USA
Catalog   /   Climate, Heating, Water Heating   /   Heating & Boilers   /   Solar Collectors

Comparison Atmosfera SPK F4M vs Atmosfera SPK F2M

Add to comparison
Atmosfera SPK F4M
Atmosfera SPK F2M
Atmosfera SPK F4MAtmosfera SPK F2M
Outdated ProductOutdated Product
TOP sellers
Typeflatflat
Loop systemclosedclosed
Mountinginclinedinclined
Suitable forheating and DHWheating and DHW
Year-round use
Design
Absorber materialcoppercopper
Absorber area1.87 m²1.88 m²
Total collector area2 m²2 m²
Technical specs
Efficiency84.9 %78.9 %
Absorber absorption coef. α95 %95 %
Absorber emissivity coef. ε5 %5 %
Stagnation temperature208 °C208 °C
Heat loss coef. k13.778 W/m²*K3.327 W/m²*K
Heat loss coef. k20.016 W/m²*K0.020 W/m²*K
More specs
In box
1 collector
1 collector
Dimensions (WxHxD)1006x1988x85 mm1006x1988x85 mm
Collector weight40 kg40 kg
Added to E-Catalogjanuary 2018january 2018

Absorber area

The total area of the absorbing surface of the collector. For kits with multiple collectors (see "Number of collectors"), the area for one device is indicated.

Note that the meaning of this parameter depends on the type of collector (see the relevant paragraph). In flat devices, we are talking about the working area — the size of the surface that is exposed to sunlight. In tubular models (vacuum, thermosiphon), where tubes play the role of an absorber, the total surface area of the tubes is taken into account — including that which is “in the shade” during operation and is not heated by the sun. Special reflectors can be used to overcome this problem.

All of the above means that only collectors of the same type and similar design can be compared with each other in terms of absorber area. If we talk about such a comparison, then a large area, on the one hand, provides greater efficiency and heating speed, and, on the other hand, it accordingly affects the dimensions of the device and the amount of space required for its installation. Thus, the total area of a flat collector approximately corresponds to the area of the working surface; it is slightly larger, but this difference is small. But in tubular models, there is a paradox when the total area is less than the absorber area.

Efficiency

Collector efficiency.

Initially, the term "efficiency" refers to a characteristic that describes the overall efficiency of the device — in other words, this coefficient indicates how much of the energy supplied to the device (in this case, solar) goes to useful work (in this case, heating the medium). However, in the case of solar collectors, the actual efficiency depends not only on the properties of the device itself but also on environmental conditions and some features of operation. Therefore, the specs usually indicate the maximum value of this parameter — the so-called optical efficiency, or "efficiency at zero heat loss." It is denoted by the symbol η₀ and depends solely on the properties of the device itself — namely, the absorption coefficient α, the glass transparency coefficient t and the efficiency of heat transfer from the absorber to the coolant Fr. In turn, the real efficiency (η) is calculated for each specific situation using a special formula that takes into account the temperature difference inside and outside the collector, the density of solar radiation entering the device, as well as special heat loss coefficients k1 and k2. Anyway, this indicator will be lower than the maximum — at least because the temperatures inside and outside the device will inevitably be different (and the higher this difference, the higher the heat loss).

Nevertheless, it is most convenient to evaluate the specs of a solar collector and compare it with oth...er models precisely by the maximum efficiency: under the same practical conditions (and with the same values of the coefficients k1 and k2), a device with a higher efficiency will be more efficient than a device with a lower one. .

In general, higher efficiency values allow to achieve the corresponding efficiency, while the collector area can be relatively small (which, accordingly, also has a positive effect on dimensions and price). This parameter is especially important if the device is planned to be used in the cold season, in an area with a relatively small amount of sunlight, or if there is not much space for the collector and it is impossible to use a large-area device. On the other hand, to increase efficiency, specific design solutions are required — and they just complicate and increase the cost of the design. Therefore, when choosing according to this indicator, it is worth considering the features of the use of the collector. For example, if the device is bought for a summer residence in the southern region, where it is planned to visit only in summer, relatively little water is required and there are no problems with sunny weather — you can not pay much attention to efficiency.

Heat loss coef. k1

The heat loss coefficient k1 to which the collector corresponds.

This indicator is purely reference: along with the coefficient k2, it is used to calculate the actual efficiency of the device in a particular situation (for more details, see "Efficiency"). However, a lower k1 gives less heat loss and higher real efficiency.

Heat loss coef. k2

The heat loss coefficient k2 to which the collector corresponds.

This indicator is purely reference: along with the coefficient k1, it is used to calculate the actual efficiency of the device in a particular situation (for more details, see "Efficiency"). However, a lower k2 gives less heat loss and higher real efficiency.
Atmosfera SPK F4M often compared
Atmosfera SPK F2M often compared