Comparison Yamaha A-S701 vs Yamaha A-S500

The total capacitance of the capacitors installed in the power supply of the amplifier. Usually, for ordinary lovers of high-quality sound, this indicator is not practically significant: the capacitance is selected in such a way as to optimally (or at least minimally) match the characteristics of the amplifier. However, for demanding audiophiles who pay attention to the smallest details of audio system components, capacitors are also often of interest.

The fact is that they are an important part of the rectifier circuit — they smooth out current fluctuations that arise both due to the imperfection of the rectifiers themselves and due to various external factors. Knowing the total capacitance of the capacitors, one can also evaluate the efficiency of their work: the higher this indicator, the more stable the power supply will work and the lower the likelihood of sound distortion due to its fault. There are special formulas that allow you to derive the optimal capacitance of capacitors depending on the type, power and other parameters of the amplifier; they can be found in specialized sources.

The range of audio frequencies that the amplifier is capable of handling. The wider this range, the more complete the overall picture of the sound, the less likely it is that too high or low frequencies will be “cut off” by the output amplifier. However, note that the range of sound audible to a person is on average from 16 Hz to 20 kHz; There are some deviations from this norm, but they are small. At the same time, modern Hi-Fi and Hi-End technology can have a much wider range — most often it is a kind of "side effect" of high-end circuits. Some manufacturers may use this property for promotional purposes, but it does not carry practical value in itself.

Note that even within the audible range it does not always make sense to chase the maximum coverage. It is worth, for example, to take into account that the actually audible sound cannot be better than the speakers are capable of giving out; therefore, for a speaker system with a lower threshold of, say, 70 Hz, there is no need to look for an amplifier with this figure of 16 Hz. Also, do not forget that a wide frequency range in itself does not absolutely guarantee high sound quality — it is associated with a huge number of other factors.

The nominal sound power output by the amplifier per channel when operating with a load having a dynamic resistance (impedance) of 8 ohms. In our catalog, this parameter is indicated for the mode when all channels of the amplifier work under load (see "Number of channels"); in the presence of unused channels, the rated power may be slightly higher, but this mode cannot be called standard.

Rated power can be simply described as the highest output signal power at which the amplifier is able to work stably for a long time (at least an hour) without negative consequences. These are average figures, because in fact, the audio signal is by definition unstable, and individual level jumps can significantly exceed the rated power. However, it is she who is the main basis for assessing the overall loudness of the sound.

This indicator also determines which speakers can be connected to the amplifier: their rated power should not be lower than that of the amplifier.

According to the laws of electrodynamics, with different dynamic load resistance, the output power of the amplifier will also be different. In modern speakers, the standard values \u200b\u200bare 8, 6, 4 and 2 Ohms, and power levels are indicated for them.

The nominal sound power output by the amplifier per channel when a load with a dynamic resistance (impedance) of 6 ohms is connected to it. See Power per Channel (8Ω) for more information on power rating and its relationship to impedance.

In itself, the signal-to-noise ratio is the ratio of the level of pure sound produced by the amplifier to the level of extraneous noise that occurs during its operation. This parameter is the main indicator of the overall sound quality — and very clear, because. its measurement takes into account almost all the noise that affects the sound in normal operating conditions. A level of 70 – 80 dB in modern amplifiers can be considered acceptable, 80 – 90 dB is not bad, and for advanced audiophile-class devices, a signal-to-noise ratio of at least 100 dB is considered mandatory.

If the specifications do not specify for which output the signal-to-noise ratio is indicated, it usually means its value for the linear input (see "RCA (par)"). This is quite enough to evaluate the quality of the device for this parameter. However, some manufacturers indicate it for other inputs — Main, Phono; see below for more on this.

Signal-to-noise ratio when the amplifier is operating through the Main input. For more details on the value of the signal-to-noise ratio, see the relevant paragraph above, about the Main input — p. "Input to the amplifier (Main)".

signal-to-noise ratio when the amplifier is driven through the Phono input. This interface is for connecting turntables; its features are described in the “Inputs” section below, and for the meaning of any signal-to-noise ratio, see the corresponding section above.

This indicator describes the amount of non-linear distortion introduced by the amplifier into the processed signal. Such distortions are not necessarily perceived as extraneous noise, but they degrade the quality of the sound anyway — for example, they can make it more deaf. It is almost impossible to avoid them, but it can be reduced to levels inaudible to the human ear.

As a result, the harmonic distortion factor (harmonics) is one of the main parameters describing the overall sound quality in Hi-Fi and Hi-End amplifiers. The lower it is, the clearer the sound. Hundredths of a percent are considered a good indicator for modern amplifiers, thousandths and below are excellent. The exceptions are tube and hybrid models, for which rather high harmonic coefficients are allowed; see "Element base" for more details.

— Euroblock. Analogue audio input (usually line level) using a Euroblock connector. This connector, used mainly in professional audio equipment, is remarkable in that it is attached to the wire using terminals. This is extremely convenient when working with stripped wires (which is often required in professional applications): screwing such a wire to the plug once and connecting / disconnecting the plug to the Euroblock connector is much easier than constantly unscrewing / screwing the terminals. In addition, such a connection is often made balanced (see "XLR (balanced)" below). Inputs of this type are found mainly in information and information-concert amplifiers (see above).

— Phono. Dedicated input for connecting to the amplifier turntables; often has a suffix indicating the type of cartridge that is compatible, such as "Phono MM" or "Phono MM/MC" (see "Advanced — Phono Stage" for details). Despite the proliferation of digital formats, these players are still highly regarded by audiophiles for their high quality and fidelity, and are often used in premium audio systems. However, connecting a "turntable" has its own characteristics — in particular, it requires a phono stage (for more details, see ibid.) — and standard inputs are unsuitable for this purpose. Therefore, a Phono jack is a must if you want to connect your turntable directly, without an external phono stage.

— USB B. The USB interface is widely used in com...puter technology for various peripherals. The presence of a type B input means that the amplifier can be connected to a computer as an external controlled device (slave). Most often, with this connection, it is used as an external sound card or audio interface — this provides higher sound quality and more extensive options for its settings than most built-in sound cards, even expensive ones. However, the matter is not limited to this: in some models, via USB type B, you can update the firmware or change the special parameters of the amplifier.

— Coaxial S / P-DIF. Digital audio input, a variation of the S/P-DIF interface based on a conventional electrical signal (the second variation, optical, is described below). Usually uses a common RCA connector, known as a "tulip", but has rather strict cable requirements. The bandwidth of any version of S / P-DIF is quite sufficient even for high-quality multi-channel sound, and the coaxial version itself is simpler, cheaper and more reliable than the optical one, but more susceptible to interference.

— Optical. Input for transmitting digital sound using light signals, via TOSLINK fiber optic cable; one of the versions of the S/P-DIF standard. The main advantage of optical fiber over traditional electrical cables is complete insensitivity to electrical interference; at the same time, it is more expensive and requires rather careful handling (in particular, it does not tolerate sharp bends).

— Balanced digital ( AES/EBU). The AES/EBU interface is used in the professional field to transmit audio in digital format. It can use several connection types; in this case, it means transmission over the so-called balanced line using an XLR connector. Both the principle of balanced connection and the connector itself are described in detail in the “XLR (balanced)” section below — however, in the case of AES / EBU, we are talking about a digital signal, not an analogue signal.

— COM port ( RS-232). A connector used to control the amplifier from a computer. Through it, you can change the settings, incl. and quite thin, and in some models even update the firmware. Usually, for such purposes, special software is required, which can be supplied with the amplifier.

— Control input (IR). Connector for connecting an external infrared remote control receiver. When properly placed, such a receiver will allow you to use the remote control even in places where the signal from the remote control cannot reach the main (built-in) sensor — for example, in another room. For such purposes, not only sensors can be used as a separate device, but also system components that are compatible with the remote control — for example, players or tuners.