USA
Catalog   /   Camping & Fishing   /   Fishing   /   Boat Motors

Comparison Mercury F6M vs Sea-Pro F6S

Add to comparison
Mercury F6M
Sea-Pro F6S
Mercury F6MSea-Pro F6S
from $1,466.16 up to $1,488.52
Outdated Product
Outdated Product
TOP sellers
Applicationboatboat
Motor typepropellerpropeller
Motor
Engine typepetrolpetrol
Motor duty cycle4-stroke4-stroke
Maximum power6 hp6 hp
Maximum power4.4 kW4.4 kW
Maximum revolutions6000 rpm5500 rpm
Number of cylinders1 pcs1 pcs
Capacity123 cm3139 cm3
Piston diameter59 mm62 mm
Piston stroke45 mm46 mm
Coolingliquidliquid
Exhaust systemthrough the propellerabove propeller
Generator system
Power source12 V
Maximum current strength4 А
Fuel system
Fuel system typecarburetorcarburetor
Fuel tankexternalbuilt-in
Fuel tank volume12 L1.1 L
Recommended fuelAI-92 gasolineAI-92 gasoline
Drive unit
Gear ratio2.152.08
Propeller screw3-bladed3-bladed
Gear
forward
neutral
reverse
forward
neutral
reverse
Equipment
Transom height (deadwood)381 mm381 mm
Control systemtillertiller
Launch typemanualmanual
Leg lift (trim)manualmanual
General
Dimensions557x329x1039 mm
Weight25 kg25 kg
Added to E-Catalogjune 2015february 2015

Maximum revolutions

The highest shaft speed that the outboard motor is capable of developing.

Theoretically, the speed of rotation of the propeller (or turbine — see "Motor type") depends on the engine speed, and, accordingly, the speed that the boat is capable of developing. However, in addition to this indicator, many other factors also affect the performance of the motor — engine power (see above), gear ratio (see below), propeller design, etc. As a result, situations are quite normal when a more powerful and high-speed motor has lower revolutions than the weaker one. Therefore, this parameter is, in fact, a reference one, and has almost no practical value when choosing. Unless it can be noted that high-speed motors are more susceptible to noise and vibration than low-speed ones; however, this moment can be compensated by the use of various technical tricks.

Capacity

The working volume of a gasoline outboard engine (see "Engine type"). This term usually means the total working volume of the cylinders.

The larger this value, the higher the motor power, usually (see the relevant paragraph). At the same time, with an increase in the working volume, fuel consumption, weight and dimensions of the unit also increase; and power depends not only on this indicator, but also on a number of other factors — ranging from the number of strokes (see "Engine duty cycle") or the presence of turbocharging (see below) and ending with specific design features. Therefore, situations are not excluded when a smaller engine will have more power, and vice versa.

Piston diameter

The diameter of a single piston in a gasoline (see "Engine type") outboard motor. In most cases, this parameter is purely reference; situations where data on the piston diameter is really needed are extremely rare — usually during the repair or maintenance of the engine.

Piston stroke

The working stroke is the distance between the two extreme positions of the piston in a gasoline (see "Engine type") outboard motor. In most cases, this parameter is purely reference; situations where such data is really needed are extremely rare — usually during the repair or maintenance of the engine.

Exhaust system

The design of the exhaust system in a gasoline outboard motor (see “Engine type”), more precisely, the method of exhaust gases used in this system.

Above the screw. This category includes two types of engines. The simplest option is when exhaust gases are emitted directly into the air. Such systems are extremely simple and cheap, but the exhaust can create a noticeable inconvenience for people in the boat (not only because of the gases, but also because of the rather high noise level); therefore, they are found only in the simplest outboard motors, and even then quite rarely. A more common option is to release exhaust gases into the water above the propeller (most often through the so-called anti-cavitation plate — a flat ledge above the propeller). Such systems are more comfortable than "air" ones, while they are simpler and cheaper than propeller exhaust (see below), although they are still considered less technically advanced.

Through the screw. In systems of this type, the exhaust is led into the water directly through the propeller hub; in fact, the position of the exhaust pipe coincides with the axis of rotation. This reduces the noise level compared to systems using exhaust over the propeller, and also slightly increases power and traction characteristics. The downside of these advantages is the design complexity and, accordingly, the high cost.

Generator system

Possibility to use a petrol engine generator(see "Engine type") to power an external load.

The generator is an indispensable element in the design of any petrol engine — it is responsible for creating the spark necessary for ignition. However, not every outboard motor has the ability to power an external load from this generator — therefore, if such an opportunity is important to you, you should choose a model where it is directly stated. And the generator system can come in handy, first of all, if you plan to use additional equipment on the boat — power from the generator is in a number of ways more convenient than from autonomous batteries, and it is for it that many navigation systems, echolocation, radio communications and other instruments and equipment are made . In addition, if necessary, devices outside the boat can also be powered from the generator — for example, a starting charger for a car.

Power source

The supply voltage supplied by the generator system installed in the outboard motor.

Almost all such systems work with a voltage of 12 V — this is a standard widely used in modern automotive and water technology, it is under it that the electrical systems of the engines themselves, and electronic devices for cars and boats are made. There are practically no exceptions to this rule.

Maximum current strength

The highest current that the generator system installed in the outboard engine is capable of delivering (see above). The characteristics of the load that can be connected to the generator depend on this indicator: its total current consumption should not be higher than the maximum current of the generator, otherwise the latter will work with overload, which is fraught with malfunctions and even accidents. Also, this information is useful if you plan to use the generator to charge batteries (car or boat): each battery has its own charging current, and the power source must match them.

Fuel tank

The type of fuel tank used by the gasoline outboard motor (see "Engine type").

Built -in. As the name implies, in such engines the fuel tank is an integral structural element. This eliminates the need for the user to look for a separate fuel tank and build a system for supplying gasoline from the tank to the engine. On the other hand, the tank significantly increases the dimensions and weight of the entire structure, which is especially important for two-wheel tractor control (see below). Therefore, for powerful engines that consume a lot of fuel and require volumetric tanks for its storage, this option is poorly suited — it is typical for relatively modest models whose power does not exceed 25 hp.

External. This category includes engines that do not have built-in fuel tanks and are designed to supply fuel from a separately located container through a special hose. The tank itself is most often supplied as a kit, but there are exceptions. However, anyway, the absence of a fuel tank directly in the motor housing makes the motor itself lighter, more compact and more mobile (the latter is relevant for models with a two-wheel tractor control system, see below). And for powerful high consumption units that require appropriate tanks, this is generally the only available option — otherwise the motor would turn out to be too heavy and bulky.
Mercury F6M often compared
Sea-Pro F6S often compared