Comparison Thermos 34 Premier 1L 1 L vs Thermos FBB-1000 1 L

The type of main cover provided in a thermos. The main cover in this case is a device that directly covers the working volume of the vessel; an additional cap can be installed on top of it, which often also plays the role of a cup. In modern thermoses there are the following types of main lids: screw-on (screw), valve, cover, hinged cover, drinking cover, pump (pump), stopper. Here are the features of each of them.

- Screws on (screw). Solid (without holes) screw-on cover, secured with a thread. Such lids are very simple and at the same time reliable, but you cannot drink or drain the contents through the classic screw - you have to remove it completely. There is also a more advanced design that allows you to drain the contents without removing the screw - just partially unscrew it; however, this is a rather specific option that is not used often. Be that as it may, twists are found mainly among classic and food thermoses (see “Type”), for which the mentioned nuances are not decisive.

- Valve. A cover (most often threaded) equipped with a valve through which the liquid contents of the thermos can freely flow. Such lids are more complex and more expensive than “blind” screws (see above), but to access the contents you d...on’t need to unscrew the screw every time, just open the valve. This not only provides additional convenience, but also reduces heat loss. Thanks to these advantages, valves are extremely popular in classic thermos flasks; they are also often used in thermal mugs (see “Type”). The disadvantages of this option include the fact that the valve opening is usually made quite narrow and is easily clogged with impurities (for example, tea leaves or coffee grounds). Therefore, the valve can only be used for liquids without such impurities (this also applies to food thermoses, which can also be equipped with valves). However, there are models with two different valves included, for drinks of different consistencies and aromas.

- Lid. Lids in this case are devices that do not have threads (unlike the screws described above) and are held in place solely by friction or a latch. The design of the lids can be different: some cover the neck from the outside, others are pressed inward when closing; There are also more specific options. In any case, the lids are easy to remove and put back on, but they are not very reliable - for example, it is not recommended to turn such vessels over. Therefore, this option is found mainly in thermal mugs and thermoses for food (see “Type”), for which the mentioned disadvantages are not critical.

— Hinged cover. A variation of the lids described above, which, when opened, is not removed entirely, but is folded to the side on a special mount. Thanks to this, the likelihood of loss is reduced: in fact, you can only lose the cover along with the thermos itself; and a latch, spring, or other similar device is usually provided to hold the cover in the open position. On the other hand, mount somewhat affects the price and dimensions of the vessel. This drawback is least critical for flasks and mugs (see “Type”), and it is among these types that hinged lids are most often found.

— Cover-drinker. Lid (regular or threaded), complemented by a special hole for drinking. This design allows you to drink from the vessel without removing the cover; and during “non-working” hours the hole is covered with a flap or other similar device. Drinking lids are extremely popular in thermal mugs and auto mugs (see “Type”): they allow you to drink from the mug comfortably while at the same time minimizing heat loss and the likelihood of spilling the contents.

— Pump (pump). Lid (classic or threaded) with built-in pump. Most often, this pump is activated by a special button: when you press this button, a portion of liquid comes out of the spout, and the thermos does not need to be tilted. However, such devices are quite complex and cumbersome, so it makes sense to use them only in thermos jugs (see “Type”): the size and weight of the pump is small compared to the dimensions of the jug itself, and tilting such a thermos can be difficult - it’s easier to use a pump.

- Cork. A classic stopper that fits tightly into the neck of a thermos and is held in it without threads or other similar devices. Corks differ from the lids described above in their greater thickness, and also in that they are inserted into the neck from the inside (while the cover can cover the vessel from the outside). Plugs are very easy to use, but have low reliability, which decreases even more as they wear out. As a result, this option has practically fallen out of use.

The material from which the flask is made is the inner container of the thermos, which usually comes into direct contact with the product inside. Among the most popular modern materials are stainless steel, glass, plastic and ceramics; here are their main features:

—
— Glass. The main advantage of glass over stainless steel is complete chemical inertness: such flasks do not oxidize and do not acquire an unpleasant odour over time. This makes them perfect for products where flavor matters a lot, such as herbal blends. In addition, this material retains heat better. On the other hand, the strength of glass is significantly lower, and such thermoses are...rather poorly suited for hiking — mostly glass flasks are placed in models that are not designed for difficult conditions.

— Plastic. This material is characterized by low cost and relatively low thermal conductivity (which helps to retain heat). On the other hand, the plastic surface does not tolerate prolonged contact with hot liquids: it can release unpleasant odours or even harmful substances. Thus, plastic flasks are relatively rare — mainly in thermos mugs, which, by definition, are not designed for long-term storage of hot drinks, as well as in inexpensive food thermoses.

— Ceramics. A material that is in many ways similar to glass: ceramics do not react with the contents of a thermos, do not affect its taste and smell, but are afraid of strong blows. At the same time, the reliability of this material is somewhat higher than that of glass — on the other hand, ceramics are more expensive. Therefore, this option has not received much distribution.

The material from which the body is made is the outer part of the thermos, inside of which the flask is placed.

— Plastic. One of the main advantages of this material is its low cost. In addition, it can be given any colour, and low thermal conductivity contributes to better temperature retention. On the other hand, plastic cases are noticeably inferior to steel cases in terms of strength and reliability, and scratches easily appear on their surface, due to which the product loses its presentation as it wears out. Therefore, plastic is used mainly in inexpensive models of thermoses.

— Stainless steel. Steel is somewhat more expensive than plastic, but much stronger and more reliable. In addition, the steel surface has a stylish appearance that is long-lasting thanks to its scratch resistance. Among the shortcomings of this material, in addition to the price, high thermal conductivity can be noted; manufacturers usually compensate for this moment with various tricks that further increase the price. Nevertheless, in general, steel is a very favorable material in terms of price and quality, and it is from it that the cases in most modern thermoses are made.

This feature means that the thermos is equipped with two cups or bowls at once (depending on the type, see above).

Many modern thermoses are equipped with a drinking cup or a food bowl; in the stowed position, such a container usually plays the role of a lid. In some models of cups / bowls, there can be two at once, which is useful if the thermos is used not only for yourself: you do not have to carry additional dishes with you separately.

The special handle for convenience of carrying of a thermos. The design of such a handle can be different: for example, in ordinary thermoses and thermo mugs (see "Type") it is usually installed on the side, in food thermoses and jugs — from above (and is made collapsible). The handle can be a structural element of both the thermos itself and its cover (see below). In addition, the small carrying strap that some models are equipped with is also considered a handle in this case (but the shoulder strap does not count, see below).

Anyway, holding a thermos by the handle is usually more convenient and safer than by the smooth body, especially when it comes to a large-capacity model.