Comparison Makita MT M8701 vs Makita BHR162RFE

— Drilling with impact. A mode of operation that combines rotation and percussive movement of the drill. Due to this, a complex effect on the treated surface is provided; in this case, the impact gives a direct advancement of the drill, and rotation is used primarily to remove the resulting waste. It is this format of work that allows you to effectively make holes in materials like concrete, brick, natural stone, etc .; at the same time, rotary hammers cope with such tasks much more efficiently than the so-called impact drills (drills supplemented with a chiseling function).

— Drilling (without impact). Traditional drilling, when the hammer works like a drill: the working equipment only rotates, not moving back and forth. It is applied to work with rather soft materials, such as a tree and metal. At the same time, rotary hammers are often more efficient than traditional drills — due to the greater power and weight of the tool, they allow you to drill larger and deeper holes with sufficient accuracy.

— Chiseling (demolition hammer). In this mode, the punch tool only moves back and forth, without rotation. This format of work can be useful when splitting large pieces of hard material, removing various coatings, etc. We emphasize that a rotary hammer, even a powerful and heavy one, will not replace a full-fledged demolition hammer; however, for relatively simple tasks — such as dismantling smal...l structures made of relatively soft materials, splitting tiles, chasing walls, etc. — a tool with this mode is quite suitable.

Rated power consumed by the rotary hammer during operation. Usually, the maximum power consumption in normal operation is taken as the nominal power.

In general, the higher this indicator, the heavier and more performant the rotary hammer is, the more advanced its performance usually turns out to be. On the other hand, the electricity consumption of such tools is high. In addition, note that with the same power consumption, the actual set of individual characteristics for different tools may be different. For example, frequency and impact energy are inversely related, and for the same power input, higher frequency usually means less individual impact energy. So, according to this parameter, it is worth evaluating only the overall level of the instrument; for accurate selection for specific tasks, you need to pay attention to more specific characteristics.

Also note that power consumption data can be useful for some tasks related to catering — for example, if a construction site is powered by an autonomous generator and you need to estimate the load on this energy source.

The energy transmitted by the perforator to the material being processed upon impact; the higher this indicator, the stronger and more powerful each individual blow.

First of all, we recall that the energy of impacts is directly related to their frequency: an increase in frequency leads to a decrease in energy. Therefore, for models where the number of strokes can be adjusted, this paragraph usually gives the maximum energy achieved at the minimum speed of operation.

In general, higher impact energy improves efficiency when working with hard, stubborn materials, but requires more motor power (especially if it has to be combined with a high frequency). Therefore, it is worth choosing according to this parameter, taking into account specific tasks. So, for occasional use in everyday life, an energy of 2 J or less is enough, for home repair work of medium intensity, at least 3 J is desirable; a power of 4 J or more is already considered high; and in some industrial-grade perforators, this figure can reach 30 J.

The number of beats per minute provided by the punch. For models in which the beat frequency can be adjusted, this item indicates the entire adjustment range, for example "1600 — 3000".

High impact frequency, on the one hand, increases the productivity of the tool and can significantly reduce the time required for work. On the other hand, with the same engine power, an increase in the number of strokes per minute leads to a decrease in the energy of each stroke. Therefore, among heavy performant devices, a low frequency is often found — up to 2500 beats / min and even lower. And the ability to adjust the frequency of impacts allows you to adjust the hammer to the specific situation, depending on what is more important — productivity or the ability to cope with hard, stubborn material. For example, for old crumbling brickwork, you can set the speed higher, and for working with stone or dense concrete, it is better to reduce the frequency of impacts by directing engine power to increase the energy of each impact.

Summing up, we can say this: when choosing a perforator, you should focus on both the number of strokes and the impact energy. Detailed recommendations on this subject for specific situations can be found in special sources.

The speed of rotation of the working equipment provided by the rotary hammer. Usually, this indicates the speed at idle, without load; rated load speeds can be further specified in the characteristics (see below), but this is rare, and this parameter is still considered the main characteristic. It is also worth mentioning that in the presence of a speed controller (see "Functions"), the maximum speed value is given here.

When working in the main mode — drilling with impact — the rotation of the equipment is used mainly to remove waste from the hole, and the revolutions here are of no fundamental importance (they can be very low). Therefore, it is worth paying attention to this indicator mainly in cases where the rotary hammer is planned to be often used for conventional drilling, without impact. And here it is worth proceeding from the fact that high speeds increase productivity and contribute to accuracy when working with some materials, but reduce torque (compared to tools with the same engine power). So for heavy work with hard, stubborn materials, relatively "slow" tools are usually better suited.

Note also that drilling is not the main task of rotary hammers; therefore, their rotation speeds are noticeably lower than those of the same drills. On the other hand, in this case, low speeds are often compensated by powerful engines and high torque, which makes it possible to effectively drill holes...of a fairly large diameter, including using crowns.

The reverse allows you to switch the direction of rotation of the nozzle. It also indicates the type of switch responsible for the reverse. The options might be:

— Crawler. A switch in the form of a slider with two working positions (plus a neutral one between them, at which the tool does not turn on at all). Usually, it is able to move in the direction "back and forth" — this option is considered the most practical. The sliders are quite simple and at the same time convenient and visual.

— Flag. A switch in the form of a flag, usually installed above the start button and thrown to the right and left. One of the advantages of the checkbox is that it is right at your fingertips and can be switched almost “without unnecessary movements” (which is not always available for the slider).

— Brush (on the engine). The brush reverse differs from the two options described above not so much in the design of the switch as in the principle of operation: it changes the direction of rotation not by controlling the current on the motor windings, but by a special movable brush holder for this motor. This allows you to develop maximum power in any direction of rotation (which is not always available with electronic adjustment), and also reduces wear on individual engine components. The disadvantages of this option are complexity an...d high cost.

— Gearbox. A rather specific option: switching the direction due to the settings of the gearbox (the mechanism that transmits rotation from the engine to the cartridge). Here you can draw an analogy with turning on the reverse gear in a car: turning on the reverse affects only the cartridge with the tooling, the tool motor continues to rotate in the same direction. This allows you to use the full power of the motor in any direction of rotation; and the absence of unnecessary switches has a positive effect on the reliability of the electrical components of the tool. On the other hand, gears with a reverse function are quite complex and expensive, and therefore they are rarely found in individual professional-grade rotary hammers.

The maximum diameter of a tool that can be used with a rotary hammer when drilling in wood (and, accordingly, the maximum diameter of the resulting hole). With a large drilling diameter, the loads on the device increase, and some models may simply not be designed for them (despite the technical possibility of installing tools of the appropriate diameter), as a result, it is not worth exceeding the maximum specified diameter, because. this may damage the instrument.

The maximum tool diameter that can be used with a rotary hammer when drilling in concrete. See "Maximum drilling diameter in wood" for details.

The maximum tool diameter that can be used with a rotary hammer when drilling with a hollow core. Crowns are used to create holes of large diameter (from 40 mm) in hard materials such as reinforced concrete and stone. See "Maximum drilling diameter in wood" for details on the maximum diameter.