Fireplace Accessories

Dripless stove pipe adapters are used to connect single wall stove pipe. These Adapters are designed to slip inside single wall stove pipe to contain any creosote dripping down the chimney to inside t more→he stove pipe.

The insulated wall thimble installs quickly and eliminates the need for using individual fire stops. Interior plate has black matte finish. The round shielding acts as a radiation shield and provides more→the required 2 inch airspace clearance to combustibles.

The DirectVent Pro 4 inches x 6-5/8 inches Galvanized Cathedral Ceiling Support Box is a component that is used in a typical venting installation.

Part of the chimney system roof assembly, the round top is designed with a dome to exclude rain and leaves and a lower skirt to deflect wind for proper chimney draft. In the Type HT chimney (5 inch, 6 more→inch, 7 inch and 8 inch sizes), the round top is designed with three legs that slide down over the outside of the chimney. A cinch band is then positioned over the legs and tightened to hold the top firmly in place. This design makes cap removal for cleaning a breeze. In the ultra-temp and galva-temp chimney (10 inch, 12 inch and 14 inch sizes), the round top is designed with a squeeze collar that fits inside the chimney pipe. The squeeze collar expands as a set screw is tightened to hold the top …

Designed to support a vertical wall installation above the tee or above an offset. It can also serve as an intermediate support.

DirectVent Pro is a complete venting system designed for use with gas direct vent stoves, heaters, and fireplaces.

The damper kit features an attractive outer black enamel finish. The outer wall is constructed from aluminized steel while the inner liner is composed of stainless steel. The combination of these meta more→ls provides a durability that last significantly longer than single wall stove pipe.

This triple wall chimney cap and features two insulating layers consisting of a ceramic blanket plus air space. The ceramic blanket insulation is held securely in position, eliminating hot spots commo more→n with loose-fill type insulations. In the event of a creosote fire, the compressible blanket insulation permits the chimney liner to expand outwardly in a radial direction.

DuraPlus is designed to stay cool on the outside, to provide a hot draft on the inside, to boost stove efficiency and to provide for a fire-safe design that protects both the chimney and the building. more→This triple-wall chimney features two insulating layers (ceramic blanket, plus air space). The ceramic blanket insulation is held securely in position, eliminating hot spots common with loose-fill type insulations. In the event of a creosote fire, the compressible blanket insulation permits the chimney liner to expand outwardly in a radial direction. Designed for normal, continuous operation at 1000 degree Fahrenheit flue gas temperatures, DuraPlus is subjected to rigorous and stringent HT requirements …

The Type HT Wall Support Kit has been tested for use fully enclosed and has been designed in 5 inch, 6 inch, 7 inch and 8 inch to carry up to 60 feet of height. The capacity of the larger sizes, 10 in more→ch, 12 inch and 14 inch, is 40 feet of chimney. Braces may be fastened to the wall either above or below the plate for chimneys which penetrate through the wall.

With proper framing, all ceiling supports assure at least 2 in minimum clearance to combustibles at the support level and can carry up to 50 ft of vertical chimney height.

"This new design gives, the flexibility of securing the 5"", 6"", 7"" and 8"" diameter chimney with a heavy duty band. The band allows to slide the installed length vertically to properly position thi more→s section in the system."

The finish ceiling support (FSP) in 5, 6, 7 and 8 inch sizes, is available with either a round or square trim plate. With proper framing, all ceiling supports assure at least 2 inch minimum clearance more→to combustibles at the support level and can carry up to 50 feet of vertical chimney height.

DuraPlus is designed to stay cool on the outside, to provide a hot draft on the inside, to boost stove efficiency and to provide for a fire-safe design that protects both the chimney and the building. more→This triple-wall chimney features two insulating layers (ceramic blanket, plus air space). The ceramic blanket insulation is held securely in position, eliminating hot spots common with loose-fill type insulations. In the event of a creosote fire, the compressible blanket insulation permits the chimney liner to expand outwardly in a radial direction. Designed for normal, continuous operation at 1000 degree Fahrenheit flue gas temperatures, DuraPlus is subjected to rigorous and stringent HT requirements …

Part of the chimney system roof assembly, the round top is designed with a dome to exclude rain and leaves and a lower skirt to deflect wind for proper chimney draft.

The type HT wall support kit has been tested for use fully enclosed and has been designed in 5 inch, 6 inch, 7 inch and 8 inch to carry up to 60 feet of height. The capacity of the larger sizes, 10 in more→ch, 12 inch and 14 inch, is 40 feet of chimney. Braces may be fastened to the wall either above or below the plate for chimneys which penetrate through the wall.

A roof brace kit can be used whenever there is a need to stabilize the chimney above the roof level. The roof brace kit should be used at a midpoint on the chimney.

The support box is intended for use when installing chimney in an A frame, in a mobile home or in a ceiling under a narrow section of roof. It provides a finished installation at the ceiling level and more→will support up to 20 feet of 6, 7 or 8 inch diameter chimney. The part also provides shielding from insulation when installed in an unoccupied attic space. The support box assembly is comprised of a black box designed for installation inside 16 inch O.C. joists, a cylindrical shield, support bucket, ceiling trim and four screws.

The US Stove Miracle Heat Blower is compatible with wood or coal stoves and furnaces and is designed to improve the efficiency of an older stove or furnace. This blower features an integrated thermo d more→isk that senses the heat in the chimney and once hot, blows air through the heat exchanger to bring up to an extra 10 percent of the heat loss back into the room. Easy to install into a 12 inch section of the stove pipe just above your stove, this blower is ultra quiet and has fully automatic operation.

An economical venting system used for relining masonry chimney for natural gas or liquid propane category I, draft hood equipped appliances, and appliances tested and listed to use Type B Gas Vent for more→a wide range of applications, including: natural gas fireplaces, gas-fired furnaces, boilers, water heaters, and wall or space heating applications. Protects the masonry chimney from damaging effects of flue product condensation. Simpson Dura-Vent has changed their name to DuraVent. DuraVent is a recognized technological leader in the venting industry. Consistently the first to market with new innovations in venting systems, DuraVent has captured a leadership position in emerging markets. DuraVent …

The support box is intended for use when installing chimney in an A frame, in a mobile home or in a ceiling under a narrow section of roof. It provides a finished installation at the ceiling level and more→will support up to 20 feet of 6, 7 or 8 inch diameter chimney. The part also provides shielding from insulation when installed in an unoccupied attic space. The support box assembly is comprised of a black box designed for installation inside 16 inch O.C. joists, a cylindrical shield, support bucket, ceiling trim and four screws.

An ideal support assembly for freestanding fireplaces and open cathedral ceiling installations. Fits all roof pitches and requires only simple framing. Mounts easily on to top of roof through opening more→that allows 2 inch clearance. Maximum length of chimney which can be suspended below is 20 feet supported. Maximum total length is 30 feet. The Roof Support (RSP) contains one 18 inch length of pipe, roof brackets and necessary hardware. The roof brackets and hardware may be purchased without the pipe section by ordering a Roof Support Kit (RSK). The brackets may be assembled to any standard pipe length at any desired height. Locking bands must be used at each pipe joint when installing either the …