Passmark CPU Mark
The result shown by the laptop processor in the Passmark CPU Mark test.
Passmark CPU Mark is a comprehensive test that is more detailed and reliable than the popular 3DMark06 (see above). It checks not only the gaming capabilities of the CPU, but also its performance in other modes, based on which it displays the overall score; this score can be used to fairly reliably evaluate the processor as a whole (the more points, the higher the performance).
Drive capacity
The capacity of the drive installed in the laptop. If there are several separate drives (for example, HDD + SSD, see "Drive type") — this item indicates the volume of the most capacious drive (in our example — HDD).
A larger drive allows you to store more data, but it also comes at a higher cost. At the same time, it is worth remembering that the price also depends on the type of media: for example, SSDs are much more expensive than hard drives of the same volume. So it is best to directly compare drives of the same type with each other. As for specific volumes, the most modest figures are typical for configurations with pure solid-state memory — SSD of one type or another or eMMC (see "Drive type"): among them you can find solutions for
240 – 360 GB and even
128 GB or less . Hard drive capacity actually starts at
480 – 512 GB ;
1TB storage capacity is average, and the most capacious modern laptops are equipped with storage
of 2TB or even
more.
M.2 drive interface
The connection interface used by the M.2 SSD installed in the laptop (see "Drive type").
One of the features of the M.2 connector and drives for it is that they can use two different connection interfaces: PCI-E (in one form or another) or SATA. We emphasize that this paragraph indicates the data of the SSD module; the connector itself may provide other interface options, including more advanced ones — see "M.2 connector interface" (for example, a drive with a PCI-E 3.0 2x connection can be placed in a connector that also supports the faster PCI-E 4.0 4x). However, anyway, the connection connector usually allows you to realize all the features of the installed drive; so this item allows you to quite reliably evaluate the capabilities of the standard M.2 module.
As for specific interfaces, nowadays you can mainly find the following options:
— SATA 3. The SATA interface was originally designed for traditional hard drives. The third version of this interface is the latest; it provides data transfer rates up to 600 Mbps. This is significantly less than PCI-E, and in general, very little by the standards of SSD drives. Therefore, M.2 connection using SATA is typical mainly for low-cost entry-level modules. However, even these media are generally faster than most HDDs.
— PCI-E. Universal interface for connecting internal peripherals. Provides generally faster speeds than SATA, making it better suited for SSD modules: theoretically, PC
...I-E allows you to realize the full potential of SSDs, even the fastest. In fact, the supported data transfer rate may be different — depending on the version of the interface and the number of lines (data transmission channels). Here are the options most relevant for modern laptops:
- PCI-E 3.0 2x. Connection using 2 lanes PCI-E version 3.0. This version provides speeds of about 1 GB/s per line; respectively, two lines give a maximum of just under 2 GB / s.
- PCI-E 3.0 4x. Connection using 4 lanes PCI-E version 3.0. Provides a maximum speed of about 4 GB / s.
- PCI-E 4.0 4x. Connection using 4 lanes PCI-E version 4.0. In this version, the throughput, compared to PCI-E 3.0, has been doubled — thus, 4 lines give a maximum speed of about 8 MB / s.
Note that in the case of M.2 connectors, different PCI-E variations are usually quite compatible with each other — except that the connection speed when working with a "non-native" connector will be limited by the capabilities of the slowest component. For example, when connecting a PCI-E 3.0 4x SSD module to a PCI-E 3.0 2x slot, this speed will correspond to the capabilities of the connector, and when connected to PCI-E 4.0 4x, to the capabilities of the drive.NVMe
The presence in the laptop of an SSD-drive with support for NVMe technology (accordingly, the connector where this drive is connected also supports this technology).
NVMe is a data transfer standard designed specifically for SSD storage. It uses the PCI-E bus and allows you to maximize the possibilities of such memory. Initially, it was believed that NVMe makes sense to use mainly on high-performance systems, in particular gaming ones; however, the development and cheapening of technology has led to the fact that this feature is increasingly found in simpler laptops.
Also note that NVMe can be implemented through different hardware connectors. NVMe M.2 SSDs are the most common in laptops (see "M.2 Drive Interface" above), but there are other options — in particular, the ultra-compact U.2 connector.
M.2 connector interface
The interface of the main M.2 connector provided in the laptop.
In this case, the main slot is considered to be the one in which the SSD M.2 drive is installed (see "Drive type"). The interface of the drive itself is indicated separately (see above), and the interface of the connector is specified if the connector supports a more advanced type of connection than the device installed in it. An example is the following situation: the device itself works according to the SATA or PCI-E 3.0 2x standard (see "M.2 drive interface" above), and the connector on the board is capable of working with the PCI-E 3.0 4x interface.
Such information will be useful, first of all, for evaluating the possibilities for upgrading a laptop (with replacing a standard SSD module with a faster one). Nowadays, in this paragraph, you can mainly find the following options:
— PCI-E 3.0 2x. In fact, the most modest PCI-E standard found in M.2 ports of modern laptops: connection using 2 lanes of PCI-E version 3.0. This version provides speeds of about 1 GB/s per line; respectively, two lines give a maximum of just under 2 GB / s.
— PCI-E 3.0 4x. Connection using 4 lanes PCI-E version 3.0. Provides a maximum speed of about 4 GB / s.
— PCI-E 4.0 4x. Connection using 4 lanes PCI-E version 4.0. In this version, the bandwidth, compared to PCI-E 3.0, has been doubled — thus, 4 lines give a maximum speed of about 8 GB / s.
— PCI-E. Connection...via PCI-E, for which the manufacturer did not specify the details (version and number of lines).
Recall that in the case of M.2 connectors, different PCI-E options are quite compatible with each other — except that the speed will be limited by the capabilities of a slower component. In fact, this means that, for example, in an M.2 connector with a PCI-E 3.0 4x interface, it is quite possible to connect a drive for PCI-E 3.0 2x or PCI-E 4.0 4x; in the first case, the speed will be limited by the capabilities of the drive, in the second, by the capabilities of the connector.
Additional 2.5" slot
The presence in the laptop of an additional compartment for an internal drive of the form factor 2.5 ".
Usually, to install or remove a drive in such a bay, it was not necessary to disassemble the entire laptop — just remove the cover or remove the plug. As for 2.5", this is the traditional form factor for hard drives (HDD) for "laptop" purposes, although other types of media (SSD and SSHD — see "Media Type") can be produced in this format. For connection 2.5 "storage drives normally use the SATA connector — it is not as fast as more modern standards like M.2 PCI-E (see "Drive Interface"), however, it is cheaper, and for HDD this connector is quite enough.
Thus, the
presence of an additional 2.5" bay allows you to quickly and cost-effectively increase the total volume of laptop drives.
Additional M.2 connector
The number of
additional M.2 connectors on the laptop motherboard.
In this case, any free M.2 connector is called additional (if there is an installed drive, the connector is considered the main one and its characteristics are given above — see "M.2 connector interface" and so on). There may be
several such free slots — therefore, our catalog specifies the number of additional M.2 connectors, and not just their presence.
Anyway, this parameter will be useful primarily if the laptop is bought for an upgrade. It allows you to estimate how many M.2 SSDs (or other peripherals with such a connection) can be additionally installed in the device. At the same time, when choosing specific components, you should also take into account the interface and the size of free M.2 slots (see below for more details).
Addittional M.2 connectors interface
A connection interface supported by the laptops optional M.2 connector (see above). Recall that this connector is initially free; so this information allows you to evaluate the compatibility with additional components and, accordingly, the possibility of upgrading.
Two main types of interfaces can be implemented through the M.2 connector: SATA and PCI-E. SATA was originally created for hard drives, its support is inexpensive, but the speed of such a connection does not exceed 600 MB / s — this is very low by the standards of SSDs and other modern peripherals. Therefore, in the additional connector (s) M.2, one or another type of PCI-E is most often implemented. This interface has several variations that differ in version, number of lines and, as a result, speed; Here are the options most relevant for modern laptops:
— PCI-E 3.0 2x. Connecting using 2 lanes of PCI-E version 3.0 gives a maximum speed of just under 2 GB / s.
— PCI-E 3.0 4x. Connection using 4 lanes PCI-E version 3.0. Provides a maximum speed of about 4 GB / s.
— PCI-E 4.0 4x. Connected using 4 lanes PCI-E version 4.0, throughput is about 8 Mbps.
— PCI-E. Connection via PCI-E, for which the manufacturer did not specify the details (version and number of lines).
It is worth noting here that in the case of M.2, different versions of PCI-E are quite compatible with each other (except that the speed of work will be limited by the capabilities of the slower side —...the drive or connector). Therefore, even if the specific capabilities of such a connector are not specified, this is generally not critical (these capabilities will not hurt to clarify unless if high performance is fundamentally important to you).
Additional M.2 drive size
The size of an additional slot for a drive (or other peripherals) with an M.2 interface provided in a laptop.
We emphasize that in this case we are not talking about the actually installed drive, but about the size of the bay (recall, there is no drive in it initially — for more details, see "Additional M.2 connector"). Knowing this size, you can estimate the maximum dimensions of the SSD module (or other component) that can fit in this bay. It is worth noting here that the most widespread nowadays are M.2 boards with a width of 22 mm, slots in laptops are usually made for this standard width. Therefore, the main indicator that determines size compatibility is length.
For bays on laptop motherboards, the length is most often 80 mm (marking 22x80 mm). This allows you to install 22 mm M.2 boards with a length of 80 mm, 60 mm, 42 mm and 30 mm — that is, all types of such boards, except for the largest, at 110 mm. The latter, however, is not a disadvantage, since 110-mm components are rarely used in laptops. If there are several additional (free) M.2 slots and they differ in size, these data are also specified in this paragraph, for example, “22x80 / 22x42 mm”.
