, PEL, Carbon Fiber,Fiberglass and all other material Inner hole roughness: Ra0.4Nozzl

[Super Durable Tungsten] - MK8 extruder nozzles are made by paramount hardened tungsten steel, with longer lasting time than the normal brass nozzle. The hardness is beyond HRC60, can reduce the abrasion to the inner and outer of the nozzle during long time printing, more heat-resistant and more durable than ordinary brass nozzle. [Super High Temperature Resistance] - The max temp of this hardened tool steel nozzle could reach at 450c, suitable for 3D printing at high temperature, compatible wit

Premium Quality - Unlike the smaller diameter cleaning needle that can pass through both ends.The diameter of the cleaning needle is >1mm, it can only enter from the filament entry end and cannot pass through the filament extrusion end.24 PCs nozzle kit. With brass nozzles and hardened nozzles. Good abrasion resistance, heat resistance, and corrosion resistance.It is convenient for you to replace them in time to achieve high-quality printing. Package List - The 3D printer extruder nozzles come w

Made from International brass material, Feeding Chamfer with Round Aperture: The nozzle is designed in smooth feeding chamfer with round aperture, which greatly helps reduce friction resistance to the filament, promoting smoother filament feed-in. Uniquely designed MK nozzle is Crafted with advanced processing technique, helping deliver much smoother final prints. Sleek inner wall Smooth filament feed-out: Compared to Common nozzle, MK nozzle has smooth inner wall with less glitches, lower visco

SILICA GEL MATERIAL: Silicone column heat bed leveling adopts quality silicone material, stable and flexible, with nice heat resistant feature, can nicely reduce the vibrations when working, providing good leveling performance for your 3D printer. REDUCED VIBRATION: Silicone leveling column ender 3 replaces the compression spring that connects the heated bed to the X-axis bracket, permanently leveling the end. They will be effectively and stably installed on your 3D printer and will not easily m

Function: Unique needle structure design can effectively clean the nozzle of the 3D printer, removing the blockage, suitable for mild maintenance of nozzle, 5 MK8 Nozzles can regularly replace Features: The 3D printer cleaning needle has high toughness and is not easy to break, simple cleaning the difficult-to-clean places like the feed gears; The nozzle is made of high-quality brass and has a long life 5 MK8 Nozzles 0.4 mm: 3D printer extruder Mk8 nozzles, high-temperature resistance, wearable,

Thermistor Color: white,Cartridge Heater Material: 304 Stainless Steel Voltage: 24v, Power: 40w,Diameter: 6mm ; Length: 20mm Temperature sensor 100K accuracy of ± 1% Conviniently pre-wired with 1 meter long high temperature teflon insulated wiring Support for NTC 3950 is included in Marlin firmware, use TEMP SENSOR 11 in firmware configuration

Iverntech 3d printer filament holder Widely used for most pla, abs, wood, tpu, nylon, flexible filaments Much firmly design, won't fall down with all kinds of filaments The sticker paper can be peeled off before assemble it Filament pictured is for display purpose only, not included

High torque Low noise Nema 17 stepper motor with step angle 1.8deg Holding Torque: 45Ncm(63.74oz.in), Voltage: 12-24VDC Rated Current/phase: 1.50A & Phase Resistance: 2.3ohms Build with 1 Meter Pin Connector

Ender 3 Neo/Ender 3 V2 Neo/Ender 3 Max Neo Original Accessories. Durable to use: the silicone case has good flexibility and can be placed close to the heating block, it is easy to install, stable and not easy to fall off, very strong. Suit for Creality Ender 3 Neo, Ender-3 V2 Neo, Ender-3 Max Neo, CR-6 SE, CR-6 Max, CR-10 Smart, CR-5 PRO 3D Printer Hotend, Please know before ordering, this is NOT sutiable for the hotend of Ender 3, Ender 3 V2Ender 3 Pro and CR10 CR10S series. Helps to keep the h

Original Authentic - 100% Original Capricorn XS Series Bowden tubing. High Lubricity Additives make our XS Series tubing the lowest friction Bowden tubing on the market. Precise Print - Less friction means more responsiveness, less retraction, more accurate prints, less slippage, wear, and tear on the extruder, and less clogging when printing chunky filaments such as wood fill or iron fill. Excellent Performance - Capricorn Bowden tubing is designed specifically for 1.75mm filament, the filament

Compatibility: Compatible with almost all series of Creality Ender and metal hot end kits for CR printers. Such as Ender 3, Ender 3 Pro, Ender 3SCR-10, CR10, CR10S, etc.The hotend is pre-assembled for easy installation. Pluggable: the heating tube and temperature thermistor that from control box, connect them with terminal housing and pin. Then you could plug the hotend kit, easier to replace hotend kit. MK8 extruder hot end kit, white wire was temperature thermistor, braided wire was heating tu

Package contents: you will receive 28 pieces of stainless steel nozzle cleaner in 5 sizes, 2 pieces of storage boxes, 8 pieces of cleaning copper wire toothbrushes in 2 styles, 2 pieces of tweezers in 2 different styles, sufficient quantity and tools can meet your daily use Various sizes: these stainless steel nozzle cleaner have 5 different sizes, including 12 x 0.4 mm, 10 x 0.35 mm, 2 x 0.5 mm, 2 x 0.15 mm, 0.25 x 2 mm, which can meet your different using needs, suitable for nozzle in most siz

The funnel is made of stainless steel, easy to use and clean, and effectively filters the contaminants while the resin is poured into the bottle The strainer are perfectly clean, tight and the mesh is the right size for filtering resin. Thanks to the funnel, the residues can be filtered back clean and suitable for filtering resin. Stainless steel filter (sits very well in the stainless steel funnel). More practical than the paper filter, simply wipe them out after use and clean them with isoprop

Compatible for Ender-3/Pro, Ender 3 V2, Ender 5/pro,CR-10. The bracket made of high quality metal material, high strength, durable and wear-resistant. 5 pin cable is about 1.3m, the split cable is about 1.5m. Easy to install,easy to install, with wrench included in the package. After-sales services: if you have any question during usage, please free free to contact us!

Compatible Models: This silicone socks and nozzles kit is compatible with Anycubic Vyper, Kobra Plus, Kobra Max FDM 3D Printers. Silicone Socks: The silicone sock is made of high quality silicone, which can withstand high temperature of 300 and can avoid burns when your hand accidentally touches the print head during printing, and also keep the heating block and nozzle clean. 0.4mm Brass Nozzles: The nozzle is made of high quality brass with smooth inner wall and no burr, which can ensure even a

Suitable for Ender 3,Ender 3 pro ,Creality CR-10S series 3D Printer and other NEMA 17 stepper motors (for 5mm to 8mm shaft diameter) it also can be used with other 3D printers and CNC machines which are using 5mm shaft motor to 8mm lead screw. Size: OD20mm x 25mm L; Material: aluminum Package: 4pcs

Sponsored by eBay