Comparison Behringer HA400 vs Behringer MA400

Frequency range supported by the output amplifier; in other words, the range that this model is capable of delivering to headphones or another analogue audio device.

Theoretically, the wider the frequency range — the richer the sound of the amplifier, the lower the likelihood that the lower or upper edge of audible frequencies will be “cut off”. However, when evaluating this parameter, several nuances should be taken into account. Firstly, the average person is able to hear frequencies from 16 to 22,000 Hz, and with age, these boundaries gradually narrow. However, headphone amplifiers often have wider operating ranges, and they are very impressive — for example, for some models, a set of frequencies from 1 Hz to 60,000 Hz, or even up to 100,000 Hz, is claimed. Such characteristics are a kind of "side effect" from the use of high-end sound processing circuits; from a practical point of view, these numbers do not make much sense, but they are an indicator of the high class of the amplifier and are often used for advertising purposes.

The second nuance is that any headphones also inevitably have their own frequency limitations — and these limitations can be more significant than in an amplifier. Therefore, when choosing, it's ok to take into account the characteristics of the headphones: for example, you should not specifically look for an amplifier with an upper frequency limit of the full 22 kHz, if in the headphones that you plan to use with it, th...is limit is only 20 kHz.

In conclusion, also note that an extensive frequency range in itself does not guarantee high sound quality — it largely depends on other factors (frequency response, distortion level, etc.).

The coefficient of harmonic distortion that occurs during the operation of the amplifier.

Any electronic circuits are inevitably subject to such distortions, and the quality and reliability of the sound at the output depends on their level. Accordingly, ideally, the harmonic coefficient should be as low as possible. So, as a general rule, a level of 0.09% and below (hundredths of a percent) is considered good, and a level of less than 0.01% (thousandths of a percent) is excellent. The exception is lamp devices: higher values \u200b\u200bare allowed in them (in tenths of a percent), however, this point in many cases is not a drawback, but a feature (for more details, see "Lamp").

It is also worth noting that a low harmonic coefficient is especially important when using the amplifier as part of multicomponent audio systems — for example, when listening to music from a vinyl player with an external phono stage. The fact is that in such systems the sum of distortions from all components affects the final sound — and it, again, should be as low as possible.

Types of inputs provided in the design of the amplifier.

Modern headphone amplifiers can be equipped with audio inputs of both analogue ( mini-Jack 3.5 mm, Jack 6.35 mm, RCA, XLR) and digital formats (S / P-DIF with coaxial or optical connection), as well as USB OTG and USB type ports b. Here is a more detailed description of each of these inputs:

— Mini-Jack (3.5 mm). One of the most popular modern audio connectors. In this case, it is mainly used to connect to an analogue audio signal amplifier; this can be a line-level signal or sound from the headphone output from an external device (these nuances should be specified separately), while the connector itself most often has a classic three-pin format and is responsible for both stereo channels at once. Due to its small size, the mini-jack is very convenient for use in portable models (see "Type"). On the other hand, it is less noise-resistant than a 6.35 mm Jack of similar design, and has less extensive capabilities — in particular, it is almost never used for balanced connection. Therefore, in stationary models, this interface is much less common.
Separately, we note that other types of inputs can also be built into the 3.5 mm...type hardware port — for example, coaxial and/or optical (see below for details). However, the presence of a mini-jack is indicated only if this connector is capable of operating in a traditional analogue format.

— Jack (6.35 mm). An audio connector, in many ways similar to the mini-jack described above — in particular, it is also used mainly for connecting an analogue audio signal. The key difference is in the larger sizes. Because of this, Jack type inputs are used much less frequently, and mainly in stationary technology (see "Type"); but, on the other hand, a large diameter expands the possibilities of the connector. First, the connection is more reliable than 3.5mm jacks, with less chance of interference and accidental disconnection. Secondly, such inputs can even be used for balanced connection (although such a possibility is far from mandatory, moreover, XLR connectors are more often used for balanced connection; see below about them and about a similar connection format). Therefore, for high-quality stationary equipment, such inputs are considered more preferable than mini-jack.

— RCA. RCA is technically a type of connector that can be used for a variety of purposes. However, in this case, a very specific application is implied — in the format of a line input (for an analogue audio signal). In this format, one physical connector is responsible for one channel of sound, so this type of input usually consists of a pair of jacks — for the left and right channels. In general, linear RCA is practically not used in portable devices, but it is very popular in stationary audio equipment. It is somewhat inferior to more advanced standards (like XLR, see below) in terms of functionality and noise immunity, but this interface is often quite enough for both everyday and simple professional use.

— XLR. Initially, XLR is a connector of a characteristic round shape, with a set of contacts in the form of pins (and sockets for them) and an additional retainer on the outer ring. It can have a different number of contacts and be used in different formats. However, in headphone amplifiers, when talking about XLR inputs, they usually mean an interface for balanced connection of an analogue (line) audio signal. Such an interface usually consists of at least a pair of three-pin connectors — one for each stereo channel (a rarer option is one common six-pin connector, in fact a two-in-one version). As for the balanced connection, this is a special format that uses three wires per channel (instead of the standard two) and a special way to process the signal at the input. Due to this method, interference due to third-party interference in the connection cable is mutually canceled when it enters the amplifier; in fact, the cable itself plays the role of a noise filter. This allows you to work even with fairly long wires without compromising the purity of the sound. On the other hand, XLR connectors are quite large, and balanced format support affects the cost of the device. Therefore, in general, this interface is considered professional, it is installed in amplifiers of the appropriate level, mostly stationary (with rare exceptions).

— Coaxial S/P-DIF. A variation of the S/P-DIF interface that uses an electrical cable (as opposed to the optical cable described below). In general, the S / P-DIF format allows you to transmit several channels of sound through one connector at once, including working with multi-channel formats (although stereo is most often used in headphone amplifiers). And the electrical version of this interface is somewhat cheaper than the optical one and does not require special care when handling the cable. Its disadvantage is some susceptibility to electromagnetic interference, however, to compensate for this moment, the cable is usually made shielded.
Note that the S / P-DIF coaxial input most often uses an RCA jack as a hardware connector. However, this interface should not be confused with the analogue RCA described above: these are fundamentally different standards that are not compatible with each other. In addition, in some models (in particular, portable ones), this type of input can be physically combined with a 3.5 mm jack; in this case, one socket can work in different formats (depending on the selected settings), and a cable with a special connector (or an appropriate adapter) is required to use the coaxial interface.

— Optical S/P-DIF. A variation of the S/P-DIF interface that uses a TOSLINK fibre optic cable to transmit digital audio in stereo or multi-channel format (however, the latter is not typical for headphone amplifiers). The main advantage of such a connection over the coaxial one described above is complete insensitivity to electromagnetic interference. On the other hand, the optical cable is quite delicate, it does not tolerate strong pressure and bending.
It is worth saying that in some amplifiers — especially portable ones — the optical input can be built directly into the 3.5 mm jack, and to work with such an input, you need a cable with a plug of the appropriate design. The connector itself can work in different formats — depending on the settings and the connected cable.

— USB (OTG). Initially, USB OTG is a standard that allows you to connect various USB peripherals (such as flash drives) to portable gadgets like smartphones or tablets. However, in headphone amplifiers, this function has its own specifics, it should be specified separately in each case. So, most models with USB OTG are portable, and in them this input is used in the classic format — to receive a digital audio signal from microUSB, USB-C or another similar connector in a portable gadget (if the gadget initially provides such an opportunity). But in stationary amplifiers (see "Type"), the name "USB OTG" can denote an interface for connecting to a PC, if this interface does not use USB Type B, but another type of connector. These nuances should be clarified separately.

— USB (Type B). Interface for connecting the amplifier to the USB port of a computer and transmitting sound in digital form; in other words, a connector for using the amplifier as an external sound card. Formally, USB Type B is a strictly defined type of USB connector that has a characteristic square shape; it is this connector that is usually installed in stationary models. But in portable devices, this role can be played by ports of a different type — for example, microUSB; however, they are also referred to as USB Type B in such cases.

Anyway, the point of connecting an amplifier in the format of an external sound card is, first of all, that the built-in sound cards of modern computers usually have rather modest characteristics, and much better sound can be achieved on external equipment.

Types of additional outputs provided in the design of the amplifier.

We emphasize that in this case we are talking about additional outputs — that is, connectors that are NOT intended for connecting headphones (although these outputs can use the same types of connectors). The presence, type and number of headphone jacks are indicated separately in the specifications (see below — "Mini-Jack outputs (3.5 mm)", "6.35 mm outputs (Jack)", "XLR outputs", "Headphone outputs"). Additional outputs are usually analogue audio interfaces ( mini-Jack 3.5 mm, Jack 6.35 mm, RCA, XLR) or digital format (S/P-DIF in coaxial or optical design). Here is a more detailed description of each of these interfaces:

— Mini-Jack 3.5 mm. Perhaps the most common analogue audio connector nowadays. Among other things, it is widely used as a linear audio output — in particular, for connecting computer speakers and portable acoustics. There are several varieties of mini-jack, but headphone amplifiers usually use a traditional three-pin jack for transmitting stereo sound through a single connector as an additional output. Anyway, the connector itself is small and convenient for use in compact technology; however, in terms of functionality, reliability and connection quality, it is infer...ior to its “big brother” Jack 6.35 mm. Therefore, the presence of additional 3.5 mm mini-jack outputs is typical mainly for portable amplifiers (see "Type"), as well as for individual stationary models designed for compactness.
Separately, we note that other types of inputs can also be built into the 3.5 mm type hardware jack — for example, coaxial and/or optical (see below). However, the presence of a mini-jack is indicated only if this connector is capable of operating in a traditional analogue format.

— Jack (6.35 mm). An analogue of the 3.5 mm mini-Jack described above, which is used mainly in stationary audio equipment — this is due to the large size of this connector (although there are also portable models with additional outputs of this format among headphone amplifiers). However, such dimensions provide a number of advantages: in particular, the connection is more reliable and noise-resistant. In addition, it is quite possible to implement even a balanced connection through a 6.35 mm Jack (for more details, see “XLR” below), although this functionality is relatively rare in headphone amplifiers — the standard format of operation is used much more often, with the transmission of both channels of stereo sound through one 6.35 output mm.

— RCA. RCA is technically a type of connector that can be used for a variety of purposes. However, in this case, a very specific application is implied — in the line-out format (for analogue audio). In this format, one physical connector is responsible for one channel of sound, so this type of output usually consists of a pair of connectors — for the left and right channels. As for use, linear RCA will be convenient primarily for connecting the amplifier to various stationary audio equipment, mainly entry-level and mid-level. This interface itself is not particularly noise-resistant, however, with the proper quality of the connecting wires, it is quite capable of providing more than decent sound quality — quite sufficient not only for everyday use, but also for relatively uncomplicated professional use.

— XLR. The XLR connector has several varieties, differing in the number of contacts; however, all of them have contacts in the form of characteristic pins ("pins") and a round rim, complemented by a separate latch for maximum connection reliability. And as an additional audio output in headphone amplifiers, a three-pin XLR version with balanced connection support is most often used. Such an interface outputs a line-level analogue signal on a "one channel per connector" basis; so an XLR output usually includes at least two hardware jacks, stereo left and right. As for the balanced connection, this is a special format that uses three wires per channel (instead of the standard two) and a special way to process the signal at the receiver input. Due to this, interference arising from third-party interference in the connection cable is mutually canceled when it arrives at the receiver; in fact, the cable itself plays the role of a noise filter. This allows you to work even with fairly long wires without compromising the purity of the sound. On the other hand, the XLR connectors themselves are quite large, and the support for a balanced format affects the cost of the device. Therefore, in general, this interface is considered professional, it is installed in amplifiers of the appropriate level, and only stationary ones — it makes no sense to use additional outputs of this type in portable models for a number of reasons.

— Coaxial S/P-DIF. A variation of the S/P-DIF interface that uses an electrical cable (as opposed to the optical cable described below). The common features of all varieties of S / P-DIF are, firstly, the digital signal format, and secondly, the ability to transmit stereo or multi-channel sound over a single connector. Specifically, the coaxial version uses a shielded electrical cable; it does not have one hundred percent protection against interference, but it is cheaper than fibre optic and does not require special delicacy in handling. As for the application, it makes sense to look for a device with an S / P-DIF output (of any format) if you plan to use it to switch a digital signal — for example, broadcasting sound from a smartphone's microUSB port to the coaxial input of an external audio receiver. Such use in the case of headphone amplifiers is quite exotic, so outputs of this type have not received much distribution.

— Optical S/P-DIF. A variation of the S/P-DIF interface that uses a TOSLINK fibre optic cable. See above for more on S/P-DIF in general and its use in headphone amplifiers. Also note here that an optical cable requires more careful handling than coaxial, but it is practically not subject to electromagnetic interference, since light pulses are responsible for signal transmission in this case.

The total number of headphone outputs provided in the design of the amplifier.

Most modern headphone amplifiers are designed for individual use, but there are exceptions — you can find models for sale with 2 outputs and even 3 or more. The general essence of this design is obvious: it allows you to connect several headphones at once and use the amplifier for several listeners at once.

However, not all connectors can be of the same type. Among those there are classic mini-Jack (3.5 mm) and Jack (6.35 mm), as well as less popular balanced 2.5 mm micro-Jack, XLR and 4.4 mm Pentaconn.

— mini-Jack (3.5 mm). The most popular plug format among modern wired headphones. It is found in models of all price categories; and even high-end solutions that can be used with a more advanced 6.35 mm Jack, most often do not have a built-in Jack format connector, but a 3.5 mm plug and a complete 6.35 mm adapter. On the other hand, the acoustic properties of the mini-Jack are somewhat inferior to the "big brother"; therefore, this headphone connection format is found mainly among portable models (see "Type"), although there are also stationary amplifiers with such outputs.

— 6.35 mm (Jack). Plug format designed mainly...for fairly advanced technology, mostly stationary. The large size of the connector somewhat complicates its use in compact devices; on the other hand, due to this feature, the connection quality, reliability and noise immunity are much higher than that of the smaller 3.5 mm mini-Jack. And you can connect headphones with a mini-Jack plug to a Jack-type jack using a simple adapter; often such an adapter is even supplied with “ears”. Thus, 6.35 mm type outputs are found in most stationary amplifiers (see "Type") and are found even in some portable models.

— XLR. This connector is mainly for professional use, having a characteristic round shape, contacts in the form of pins (“pins”), and often also a latch on the rim for additional reliability in connection. This connector is used for the so-called balanced connection of headphones, which has a positive effect on the purity of the sound and allows you to use even long wires without additional risk of distortion. On the other hand, in the case of headphones, the need for such a connection arises relatively rarely, and there are not many "ears" themselves with an XLR plug — mostly high-end professional models. So in amplifiers, outputs of this type are mainly used in stationary devices (see "Type") of a premium level. Most often, a four-pin connector is used as such an output, often without a latch and/or reduced sizes. In general, in audio equipment, such a connector is less common than a three-pin one (see "Outputs"), but specifically in headphones it is the standard option — especially since 4 pins allow you to output both stereo channels through one jack (whereas three-pin jacks work in the format "one channel per plug"). However, there are amplifiers where a pair of three-pin XLRs plays the role of a balanced headphone output. At the same time, such connectors can be physically combined with 6.35 mm Jack outputs — in other words, a 6.35 mm jack is built right into the centre of the XLR connector. This makes the design more compact, but does not allow the use of both types of connectors at the same time.

— Pentaconn 4.4. Connection implemented by a 5-pin connector with a diameter of 4.4 mm. This is a relatively new balanced connection standard developed by Sony. Most often used as a line output for digital-to-analogue converters and amplifiers. Additionally, this connector can be found in multimedia players and even console consoles. The main advantage of the Pentaconn 4.4 standard is the ability to output an audio signal to sufficiently powerful high-impedance headphones. This standard is an alternative for not very practical Jack and XLR connections.