Comparison AirOn ProCam 4K Plus vs Eken H9R

The degree of dust and water protection of the protective case supplied with the camera.

Protected case will save your camera from dust, water, temperature changes, shocks, etc. The specific degree of protection is indicated according to the international IP (Ingress Protection Rating) system, according to which each device is assigned a code of the form IPXX, where X is replaced by specific numbers. The first of them characterizes the protection against the penetration of foreign objects (from 0 to 6, where 0 is no protection). Usually, in boxes for action cameras, this indicator does not go below 5, because otherwise the container would have too large gaps, and its use simply would not make sense. Level 5 provides dust resistance — dust can get inside the case, but in small quantities that do not affect the device inside. Level 6 corresponds to complete imperviousness to dust.

The second digit is protection against liquid ingress (from 0 to 8, where 0 is no protection). Usually, the minimum level of protection against water is 6.

6 — protection against short-term immersion (for example, falling into a sea wave);
7 — protection against temporary immersion under water (up to 30 minutes) to a shallow depth (up to 1 metre), without continuous operation in immersed mode;
8 — protection against immersion to a depth of more than 1 metre for a time of more than 30 m, with the possibility of continuous...operation underwater. The specific level of protection of level 8 can be quite impressive — up to the possibility of diving to several tens of metres.

Note that protective cases for action cameras can be sold separately. Therefore, if the capabilities of the complete container do not suit you, there may be a more secure case on the market. On the other hand, in general, it is still more convenient to buy such an accessory immediately with a camera — so as not to waste time and effort on choosing the right protective case.

The ability of the camera to record HD video (720p).

The official HD specification provides a resolution of 1280x720. However, in action cameras, there may be resolutions slightly different from this parameter, for example, 1080x720 or 1440x960. Anyway, HD is the most modest of today's high-definition standards, which, nevertheless, provides a fairly clear and detailed image.

Another important parameter given in this paragraph is the frame rate. The higher it is, the smoother the movement in the frame will be, and the details in dynamic scenes will be visible clearly. Technically, 30 fps or even less is enough for video, but 60 fps is considered the perfect value — at this frame rate, motion blur becomes almost imperceptible and at the same time the size of the captured files remains within reasonable limits. However, there are cameras on the market with higher frame rates at HD resolutions — 100 fps, 120 fps, 200 fps and even 240 fps. This speed is usually used for recording slow-motion video, but such a possibility needs to be specified separately.

Frame rate supported by the camera when shooting in slow motion.

In general, such shooting is called “high-speed” because it is carried out at an increased frame rate (more than 60 fps). As a result, when played back at normal speed (60 fps and below), the video looks slow hence the name. This kind of slow-motion can be used just for fun, as an artistic technique, and even for scientific purposes — to capture movement that is too fast for the human eye. In any case, the higher the slow-mo frame rate, the more you can slow down the video and the more advanced the camera is in this regard. On the other hand, the higher the frame rate, the more performant the graphics part should be; and this, in turn, affects the price of the device, sometimes quite noticeably.

We also note that slow-mo shooting may be available only at certain resolutions, not always at maximum. These points can be directly specified in the specs of the action camera.

The maximum resolution at which the action camera can take photos. Specified in pixels horizontally and vertically.

This parameter is directly related to the resolution of the image sensor(see above): the total number of pixels in the photo, usually, corresponds to the number of pixels in the sensor. For example, a photo resolution of 4608x3456 corresponds to a sensor of 15925248 pixels, or approximately 16 megapixels. If the number of pixels in the photo is greater than the claimed resolution of the sensor, then the manufacturer uses software tricks that allow you to improve the photo resolution to a higher one than originally. This reduces the cost of devices but also affects the quality of images.

Theoretically, high-resolution images can provide good detail, but in fact, much depends on the specs of the sensor (primarily physical size) and image processing features.

— Diagonal. The larger the screen, the more convenient it is to watch (and also to control if the display is touch-sensitive). On the other hand, the diagonal of the built-in display directly affects the size of the case, and action cameras should be quite compact. Thus, there are practically no screens larger than 2.5" in modern action cameras.

— Resolution. Theoretically, the higher the resolution, the clearer and better image the screen produces. On the other hand, displays in action cameras are designed mainly for menu operation and footage preview — and for these purposes, especially high resolutions are not needed. For models with two screens, the rear display is considered the main display.

— Touch screen. Display equipped with a sensor and responsive to touch like in smartphones/tablets. Control through such a display is simpler and more intuitive than using buttons, rotary knobs, etc. On the other hand, for more or less convenient control, the touch screen must be quite large, which affects the dimensions of the entire camera.

The presence in the camera of a screen mounted on the front panel, next to the lens. Other displays may not be present at all; in such cases, the diagonal, resolution and other parameters are given for the front screen.

It is worth noting that most often the simplest black-and-white displays are installed on the front panel, suitable only for text and basic graphic information. However, even on such a screen, you can display a wide variety of service data: the current mode of operation (photo, video, standby), the resolution used, the shooting time, the amount of free space on the drive, etc. But more advanced displays are not used as front displays: a full-colour screen is needed only for taking a selfie, and for this you can use a remote display with a remote control(see "Control") or a smartphone connected to the camera.

Speaker or speakers installed directly in the camera body. This function is mainly intended to allow you to view footage with sound without connecting headphones or external speakers. However the built-in speakers do not have decent volume or general sound quality — nevertheless, they allow you to determine what the camera “heard” as a whole, whether sound recording was turned on, whether individual ambient sounds got into the recording, etc.

The largest memory card capacity supported by the camera model.

This limitation is due to two points. First, the larger the drive, the more computing power is required to use it. Secondly, each type of memory card has its maximum capacity. For example, the capacity of an SD HC card cannot exceed 32 GB, larger drives already belong to the SD XC standard, and if it is not supported, the maximum card capacity cannot exceed 32 GB.

It is strongly not recommended to exceed the maximum allowable capacity: even if the card is recognized by the device, its normal operation is not guaranteed.

— Protective case. A special container that provides additional protection from dust, moisture, impacts, extreme temperatures and other similar "troubles". The specific level of protection in each case should be specified separately. In order not to interfere with filming, the box is made of transparent materials. In addition, we note that some cameras can only be mounted on mounts in a box (or in a mounting frame - see below), since the body itself may not have space for this.

— Mounting frame. A device designed to install a camera on various mounts — helmet, steering wheel, etc. The camera body itself often does not have "landing sites" for such mounts, which is why additional equipment has to be used. Note that a protective box (see above) often performs a similar function; the mounting frame, in contrast, provides almost no protection, but the camera body remains maximally open in the frame. This provides additional opportunities — in particular, it allows you to connect various cables and effectively use the built-in microphone, which is impossible when using many boxes.

— Helmet mount. A mount designed to mount a camera to a helmet or other curved surface. The design of such a mount is based on a curved platform with an adhesive layer or Velcro, the shape of which roughly matches the shape of the helmet surface. Such a device can provide a more s...ecure hold than a classic flat platform (see below).

— Flat mount. One of the main and simplest mounts used to fix an action camera to almost any uniform surface: snowboard, skateboard, car hood, etc. It is a small flat platform, to one side of which the camera is attached, while the second is fixed to the desired surface (using Velcro, special glue, etc.). Note that flat mounts are often used for installation on a helmet, but for this purpose there is a separate type of mount, with a curved platform (see above).

— 3-axis mount. This differs from other types of mounts by the presence of three movable units that allow you to rotate the camera at an angle of up to 90 degrees in three axes. In practice, this allows you to choose the most interesting or successful shooting angle - on the side of the helmet, for example. Such solutions are usually compatible with many other mounts, so they can be used together with a steering wheel, curved, etc.

— On the handlebars of a bicycle/motorcycle (pipe). A mount for installing a camera on a small pipe — for example, the handlebars of a bicycle or motorcycle. As a rule, it works on the principle of a clamp, and the size of the mount can be adjusted within a fairly wide range, adjusting it for pipes of different diameters.

— Suction cup(on glass). A camera mount that is fixed in the desired location using a suction cup. Allows you to install the device on flat and slightly curved surfaces. It is worth considering that such mounts do not hold as securely as flat or curved ones (see the relevant points). On the other hand, the suction cup is easy to attach and remove and leaves no marks. Therefore, mounts of this type are mainly used for installation on car glass when the camera operates as a video recorder.

— Clamp (clip). The clip-type mount is quite universal, since it allows you to hang the camera on almost any suitable piece of equipment (backpack strap, unloading belt, belt, etc.). However, it is not very suitable for extreme shooting due to its relatively low reliability.

— Head mount. A device for fixing the camera to the head — usually on the forehead, like a headlamp. In addition to freeing up your hands, this placement has another advantage: the camera lens looks in the same direction as the customer. The mount itself is usually a system of elastic straps and is designed to be worn directly on the head, as opposed to a curved helmet platform. However, some models allow the possibility of wearing it over a helmet.

— Chest mount. This mount is a system of elastic straps that allows you to fix the camera on the customer's chest, shooting slightly lower than "from the eyes". Like the head mount (see above), it is easily adapted to the desired size.

— Monopod(selfie). A device commonly known as a “selfie stick”. It is a rod, usually foldable and sometimes adjustable in length; at one end of the rod there is a mount for the camera, at the other - a handle for holding in the hand. In accordance with the name, such a monopod is intended mainly for filming yourself - thanks to the length of the rod, the camera can be held at a comfortable distance. However, other ways of using it are possible: for example, with the help of a monopod you can “look” quite far over the edge of a cliff or around a corner. The main disadvantage of such a device is that one hand is constantly occupied.

In addition to those described above, the delivery set may also include other types of fastenings - for example, for musical instruments (on the neck of a guitar, on the bar of a drum kit, etc.), on a surfboard, etc.