Comparison Beko FSE 62330 GWD white vs Beko FSM 62330 DWT white

It is the volume of the oven provided in the stove. It s the maximum volume of products that can be placed in it without compromising work efficiency. Accordingly, a larger oven is useful for large volumes of cooking; on the other hand, such a capacity will significantly affect the price and dimensions of the stove.

If you buy a regular household stove with 4 burners and do not plan to cook a lot in the oven, you can not pay much attention to this parameter. The capacity of the oven is usually enough for most simple tasks like cooking a pie or baking chicken. But for more serious tasks, a larger oven may be required. Detailed recommendations on volumes can be found in special sources.

If there is an additional chamber (see below), this paragraph usually indicates only the volume of the main oven.

It is the number of cooking modes provided in the design of the oven. This item shows the typical cooking modes — for example, “heating”, “heating + convection”, etc. Accordingly, this parameter is highly dependent on additional equipment. However, even in similar models, the number of modes may be different. In general, the more there are, the more opportunities for cooking, and the easier it will be to choose the optimal mode for a specific situation.

It is the method of cleaning the inner surface provided in the design of the oven. In addition to traditional and more advanced steam cleaning, there are catalytic and pyrolytic cleaning. More about them:

— Traditional. This option assumes the absence of any devices that facilitate cleaning: you have to wash the oven manually, using ordinary detergents and cleaning products. Such a procedure can be quite troublesome and time-consuming, but such ovens are much cheaper than similar models with more advanced types of cleaning.

— Pyrolytic. Cleaning with high temperature. Dirt on the interior surfaces of the oven is burned to ash, which can then be easily removed without using detergents. At the same time, pyrolytic cleaning equally effectively handles all types of dirt, both new and old. The disadvantages of such a system are the duration of cleaning (sometimes up to several hours), high cost, and significant consumption of resources (electricity or gas, depending on the type of oven). In addition, during the operation of the cleaning system, unpleasant odours often arise, generated by the combustion of contaminants in the oven.

— Catalytic. Ovens with this type of cleaning have a special coating on the inner surface that breaks down grease on the oven walls. Fat disintegration is accelerated at high temperatures; the oven is thus self-cleaning t...o a certain extent. However, the efficiency of catalytic cleaning is lower than that of pyrolytic cleaning. It is unable to cope with the entire amount of fat on the walls. Therefore, such an oven should be washed from time to time. On the other hand, ovens with catalytic cleaning are cheaper than ones with pyrolytic cleaning. And the cleaning itself does not require additional electricity/gas costs, nor is time-consuming (except for washing/wiping).

— Steam cleaning. Cleaning the oven with heated steam. A certain volume of water is poured into a baking sheet or another container, the container is placed in the oven and the cleaning mode is turned on. Due to heating, the water evaporates, and the heated steam softens the dirt on the walls and partially disintegrates the fat. After the end of the programme, it is enough to wipe the oven with a damp cloth. Such a cleaning requires less time and resources than pyrolysis and often turns out to be more effective than catalytic — steam can soften even old dried-up contaminants. At the same time, these ovens are relatively inexpensive. At the same time, this mode does not guarantee to cope with any contamination. It is possible that after the end of the steam cleaning, the oven will have to be washed traditionally.

Type of tray guides provided in the oven.

— Frame. The simplest guides are made in the form of a fixed grid, and sometimes in the form of slots in the walls of the oven. They are quite practical and inexpensive, due to which they are used in the vast majority of ovens. The main disadvantage of the lattice guides can be called the fact that the baking sheet moves rather tightly in them, especially if the oven has not been cleaned for some time and the guides are dirty.

— Telescopic. Guides in the form of retractable tray support based on telescopic rails. When removing the baking sheet, the mechanism moves apart, and the stand, rolling on a special roller, “leaves” the oven. The main advantage of the "telescopic rails over the classic frame guides is that you do not need to make much effort to install and remove the baking sheet — it will move very easily. On the other hand, such devices are more expensive and more complicated than classic frame guides; as they get dirty, their efficiency drops noticeably, and dirt can completely disable the mechanism. In light of all this, manufacturers most often use telescopic rails not as the main option but as an addition to the frame guides described above. If telescopic guides are initially indicated in the specs of the stove, this usually means that the oven with traditional frame guides is additionally equipped with removable telescopic guides. These advanced telescopic rails ca...n be easily set at the desired level and removed for cleaning.

Many ovens, initially equipped only with frame guides, can be equipped with telescopic rails, purchased separately.

The type of gas control provided in a stove with a gas hob and/or oven.

Gas control is a safety system for gas stoves that turns off the gas supply when the flame goes out. Such a system can be used only in the stove, only in the oven, or both. The latter option, from a safety point of view, is considered perfect for gas stoves. However, gas control is more important for an oven — it is more difficult to control the presence of a flame in it. But in the hob, this function is not so critical, especially if the stove is constantly under supervision during cooking.

A security measure that allows you to block the controls of the stove. It will be useful in families with small children: when the lock is on, a curious child will not be able to turn on the stove or change settings. To unlock, one needs to perform certain actions, which are easy for an adult and too complex for a child: for example, you need to press two specific buttons simultaneously.

A display on the stove control panel. Usually, it is a very simple one-colour display : 3-4 digits plus a few additional characters (for example, a thermometer icon and a clock icon). However, even on such a display, almost all important information related to the stove operation can be displayed: heating temperature, clock, timer settings, and other relevant data. Thus, the display significantly simplifies the management of the stove and makes it more convenient.

For technical reasons, this function is mainly used in electric stoves; there are also gas models with displays, but they are extremely few.

The energy class describes the overall efficiency of the cooker in terms of energy consumption. Note that we are not talking about actual consumption (see "Connected load" for details), but about the efficiency of the stove, about the efficiency of using the energy that it consumes.

This indicator is especially important for models with at least one electric burner or electric oven/grill. But, if we are talking about a purely gas stove, you can not pay much attention to the energy consumption class. Electricity in such models is spent only on additional functions like auto-ignition or oven lighting,

Initially, the classes were marked in Latin letters from A(the most economical) and then alphabetically in order of decreasing efficiency — B, C, D ... Later, improved classes A+, A++ appeared; the more pluses, the higher the efficiency. Today, energy consumption in class A can be called medium, and in a lower class — high. The maximum indicator found in modern stoves is A++; if we are talking about a model with an electric burner, such a stove is usually expensive, but it pays off by saving electricity during use.

The connected load of the stove is the maximum electrical power consumed during operation. This parameter is indicated only for models that are equipped with at least one electric heater — burner (burners), oven or grill. It is the burners that are the highest consumption in terms of energy consumption; Features such as auto-ignition or oven lighting require little energy, a ordinary socket is enough for them.

First of all, the requirements for the power grid depend on this indicator: it must be able to provide such power without overload. It is worth noting that for household sockets the power limit is about 3 – 3.5 kW; with more power, you need to connect the stove to a 230 V network according to special rules. An alternative is a three-phase 400 V mains: most modern stoves with electric heaters allow connection to both 230 V and 400 V.