Comparison Ferocon E137K.T1.P2-9005 vs Paritet-K GRIFFON M.25.K

The product type determines the main purpose and some design features of the safe.

— Home/office. Freestanding general purpose safes; the office variety is somewhat larger than the home variant, but otherwise their features are identical, so both types are combined into one. These are rather simple products with relatively low burglary resistance and without fireproof, not intended for storing weapons and not designed for carrying (for more details, see the relevant subparagraphs below). They are designed primarily to protect information of a low rate of privacy — for example, commercial documents "for official use".

— Embedded. This category includes all models of safes designed for installation into a wall — in such a way that only the front door is outside. If the safe meets this criterion, it is classified as embedded, regardless of the burglary protection rate and/or fire resistance. The advantage of such safes is the minimum space occupied; in addition, a wall safe is easy to disguise, for example, under a picture. On the other hand, the embedding process itself is quite troublesome, and moving the safe to another place can be a serious problem. And the burglary resistance of such models is usually not very high — in fact, it is directly related to the specs of the wall material the safe is installed into.

— Burglary. General-purpose...safes that do not have any of the specializations described below and at the same time correspond to a burglary resistance class (see the relevant paragraph) of at least I.

— Fireproof. General purpose safes that are not applicable to the types described below and have a fire rating (see “Fire Rating”) of 30B or higher. It should be noted that the main purpose of such safes is not to provide security, but to protect the contents in case of fire: even the simplest fire-resistant safe will be able to protect the documents placed in it to a certain extent, but the reliability of the locks and the burglary resistance of such models is very limited.

— Fire and burglary resistant. Models that combine the properties of the two "resistant" types described above: general purpose, burglary resistance of at least level I and fireproof rating of at least 30B.

— Gun safe. A specialized type of safe designed to store firearms and ammunition. Such models may have devices for the convenience of placing guns, as well as additional compartments for ammunition (see "Ammo compartment"). Another characteristic feature of gun safes is the possibility of fastening (see below) — this requirement is often found in the legislation of different countries. Note that the presence of such a gun safe may be one of the conditions for issuing a weapon permit, and the specific requirements for a gun safe in such cases are also specified in the law. Therefore, before buying such a model, it is worth checking its compliance with local requirements.

— Deposit. A specific type of safe used in retail outlets, exchange offices and other places where you constantly have to deal with a large amount of cash. The main feature of such safes is the presence of an additional (cash) compartment above the main one. Such a compartment opens freely, without a key or other similar restriction, and when it is closed, all contents placed inside (money, securities, etc.) automatically move to the lower, protected compartment. Thus, it is possible to replenish the contents of the main compartment without access to it. The burglary resistance of such safes is relatively low, since they are always under supervision. It is also worth noting that the presence of a slot for money (on top or on the door) also makes the safe deposit one.

— Portable/car. Two types of safes combined into one according to the criteria of small size and portability. Moreover, each option has its own specs. So, portable ones are often equipped with a handle for easy transportation in the hands, and automobile ones are designed with the expectation of specific installation locations: under the front seat for the role of the second “glove box”, under the folding segment of the rear seat, in the spare wheel in the boot, etc. Both subtypes have the ability to mount (see below) — otherwise there is a high risk of stealing the contents directly with the safe for later opening.

— Filing cabinets. A kind of safe designed, in accordance with the name, for storing various documents, and documents with a low rate of privacy. The last is due to the fact that filing cabinets have very limited security specs: low thickness wall, fairly simple key locks, a minimum burglary resistance class (H0, see below) or no such at all. In fact, the task of such safes is not to resist professional hacking, but to restrict access for ordinary people (for example, employees of the same institution) who do not have a key.

— Safe with thermostat. A safe equipped with a thermostat — a device for maintaining a certain temperature inside. Such models are mainly used for the storage of narcotic, psychotropic, precursors and other drugs and substances that require not only access restrictions, but also special storage conditions. Many thermostatic safes are initially marketed as "medical" safes, and may have special settings to comply with regulatory requirements for the storage of drugs — for example, the "storage in a cool place" mode.

The volume of the interior space of the safe. Usually this parameter is indicated taking into account the safe-in-safe and other additional internal compartments. The amount of content that can be placed inside directly depends on the volume; on the other hand, it affects the external dimensions and weight of the storage.

A parameter that characterizes the degree of resistance of the safe to burglary - that is, direct damage to the door or wall in order to gain access to the contents.

Safes manufactured in different countries have different certifications for burglary resistance. So, in accordance with the Ukrainian standard DSTU EN 1143-1:2019, there are 13 classes of burglary resistance of safes. The same number of gradations are available in the ECB-S marking, which is assigned to safes by the European Security Systems Association (ESSA). The classification covers not only resistance to damage, but also the tear resistance of an anchored safe, and bracing is required to classify safes weighing less than a one ton (see below). Pull-off resistance is simply determined by the force required to remove it from the mount; this force is indicated in newtons, 10 N corresponds approximately to a force of 1 kg. To assess the resistance to damage there are so-called resistance units (Ru) - breaking time multiplied by the coefficient of resistance of the tool used. For each type of tool, the coefficients are different - for example, from 1 to 5 for a chisel, 5 for an electric drill, etc. For example, if a control sample of a safe of a certain model was cracked by a drill in 4 minutes, then its resistance to cracking is 20 Ru. Note that the check is carried out in two versions - for full and partial access to the contents of the safe; when assigning a class, both results are taken into accou...nt, they are often written as "partial/full resistance", for example 120/180.

Now there are safes on the market with the following burglary resistance classes: H0 class, Class 0, Class I, Class II< /a>, Class III. Safes with a higher burglar resistance class (Class IV, V class, Class VI, Class VII, Class VIII) are much less common.

Detailed data for each class can be found directly in the regulatory documentation. For example, here are the first three classes:

— H0 class (“below zero”). Minimum burglary resistance class to be certified. Requires a resistance of at least 15 Ru for both access options, and a pull force of at least 50 kN.
- 0 class. Safes with a resistance of at least 30/30 Ru and a pull force of 50 kN or more.
- I class. Models with a resistance of at least 50/30 Ru and a breakout force of 50 kN. The minimum class for safes classified in our catalog as burglar-resistant (see "Product Type").
There are also more burglary-resistant models on the market - up to class VIII.

The burglary resistance class is confirmed by a certificate issued by state bodies for technical regulation and standardization. The validity period of the certificate is limited, and usually it is much less than the time during which this or that model is produced. Therefore, safes are regularly re-certified. For a number of reasons, new results may differ from previous results and correspond to a different resistance class than that recorded in the outdated certificate. Therefore, over time, the class of the same model may change even if the quality of the safes themselves remains unchanged.

The number of locking bolts provided in the design of a standard safe lock.

The locking bolt is a working element of the lock, which responds directly to the locking. It is a rod, disk, or other element (usually metal) that fits into a slot in the fixed part of the safe, blocking the opening of the door. The more such elements a safe has, the more reliable the lock and the lower the probability of opening the door by “brute force”.

This parameter in our catalog is indicated for one lock, regardless of their number in a safe. Most often, all safe locks have the same number of bolts.

Now on the market there are locks with the following number of locking bolts: 2, 3, 4, 5, 6 and more.

This paragraph indicates the manufacturer of the safe lock.

The number of individual shelves provided in the design of the safe (if any). These structural elements make it easier to store small items: it is easier to lay out the "trifle" on separate shelves than to lay it in a continuous pile on the floor of the safe. On the other hand, shelves divide the overall volume of the safe into parts and can create difficulties for large items. Therefore, in gun safes (see "Product Type"), the shelves occupy only a part of the internal space, which is separated from the rest of the volume by a vertical partition.

Some safes provide the possibility of rearranging the shelves to different levels — similar to how it is implemented in refrigerators.

The minimum design of the safe provides 1 or 2 shelves, and in more advanced models their number can reach 3 or more.

The number of firearms the specialized safe is designed to store (see "Product type").

In this case, it means the maximum number of individual slots for weapons in the safe. At the same time, such slots can be designed for different classes of weapons: most weapon models are made for shotguns, carbines and other long-barreled weapons, but pistol safes are also produced. And it is worth considering that with the full equipment of the safe (shelves, internal compartments), it will not always be possible to fit all the weapons. This will require the dismantling of the shelves.

Also note that the market offers both "personal" gun safes for a small number of guns, and products designed for military units, police departments, security firms, etc. and capable of accommodating several dozen of weapons units.

Now there are safes on the market for such a number of weapons: up to 3 pcs, from 4 to 6 pcs, from 7 to 10 pcs and more.

The presence in the design of the gun safe (see "Product Type") of a separate compartment for storing ammo. Such a compartment is located inside the main compartment and is locked with its own lock — in this sense it is similar to a cash box (see below). In some CIS countries, the presence of an ammo compartment is prescribed by law as a mandatory requirement for a gun safe — this feature increases the security of storage and reduces the likelihood of illegal gaining access to weapons with ammo.

The size of safe regarding its external dimensions. These figures will allow you to estimate how much space the safe takes up and whether it will fit into the intended installation location. Of course, greater capacity implies larger dimensions.