Comparison Denon PMA-600NE vs Denon PMA-520AE

The range of audio frequencies that the amplifier is capable of handling. The wider this range, the more complete the overall picture of the sound, the less likely it is that too high or low frequencies will be “cut off” by the output amplifier. However, note that the range of sound audible to a person is on average from 16 Hz to 20 kHz; There are some deviations from this norm, but they are small. At the same time, modern Hi-Fi and Hi-End technology can have a much wider range — most often it is a kind of "side effect" of high-end circuits. Some manufacturers may use this property for promotional purposes, but it does not carry practical value in itself.

Note that even within the audible range it does not always make sense to chase the maximum coverage. It is worth, for example, to take into account that the actually audible sound cannot be better than the speakers are capable of giving out; therefore, for a speaker system with a lower threshold of, say, 70 Hz, there is no need to look for an amplifier with this figure of 16 Hz. Also, do not forget that a wide frequency range in itself does not absolutely guarantee high sound quality — it is associated with a huge number of other factors.

This indicator describes the amount of non-linear distortion introduced by the amplifier into the processed signal. Such distortions are not necessarily perceived as extraneous noise, but they degrade the quality of the sound anyway — for example, they can make it more deaf. It is almost impossible to avoid them, but it can be reduced to levels inaudible to the human ear.

As a result, the harmonic distortion factor (harmonics) is one of the main parameters describing the overall sound quality in Hi-Fi and Hi-End amplifiers. The lower it is, the clearer the sound. Hundredths of a percent are considered a good indicator for modern amplifiers, thousandths and below are excellent. The exceptions are tube and hybrid models, for which rather high harmonic coefficients are allowed; see "Element base" for more details.

— Euroblock. Analogue audio input (usually line level) using a Euroblock connector. This connector, used mainly in professional audio equipment, is remarkable in that it is attached to the wire using terminals. This is extremely convenient when working with stripped wires (which is often required in professional applications): screwing such a wire to the plug once and connecting / disconnecting the plug to the Euroblock connector is much easier than constantly unscrewing / screwing the terminals. In addition, such a connection is often made balanced (see "XLR (balanced)" below). Inputs of this type are found mainly in information and information-concert amplifiers (see above).

— Phono. Dedicated input for connecting to the amplifier turntables; often has a suffix indicating the type of cartridge that is compatible, such as "Phono MM" or "Phono MM/MC" (see "Advanced — Phono Stage" for details). Despite the proliferation of digital formats, these players are still highly regarded by audiophiles for their high quality and fidelity, and are often used in premium audio systems. However, connecting a "turntable" has its own characteristics — in particular, it requires a phono stage (for more details, see ibid.) — and standard inputs are unsuitable for this purpose. Therefore, a Phono jack is a must if you want to connect your turntable directly, without an external phono stage.

— USB B. The USB interface is widely used in com...puter technology for various peripherals. The presence of a type B input means that the amplifier can be connected to a computer as an external controlled device (slave). Most often, with this connection, it is used as an external sound card or audio interface — this provides higher sound quality and more extensive options for its settings than most built-in sound cards, even expensive ones. However, the matter is not limited to this: in some models, via USB type B, you can update the firmware or change the special parameters of the amplifier.

— Coaxial S / P-DIF. Digital audio input, a variation of the S/P-DIF interface based on a conventional electrical signal (the second variation, optical, is described below). Usually uses a common RCA connector, known as a "tulip", but has rather strict cable requirements. The bandwidth of any version of S / P-DIF is quite sufficient even for high-quality multi-channel sound, and the coaxial version itself is simpler, cheaper and more reliable than the optical one, but more susceptible to interference.

— Optical. Input for transmitting digital sound using light signals, via TOSLINK fiber optic cable; one of the versions of the S/P-DIF standard. The main advantage of optical fiber over traditional electrical cables is complete insensitivity to electrical interference; at the same time, it is more expensive and requires rather careful handling (in particular, it does not tolerate sharp bends).

— Balanced digital ( AES/EBU). The AES/EBU interface is used in the professional field to transmit audio in digital format. It can use several connection types; in this case, it means transmission over the so-called balanced line using an XLR connector. Both the principle of balanced connection and the connector itself are described in detail in the “XLR (balanced)” section below — however, in the case of AES / EBU, we are talking about a digital signal, not an analogue signal.

— COM port ( RS-232). A connector used to control the amplifier from a computer. Through it, you can change the settings, incl. and quite thin, and in some models even update the firmware. Usually, for such purposes, special software is required, which can be supplied with the amplifier.

— Control input (IR). Connector for connecting an external infrared remote control receiver. When properly placed, such a receiver will allow you to use the remote control even in places where the signal from the remote control cannot reach the main (built-in) sensor — for example, in another room. For such purposes, not only sensors can be used as a separate device, but also system components that are compatible with the remote control — for example, players or tuners.

— Preamplifier (Pre-Amp). The presence in the design of the device of a separate output for the signal from the preamplifier. In the type of amplifiers of the same name (see "Type"), such an output is available by definition and is the main, and sometimes the only one. On integrated models (see ibid.) , the Pre-Amp output allows you to connect an external power amplifier and use it instead of the internal one. This feature can be useful, for example, to connect a more powerful speaker instead of the original one, or to work in Bi-amping mode. It is worth noting that the Pre-Amp output can also be installed in power amplifiers, playing the role of a "splitter".

— Subwoofer. The presence in the amplifier design of a separate subwoofer output. Usually, such an output uses an RCA connector (see "Input to the amplifier (Main)"), and the function itself is implemented through a crossover, which selects the low-frequency range in the signal and redirects it to a subwoofer. The "own" output makes it much easier to connect a subwoofer : it does not require any additional equipment, the amplifier itself is enough. This usually provides for the possibility of working with any type of subwoofer — both passive and active; however, in the first case, you will need an additional external amplifier.

— Coaxial S/P-DIF. The presence in the design of the amplifier of the S / P-DIF output of an electric typ...e, with signal transmission via a coaxial cable. For more information about this interface, see the relevant paragraph in the "Inputs" section.

— Optical. The presence in the design of the amplifier output for transmitting a digital audio signal over a fiber optic cable TOSLINK. For more information about this interface, see the relevant paragraph in the "Inputs" section.

— Jack (6.35 mm). Presence of TRS type outputs in the design of the amplifier. These outputs are jacks for 6.35 mm Jack plugs and may look like the corresponding headphone jack (see below). However, this similarity is misleading: TRS produce sound on the principle of "one channel per plug" (an exception may be information amplifiers). This type of Jack connector is found mainly in high-end professional amplifiers.

— Speakon. An interface used in professional audio equipment to connect acoustics to a power amplifier. It has become widespread in high power equipment, including concert amplifiers (see "Intended Use"), due to its increased reliability and suitability even for working with very powerful audio signals. But in household appliances it is rarely used.

— Control output (IR). The control output allows the amplifier's built-in IR receiver to be used to control other components in the audio system, such as a DVD player in another room, out of range of the remote control, from the remote control. With this scheme of operation, the amplifier actually plays the role of a remote sensor, receiving commands and transmitting them through the control output to another device. Note that the very presence of such inputs and outputs does not guarantee the compatibility of various devices, especially if they are produced by different manufacturers; Sharing details should be clarified in the official documentation.

The number of REC outputs in the design of the amplifier. This output is a kind of line interface designed to output sound to a recording device; one of its features is a constant signal level. Since RCA connectors are usually used for connection (see “Amplifier Input (Main)”), a pair of connectors is counted as one REC output — this is the only way to ensure stereo sound transmission.

— Display. The presence of a display on the front panel of the amplifier. Such displays may have a different design and size, but they are all used to display service information: operating mode, selected signal source, special notifications, overload messages, errors, etc. This provides additional ease of use.

— Indicators. In this case, it means that there are indicators on the front panel that indicate the currently used signal source. Usually they look like a row of light bulbs with the appropriate signatures — "Phono", "CD", "Tuner", "AUX", etc. Such pointers are not as versatile as the display, but they are still very convenient.

— Arrow indicators. Presence on the front panel of indicators in the form of scales with arrows. Usually, such indicators are designed to display the peak level of the output signal. They make it easy to track overloads, and many users find this option more convenient and visual than displays. In addition, the arrow scales give the amplifier a stylish appearance, and, unlike the same displays, do not have complex electronics that can distort the sound. However, this category also includes other types of indicators with scales; some of them may not use an arrow, but other indicators (for example, light ones).

— Regulators behind a hidden panel. The presence of a cover on the front panel that hides the controls of the amplifier. Many models are e...quipped with additional controls on the front panel; they can be used to adjust both the sound — volume, bass / treble, balance, etc. — and other operation parameters (for example, selecting a signal source or switching between the main and additional speakers). Sometimes these controls (as well as the front panel inputs) are provided with a cover, usually for aesthetic reasons. an abundance of small elements would give the device a sloppy appearance. The cover can also perform protective functions — for example, it reduces the amount of dust that enters the connectors.

— Input audio jack. The presence on the front panel of an input for connecting an audio signal — usually linear, in analogue format. On the one hand, such an input greatly simplifies work with signal sources that need to be connected only occasionally and for a short time — for example, MP3 players: the front panel is always in sight, while getting to the connectors on the back is sometimes very difficult. On the other hand, usually the role of the front audio jack is played by AUX IN with a 3.5 mm mini-Jack jack. This connector is not used among the main inputs, but it is quite popular in portable electronics, in particular, the players already mentioned. Some models may have a pair of RCA jacks on the front panel (see "RCA (pair)"), but this option is less common.

— Headphone output. Headphone output on the front panel of the amplifier. Headphones are portable devices, and on average you have to reconnect them significantly more often than most other components of the audio system; the output located on the front panel greatly simplifies the process.

— Bass adjustment. The presence in the amplifier of a separate low-frequency level control, in other words, bass volume. The ratio of low and high frequencies largely determines the overall picture of the sound; the optimal options for this ratio for different cases will be different, and they depend on a number of factors — from the type of audio being played to the personal tastes of the listener. Anyway, the bass control provides an additional opportunity to fine-tune the sound of the entire system. It is often combined with a treble control (see below); in fact, this combination is the simplest version of the equalizer.

— Treble adjustment. The presence in the amplifier of a separate volume control for high frequencies. The meaning of this function is completely similar to the bass control described above, only it works with a different frequency band.

— Balance adjustment. The presence in the amplifier of adjusting the balance between the channels. This setting is used in stereo sound: by changing the position of the knob, you can increase the volume for one channel and decrease it for another. Due to this, the conditional centre of the perceived sound shifts towards the speaker that sounds louder. This feature can be very useful for correcting the sound stage — for example, if the speakers have different sensitivity, badly placed, or the signal itse...lf is not properly balanced. At the same time, the balance controller introduces additional elements into the design, which increases the likelihood of interference. And therefore, in top-class amplifiers, it may not be provided at all.

— Adjustment of input sensitivity. Ability to change the input sensitivity of the amplifier; For details on this parameter, see "Input Sensitivity (Line Input)". Also note here that the adjustment itself can be useful when working with several sound sources: it allows you to easily reconfigure the amplifier for each of these sources in order to provide the desired output power level and at the same time avoid distortion.

— Level adjustment. The presence in the amplifier of its own level control, in other words, a system that allows you to change the volume of the sound (by changing the actual output power). In modern home amplifiers (see above), this adjustment is common to all channels, and it is responsible for the actual volume; sometimes using the control on the amplifier is more convenient than on another component of the audio system. But in concert models, each channel, usually, is equipped with its own regulator, thanks to which there are many opportunities for fine-tuning the sound to a specific situation.

— Loudness. This function allows you to adjust the tone of the sound at a low volume. Its necessity is connected with the fact that the human ear perceives a quiet sound differently than a loud one; because of this, even high-quality sound at low volume will seem “blurry”, not clear enough. Loudness corrects this by boosting certain frequencies. Usually this mode is enabled by the user at will.

— Direct connection ( By-pass/Direct). The ability to turn on the amplifier in By-pass / Direct mode. Its name is due to the fact that the signal is sent directly to the amplification stages, bypassing all additional controls (timbre, balance, etc.). Power amplifiers (see "Type"), by definition, use just such a scheme of operation. In integrated models, direct connection not only minimizes distortion in the processed signal, but also provides the sound closest to the original, which allows demanding listeners to appreciate the skill of sound engineers.

— Automatic power off. This function ensures that the amplifier automatically turns off if no signal is received from its input for a certain period of time. In this way, downtime is avoided — for example, if the owner left on business, forgetting to turn off the audio system. And considering that many modern amplifiers require a lot of energy even “at idle”, the savings can be quite significant. It is worth clarifying that in this case we are usually not talking about a complete shutdown, but about switching to standby mode; but the power consumption (see below) in this mode is usually so small that in fact the difference is practically not noticeable.

— MM phono stage. The presence of a phono stage in the amplifier for working with turntables equipped with MM type pickups (with a moving magnet). The phono stage itself is a mandatory attr...ibute of models with a Phono input (see "Inputs"); its necessity is due to the fact that the signal from the pickups for vinyl has specific characteristics and needs additional processing. At the same time, two types of pickups can be used in modern record players — the already mentioned MM plus MC (with a moving coil), each with its own signal characteristics. Therefore, for the normal operation of the turntable, you will anyway need a phono stage of the appropriate type. Such equipment is also available as separate devices, but it is usually easier and cheaper to buy an amplifier with a built-in phono stage.

— MS phono stage. The presence of a phono stage in the amplifier to work with turntables equipped with MC type pickups (moving coil). For more information about this function, see the subsection “MM Phono Stage” above.

— Limiter. The presence of a limiter in the amplifier — a device that limits the dynamic range of the processed signal. This device is also called an "audio signal compressor" (due to the fact that it "compresses" the dynamic range). In simpler terms, a limiter essentially reduces the difference between the quietest and loudest sound output from an amplifier. This feature can be useful in any situation where you have to deal with uneven sound volume. For example, a limiter can make it more comfortable to listen to a symphony that has large volume differences — so that the listener can access the slightest nuances of sound and at the same time, loud fragments, as they say, do not beat on the ears. And for professional concert activity, the presence of a compressor is almost mandatory — in particular, to compensate for changes in volume that occur when the distance from the microphone to the acoustic instrument or the vocalist's mouth changes. Of course, the limiter can also be made as a separate device; however, its presence in the amplifier itself is sometimes more convenient. At the same time, this function is complex and expensive, and therefore is found mainly in professional equipment and top-class consumer models.

— Connecting an additional speaker. The ability to connect an additional set of speakers (one or more) to the amplifier. Note that we are not talking about individual speakers, but about sets designed to work with full-length sound. In other words, if such an amplifier produces sound in stereo format at the main outputs (see "Number of channels"), then an additional set of acoustics will be able to work in this format. Models with this function are designed primarily for situations where you need to output sound to several rooms, and the signal can go either to all sets at once, or only to one at the user's choice. Also, an additional set of connectors can be used for Bi-Wiring (see below).

— Biwiring. Amplifiers with this feature use two separate channels of amplification for bass and treble, and are able to output each frequency band through a separate set of connectors. Due to this, it is possible to apply low-frequency and high-frequency signals via separate wires, and directly to the corresponding specialized speakers of the speaker system — instead of outputting a common signal to it and dividing it into frequencies using the built-in speaker crossover. In fact, this means that the Bi-Wiring connection reduces the likelihood of interference and improves the sound quality. However, keep in mind that this will require not only an amplifier, but also speakers that support this function. Note that Bi-Wiring is usually combined with the ability to connect an additional speaker described above.

— Management of external devices. The ability to use the amplifier as a control device for other components of the audio system — for example, preamplifier, turntable, etc. Control is usually carried out from the universal remote control supplied with the amplifier, and the control signal is transmitted through special connectors — this is much more convenient than adjusting each component separately. On the other hand, the construction of such systems is possible only from devices of the same manufacturer — different companies use different control standards, in most cases they are not compatible with each other.

— Bluetooth. A wireless communication technology with a range of about 10 m (more "long-range" versions are not used in amplifiers), originally created for direct connection between various devices. The functionality of such a connection may be different, but in this case, most often it is possible to broadcast to the sound amplifier from an external device — for example, a smartphone or laptop. However, other functions may be provided, for example, remote control from a mobile gadget through a special application.

— Emergency notification. The ability of the amplifier to work in an emergency warning system, more precisely, the availability of special functions and tools for working in such systems. Such tools may include, for example, connecting to fire detectors and automatically triggering warnings or evacuation messages to areas where the detectors have been triggered; selection of message type depending on the triggered sensor; connecting the notification microphone to the “priority input” and muting all other channels when sound is received from the microphone, etc. A specific set of features should be specified separately. Specialized security units may also be responsible for these functions, but sometimes it is more convenient to use an amplifier with built-in support for emergency notification.