Comparison Makita HR2470X15 vs Makita MT M8701

Rated power consumed by the rotary hammer during operation. Usually, the maximum power consumption in normal operation is taken as the nominal power.

In general, the higher this indicator, the heavier and more performant the rotary hammer is, the more advanced its performance usually turns out to be. On the other hand, the electricity consumption of such tools is high. In addition, note that with the same power consumption, the actual set of individual characteristics for different tools may be different. For example, frequency and impact energy are inversely related, and for the same power input, higher frequency usually means less individual impact energy. So, according to this parameter, it is worth evaluating only the overall level of the instrument; for accurate selection for specific tasks, you need to pay attention to more specific characteristics.

Also note that power consumption data can be useful for some tasks related to catering — for example, if a construction site is powered by an autonomous generator and you need to estimate the load on this energy source.

The energy transmitted by the perforator to the material being processed upon impact; the higher this indicator, the stronger and more powerful each individual blow.

First of all, we recall that the energy of impacts is directly related to their frequency: an increase in frequency leads to a decrease in energy. Therefore, for models where the number of strokes can be adjusted, this paragraph usually gives the maximum energy achieved at the minimum speed of operation.

In general, higher impact energy improves efficiency when working with hard, stubborn materials, but requires more motor power (especially if it has to be combined with a high frequency). Therefore, it is worth choosing according to this parameter, taking into account specific tasks. So, for occasional use in everyday life, an energy of 2 J or less is enough, for home repair work of medium intensity, at least 3 J is desirable; a power of 4 J or more is already considered high; and in some industrial-grade perforators, this figure can reach 30 J.

The speed of rotation of the working equipment provided by the rotary hammer. Usually, this indicates the speed at idle, without load; rated load speeds can be further specified in the characteristics (see below), but this is rare, and this parameter is still considered the main characteristic. It is also worth mentioning that in the presence of a speed controller (see "Functions"), the maximum speed value is given here.

When working in the main mode — drilling with impact — the rotation of the equipment is used mainly to remove waste from the hole, and the revolutions here are of no fundamental importance (they can be very low). Therefore, it is worth paying attention to this indicator mainly in cases where the rotary hammer is planned to be often used for conventional drilling, without impact. And here it is worth proceeding from the fact that high speeds increase productivity and contribute to accuracy when working with some materials, but reduce torque (compared to tools with the same engine power). So for heavy work with hard, stubborn materials, relatively "slow" tools are usually better suited.

Note also that drilling is not the main task of rotary hammers; therefore, their rotation speeds are noticeably lower than those of the same drills. On the other hand, in this case, low speeds are often compensated by powerful engines and high torque, which makes it possible to effectively drill holes...of a fairly large diameter, including using crowns.

The maximum tool diameter that can be used with a rotary hammer when drilling in concrete. See "Maximum drilling diameter in wood" for details.

The maximum tool diameter that can be used with a rotary hammer when drilling with a hollow core. Crowns are used to create holes of large diameter (from 40 mm) in hard materials such as reinforced concrete and stone. See "Maximum drilling diameter in wood" for details on the maximum diameter.

- Additional handle. The puncher has an additional front handle, usually located at the base of the cartridge. This handle can be non-removable or removable, rigidly fixed or movable. Holding with two hands for two handles is much more convenient than for one and the body, because. allows you to optimally distribute the load on the hands; this is especially important for long-term work and the processing of "heavy" materials.

- Depth stop. A device that allows you to make recesses of a strictly defined depth at once, without constant measurements and without the risk of drilling deeper than necessary. It usually looks like a rod attached to the body of the puncher parallel to the working tool. In use, this rod extends to such a length that when the desired depth is reached, it rests on the surface of the material being processed, preventing the drill from moving further.

- Chisel. Complete nozzle for impact work with a perforator in the manner of chasing, leveling hard surfaces, beating tiles, bricks, concrete, etc. For different tasks, various types of chisels are produced - flat, spade, groove, crushing peaks with a sharp tip.

— Bur. The presence of a drill in the delivery set of a tool designed for processing various hard materials due to drilling with impact. The purchase of such a set eliminates the need...to look for a drill separately, however, the characteristics of the complete nozzle must be clarified before purchase, because. they may not meet the requirements of the buyer.

- Charger. The presence of a charging unit in the configuration allows you to charge the batteries. Accordingly, for models with batteries, this accessory is necessary to power the battery. However, there are models without a charger. And punchers with it may differ in the model of the charger, the name of which will allow you to learn more about its characteristics and, if necessary or as needed (breakdown), buy a similar one.

- Case included. The presence of a special case in the delivery set, which facilitates storage and transportation: it provides protection against shocks and adverse conditions (moisture, frost), is equipped with a special carrying handle, in addition, along with the punch itself, a set of working tools can be placed in the case, replaceable cartridges, etc.

- Dust collector. The presence of a special dust collector in the delivery set of the perforator. As the name implies, it is designed to collect the dust generated during operation, which can otherwise create a significant inconvenience. Usually looks like a bag or container attached to the body; can be either replaceable (thrown away with the collected garbage) or permanent. The dust collector slightly increases the weight and dimensions of the puncher, however, if necessary, it can be removed.

Power cord length for mains powered drills (see above). The longer the cord, the farther from the outlet you can use the unit and the less it depends on the location of the outlets.

The weight of a fully assembled rotary hammer (in the case of battery power, with a standard battery installed). Unlike many other types of equipment, in the case of rotary hammers, light weight is far from always an advantage. So, heavy models are better suited for professional use — they are less prone to vibrations and, usually, are stronger, which is important when working with difficult-to-cut materials for a long time. But for small, simple works of short duration, a lot of weight is not required, and in this case, light models are useful, which do not require significant effort to hold on weight.