Comparison Cambridge CXA81 vs Cambridge Azur 350A

The maximum number of channels the amplifier can handle. The choice for this parameter depends primarily on the intended format of using the device.

Most modern amplifiers have two channels for normal stereo sound, which is enough for listening to music or radio programs. There are also models designed for multi-channel "surround" sound, but they are much less common. This is due to the fact that such sound is most often used as an accompaniment to high-quality video — and therefore a home theater receiver is usually used for processing, rather than a separate audio amplifier.

Among the top-class models, there may be single-channel amplifiers — they provide maximum opportunities for fine-tuning the sound, but you have to purchase several such devices, one per channel. Another specific variety is amplifiers designed to add a certain number of channels to those already available; the most popular of these options is 3-channel, capable of turning an existing stereo system into a multi-channel one.

The range of audio frequencies that the amplifier is capable of handling. The wider this range, the more complete the overall picture of the sound, the less likely it is that too high or low frequencies will be “cut off” by the output amplifier. However, note that the range of sound audible to a person is on average from 16 Hz to 20 kHz; There are some deviations from this norm, but they are small. At the same time, modern Hi-Fi and Hi-End technology can have a much wider range — most often it is a kind of "side effect" of high-end circuits. Some manufacturers may use this property for promotional purposes, but it does not carry practical value in itself.

Note that even within the audible range it does not always make sense to chase the maximum coverage. It is worth, for example, to take into account that the actually audible sound cannot be better than the speakers are capable of giving out; therefore, for a speaker system with a lower threshold of, say, 70 Hz, there is no need to look for an amplifier with this figure of 16 Hz. Also, do not forget that a wide frequency range in itself does not absolutely guarantee high sound quality — it is associated with a huge number of other factors.

The nominal sound power output by the amplifier per channel when operating with a load having a dynamic resistance (impedance) of 8 ohms. In our catalog, this parameter is indicated for the mode when all channels of the amplifier work under load (see "Number of channels"); in the presence of unused channels, the rated power may be slightly higher, but this mode cannot be called standard.

Rated power can be simply described as the highest output signal power at which the amplifier is able to work stably for a long time (at least an hour) without negative consequences. These are average figures, because in fact, the audio signal is by definition unstable, and individual level jumps can significantly exceed the rated power. However, it is she who is the main basis for assessing the overall loudness of the sound.

This indicator also determines which speakers can be connected to the amplifier: their rated power should not be lower than that of the amplifier.

According to the laws of electrodynamics, with different dynamic load resistance, the output power of the amplifier will also be different. In modern speakers, the standard values \u200b\u200bare 8, 6, 4 and 2 Ohms, and power levels are indicated for them.

The nominal sound power output by the amplifier per channel when a load with a dynamic resistance (impedance) of 4 ohms is connected to it. See Power per Channel (8Ω) for more information on power rating and its relationship to impedance.

In itself, the signal-to-noise ratio is the ratio of the level of pure sound produced by the amplifier to the level of extraneous noise that occurs during its operation. This parameter is the main indicator of the overall sound quality — and very clear, because. its measurement takes into account almost all the noise that affects the sound in normal operating conditions. A level of 70 – 80 dB in modern amplifiers can be considered acceptable, 80 – 90 dB is not bad, and for advanced audiophile-class devices, a signal-to-noise ratio of at least 100 dB is considered mandatory.

If the specifications do not specify for which output the signal-to-noise ratio is indicated, it usually means its value for the linear input (see "RCA (par)"). This is quite enough to evaluate the quality of the device for this parameter. However, some manufacturers indicate it for other inputs — Main, Phono; see below for more on this.

The damping factor describes the quality of interaction between the amplifier and the speaker system connected to it.

Due to the design features, any speaker is prone to the occurrence of so-called parasitic oscillations — oscillations that continue after the main impulse from the amplifier has ceased (similar to how a string continues to vibrate after a pluck). This phenomenon has a negative effect on sound quality, and manufacturers use various means to reduce it to an absolute minimum; suppression of parasitic oscillations is called damping.

The most effective type of damping is electrical, by reducing the output impedance of the amplifier. The lower this resistance, the better the amplifier keeps the speakers from unnecessary vibrations. To evaluate this effect, they introduced the concept of “damping factor” (damping factor) — the ratio of the load resistance (impedance) to the output resistance of the amplifier. The minimum value of such a coefficient for Hi-Fi class equipment is 20; indicators at the level of 100 – 120 can be called good, and among the Hi-End segment there are numbers of the order of several thousand.

At the same time, it is worth noting that when increasing to three-digit numbers, the original meaning of this parameter is, in fact, lost, and other points appear. The most important of them from a practical point of view is that models with a high damping factor are very demanding on the quality of the connection to t...he speakers — the high resistance of cables and connectors can negate the damping properties of the amplifier itself. There are other nuances associated with this indicator (in particular, recommendations for choosing an amplifier and speakers for each other); they are described in detail in specialized sources.

The sensitivity and dynamic impedance of the amplifier when a signal is applied to the RCA line input.

Under the sensitivity of any input (except optical) is meant the lowest signal voltage at this input, at which the amplifier is able to provide normal nominal power values (see "Power per channel (8Ω)"). This parameter determines, first of all, the requirements for the signal source. On the one hand, the voltage provided by this source must not be lower than the input sensitivity of the amplifier, otherwise the latter simply will not give the claimed characteristics. However, a significant excess in voltage should not be allowed, otherwise the sound will begin to be distorted. More detailed recommendations on choosing an amplifier by sensitivity are described in special sources.

For any input other than optical, it is believed that the higher this indicator, the less distortion the amplifier introduces into the signal. The minimum level of input impedance in modern models is considered to be 10 kOhm, and in high-end devices it can reach several hundred kOhm.

— Euroblock. Analogue audio input (usually line level) using a Euroblock connector. This connector, used mainly in professional audio equipment, is remarkable in that it is attached to the wire using terminals. This is extremely convenient when working with stripped wires (which is often required in professional applications): screwing such a wire to the plug once and connecting / disconnecting the plug to the Euroblock connector is much easier than constantly unscrewing / screwing the terminals. In addition, such a connection is often made balanced (see "XLR (balanced)" below). Inputs of this type are found mainly in information and information-concert amplifiers (see above).

— Phono. Dedicated input for connecting to the amplifier turntables; often has a suffix indicating the type of cartridge that is compatible, such as "Phono MM" or "Phono MM/MC" (see "Advanced — Phono Stage" for details). Despite the proliferation of digital formats, these players are still highly regarded by audiophiles for their high quality and fidelity, and are often used in premium audio systems. However, connecting a "turntable" has its own characteristics — in particular, it requires a phono stage (for more details, see ibid.) — and standard inputs are unsuitable for this purpose. Therefore, a Phono jack is a must if you want to connect your turntable directly, without an external phono stage.

— USB B. The USB interface is widely used in com...puter technology for various peripherals. The presence of a type B input means that the amplifier can be connected to a computer as an external controlled device (slave). Most often, with this connection, it is used as an external sound card or audio interface — this provides higher sound quality and more extensive options for its settings than most built-in sound cards, even expensive ones. However, the matter is not limited to this: in some models, via USB type B, you can update the firmware or change the special parameters of the amplifier.

— Coaxial S / P-DIF. Digital audio input, a variation of the S/P-DIF interface based on a conventional electrical signal (the second variation, optical, is described below). Usually uses a common RCA connector, known as a "tulip", but has rather strict cable requirements. The bandwidth of any version of S / P-DIF is quite sufficient even for high-quality multi-channel sound, and the coaxial version itself is simpler, cheaper and more reliable than the optical one, but more susceptible to interference.

— Optical. Input for transmitting digital sound using light signals, via TOSLINK fiber optic cable; one of the versions of the S/P-DIF standard. The main advantage of optical fiber over traditional electrical cables is complete insensitivity to electrical interference; at the same time, it is more expensive and requires rather careful handling (in particular, it does not tolerate sharp bends).

— Balanced digital ( AES/EBU). The AES/EBU interface is used in the professional field to transmit audio in digital format. It can use several connection types; in this case, it means transmission over the so-called balanced line using an XLR connector. Both the principle of balanced connection and the connector itself are described in detail in the “XLR (balanced)” section below — however, in the case of AES / EBU, we are talking about a digital signal, not an analogue signal.

— COM port ( RS-232). A connector used to control the amplifier from a computer. Through it, you can change the settings, incl. and quite thin, and in some models even update the firmware. Usually, for such purposes, special software is required, which can be supplied with the amplifier.

— Control input (IR). Connector for connecting an external infrared remote control receiver. When properly placed, such a receiver will allow you to use the remote control even in places where the signal from the remote control cannot reach the main (built-in) sensor — for example, in another room. For such purposes, not only sensors can be used as a separate device, but also system components that are compatible with the remote control — for example, players or tuners.

The number of line inputs in the amplifier design using the RCA interface. Unlike the Main input (see above), which can work with the same connectors, when connected to a linear RCA, the signal goes through all the stages of processing provided for in the amplifier — for example, adjusting the balance or frequencies (see "Adjustments"), etc. .P.

See “Amplifier Input (Main)” for details on the connector itself. Here we note that when using RCA as a linear interface, a pair of such connectors is considered one input. This is due to the fact that only one channel can be transmitted over one coaxial cable, so a pair is needed to work with stereo sound.

The number of signal inputs (of any type) determines how many signal sources can be simultaneously connected to the amplifier. Accordingly, it is worth choosing a model according to the number of inputs, taking into account the expected number of such sources: after all, it is easier to connect them all and select them through the amplifier’s remote control or control panel than to fiddle with reconnecting every time.