Comparison Denon PMA-900HNE vs Denon PMA-720AE

The range of audio frequencies that the amplifier is capable of handling. The wider this range, the more complete the overall picture of the sound, the less likely it is that too high or low frequencies will be “cut off” by the output amplifier. However, note that the range of sound audible to a person is on average from 16 Hz to 20 kHz; There are some deviations from this norm, but they are small. At the same time, modern Hi-Fi and Hi-End technology can have a much wider range — most often it is a kind of "side effect" of high-end circuits. Some manufacturers may use this property for promotional purposes, but it does not carry practical value in itself.

Note that even within the audible range it does not always make sense to chase the maximum coverage. It is worth, for example, to take into account that the actually audible sound cannot be better than the speakers are capable of giving out; therefore, for a speaker system with a lower threshold of, say, 70 Hz, there is no need to look for an amplifier with this figure of 16 Hz. Also, do not forget that a wide frequency range in itself does not absolutely guarantee high sound quality — it is associated with a huge number of other factors.

In itself, the signal-to-noise ratio is the ratio of the level of pure sound produced by the amplifier to the level of extraneous noise that occurs during its operation. This parameter is the main indicator of the overall sound quality — and very clear, because. its measurement takes into account almost all the noise that affects the sound in normal operating conditions. A level of 70 – 80 dB in modern amplifiers can be considered acceptable, 80 – 90 dB is not bad, and for advanced audiophile-class devices, a signal-to-noise ratio of at least 100 dB is considered mandatory.

If the specifications do not specify for which output the signal-to-noise ratio is indicated, it usually means its value for the linear input (see "RCA (par)"). This is quite enough to evaluate the quality of the device for this parameter. However, some manufacturers indicate it for other inputs — Main, Phono; see below for more on this.

signal-to-noise ratio when the amplifier is driven through the Phono input. This interface is for connecting turntables; its features are described in the “Inputs” section below, and for the meaning of any signal-to-noise ratio, see the corresponding section above.

The sensitivity and dynamic impedance of the amplifier when a signal is applied to the RCA line input.

Under the sensitivity of any input (except optical) is meant the lowest signal voltage at this input, at which the amplifier is able to provide normal nominal power values (see "Power per channel (8Ω)"). This parameter determines, first of all, the requirements for the signal source. On the one hand, the voltage provided by this source must not be lower than the input sensitivity of the amplifier, otherwise the latter simply will not give the claimed characteristics. However, a significant excess in voltage should not be allowed, otherwise the sound will begin to be distorted. More detailed recommendations on choosing an amplifier by sensitivity are described in special sources.

For any input other than optical, it is believed that the higher this indicator, the less distortion the amplifier introduces into the signal. The minimum level of input impedance in modern models is considered to be 10 kOhm, and in high-end devices it can reach several hundred kOhm.

The sensitivity and dynamic impedance of the amplifier when a signal is applied to the Phono MM/MC input.

Under the sensitivity of any input (except optical) is meant the lowest signal voltage at this input, at which the amplifier is able to provide normal nominal power values (see "Power per channel (8Ω)"). This parameter determines, first of all, the requirements for the signal source. On the one hand, the voltage provided by this source must not be lower than the input sensitivity of the amplifier, otherwise the latter simply will not give the claimed characteristics. However, a significant excess in voltage should not be allowed, otherwise the sound will begin to be distorted. More detailed recommendations on choosing an amplifier by sensitivity are described in special sources.

For any input other than optical, it is believed that the higher this indicator, the less distortion the amplifier introduces into the signal. The minimum level of input impedance in modern models is considered to be 10 kOhm, and in high-end devices it can reach several hundred kOhm.

The signal level and dynamic resistance (impedance) at the REC output provided in the amplifier.

This output is intended for connection to a recording device. For details, see "REC (to a recording device)"; here we note that the output signal level must be no less than the input sensitivity of the connected device, otherwise the recorded sound will turn out to be too quiet.

The design of modern amplifiers is such that this parameter primarily determines how efficiently the entire circuit works with a low-resistance load: the lower the output impedance, the easier it is to provide the necessary power at such a load. The standard value today is actually 1 kΩ (at 1 kHz); this, usually, is sufficient for most tasks solved by Hi-Fi and Hi-End class amplifiers. The need for other values arises only in special cases; for their description it is worth referring to specialized sources.

The features of the REC output are described in detail in "REC (to a recording device)" below.

Signal level and dynamic impedance provided by the device at the preamplifier output (see "Outputs" for details).

The signal level must not be lower than the sensitivity of the power amplifier (see "Type") to which the signal is received — otherwise the power amplifier will not be able to provide a normal signal level already at its outputs.

Dynamic resistance (impedance) of the preamplifier output. This value is exactly the same as the input impedance of the REC output — see the relevant paragraph above. For more information about the exit itself, see "Exits".

— Euroblock. Analogue audio input (usually line level) using a Euroblock connector. This connector, used mainly in professional audio equipment, is remarkable in that it is attached to the wire using terminals. This is extremely convenient when working with stripped wires (which is often required in professional applications): screwing such a wire to the plug once and connecting / disconnecting the plug to the Euroblock connector is much easier than constantly unscrewing / screwing the terminals. In addition, such a connection is often made balanced (see "XLR (balanced)" below). Inputs of this type are found mainly in information and information-concert amplifiers (see above).

— Phono. Dedicated input for connecting to the amplifier turntables; often has a suffix indicating the type of cartridge that is compatible, such as "Phono MM" or "Phono MM/MC" (see "Advanced — Phono Stage" for details). Despite the proliferation of digital formats, these players are still highly regarded by audiophiles for their high quality and fidelity, and are often used in premium audio systems. However, connecting a "turntable" has its own characteristics — in particular, it requires a phono stage (for more details, see ibid.) — and standard inputs are unsuitable for this purpose. Therefore, a Phono jack is a must if you want to connect your turntable directly, without an external phono stage.

— USB B. The USB interface is widely used in com...puter technology for various peripherals. The presence of a type B input means that the amplifier can be connected to a computer as an external controlled device (slave). Most often, with this connection, it is used as an external sound card or audio interface — this provides higher sound quality and more extensive options for its settings than most built-in sound cards, even expensive ones. However, the matter is not limited to this: in some models, via USB type B, you can update the firmware or change the special parameters of the amplifier.

— Coaxial S / P-DIF. Digital audio input, a variation of the S/P-DIF interface based on a conventional electrical signal (the second variation, optical, is described below). Usually uses a common RCA connector, known as a "tulip", but has rather strict cable requirements. The bandwidth of any version of S / P-DIF is quite sufficient even for high-quality multi-channel sound, and the coaxial version itself is simpler, cheaper and more reliable than the optical one, but more susceptible to interference.

— Optical. Input for transmitting digital sound using light signals, via TOSLINK fiber optic cable; one of the versions of the S/P-DIF standard. The main advantage of optical fiber over traditional electrical cables is complete insensitivity to electrical interference; at the same time, it is more expensive and requires rather careful handling (in particular, it does not tolerate sharp bends).

— Balanced digital ( AES/EBU). The AES/EBU interface is used in the professional field to transmit audio in digital format. It can use several connection types; in this case, it means transmission over the so-called balanced line using an XLR connector. Both the principle of balanced connection and the connector itself are described in detail in the “XLR (balanced)” section below — however, in the case of AES / EBU, we are talking about a digital signal, not an analogue signal.

— COM port ( RS-232). A connector used to control the amplifier from a computer. Through it, you can change the settings, incl. and quite thin, and in some models even update the firmware. Usually, for such purposes, special software is required, which can be supplied with the amplifier.

— Control input (IR). Connector for connecting an external infrared remote control receiver. When properly placed, such a receiver will allow you to use the remote control even in places where the signal from the remote control cannot reach the main (built-in) sensor — for example, in another room. For such purposes, not only sensors can be used as a separate device, but also system components that are compatible with the remote control — for example, players or tuners.

The number of line inputs in the amplifier design using the RCA interface. Unlike the Main input (see above), which can work with the same connectors, when connected to a linear RCA, the signal goes through all the stages of processing provided for in the amplifier — for example, adjusting the balance or frequencies (see "Adjustments"), etc. .P.

See “Amplifier Input (Main)” for details on the connector itself. Here we note that when using RCA as a linear interface, a pair of such connectors is considered one input. This is due to the fact that only one channel can be transmitted over one coaxial cable, so a pair is needed to work with stereo sound.

The number of signal inputs (of any type) determines how many signal sources can be simultaneously connected to the amplifier. Accordingly, it is worth choosing a model according to the number of inputs, taking into account the expected number of such sources: after all, it is easier to connect them all and select them through the amplifier’s remote control or control panel than to fiddle with reconnecting every time.