USA
Catalog   /   Sound & Hi-Fi   /   Hi-Fi & Hi-End Components   /   Amplifiers

Comparison Pioneer A-30 vs Pioneer A-10

Add to comparison
Pioneer A-30
Pioneer A-10
Pioneer A-30Pioneer A-10
from $480.00 up to $604.80
Outdated Product
from $213.32 up to $399.60
Outdated Product
TOP sellers
Device typeintegrated amplifierintegrated amplifier
Element basetransistortransistor
Amplifier parameters
Number of channels22
Frequency range
5 – 100000 Hz /+0 -3 дБ/
5 – 100000 Hz /+0 -3 дБ/
Power per channel (8Ω)40 W30 W
Power per channel (4Ω)70 W50 W
Signal to noise ratio105 dB105 dB
Signal to noise ratio (Phono MM/MC)77 dB77 dB
Harmonic distortion0.01 %
Channel sensitivity / impedance
Line input
200 mV
50 kOhm
200 mV
50 kOhm
Main input
1 V
10 kOhm
 
 
Phono MM/MC
2.8 mV
50 kOhm
2.8 mV
50 kOhm
REC output
200 mV
2.2 kOhm
200 mV
2.2 kOhm
Connectors
Inputs
Phono
control input (IR)
Phono
 
To amplifier (Main)RCA
RCA5 pairs5 pairs
Outputs
control output (IR)
 
For acoustics4 шт4 шт
REC (to recorder)1 pairs1 pairs
On headphones6.35 mm (Jack)6.35 mm (Jack)
Front panel
indicators
headphone output
indicators
headphone output
Features
Adjustments
bass control
treble adjustment
balance adjustment
level adjustment
loudness
bass control
treble adjustment
balance adjustment
level adjustment
loudness
More features
By-pass/Direct
auto power off
ММ phono stage
additional speaker connect
Bi-Wiring
external devices control
By-pass/Direct
auto power off
ММ phono stage
additional speaker connect
Bi-Wiring
 
General
Remote control
PSUinternalinternal
Power consumption175 W135 W
Standby consumption0.3 W0.3 W
Dimensions (WxDxH)435x360x128 mm435x360x128 mm
Weight7.9 kg6.7 kg
Color
Added to E-Catalogjanuary 2014january 2014

Power per channel (8Ω)

The nominal sound power output by the amplifier per channel when operating with a load having a dynamic resistance (impedance) of 8 ohms. In our catalog, this parameter is indicated for the mode when all channels of the amplifier work under load (see "Number of channels"); in the presence of unused channels, the rated power may be slightly higher, but this mode cannot be called standard.

Rated power can be simply described as the highest output signal power at which the amplifier is able to work stably for a long time (at least an hour) without negative consequences. These are average figures, because in fact, the audio signal is by definition unstable, and individual level jumps can significantly exceed the rated power. However, it is she who is the main basis for assessing the overall loudness of the sound.

This indicator also determines which speakers can be connected to the amplifier: their rated power should not be lower than that of the amplifier.

According to the laws of electrodynamics, with different dynamic load resistance, the output power of the amplifier will also be different. In modern speakers, the standard values \u200b\u200bare 8, 6, 4 and 2 Ohms, and power levels are indicated for them.

Power per channel (4Ω)

The nominal sound power output by the amplifier per channel when a load with a dynamic resistance (impedance) of 4 ohms is connected to it. See Power per Channel (8Ω) for more information on power rating and its relationship to impedance.

Harmonic distortion

This indicator describes the amount of non-linear distortion introduced by the amplifier into the processed signal. Such distortions are not necessarily perceived as extraneous noise, but they degrade the quality of the sound anyway — for example, they can make it more deaf. It is almost impossible to avoid them, but it can be reduced to levels inaudible to the human ear.

As a result, the harmonic distortion factor (harmonics) is one of the main parameters describing the overall sound quality in Hi-Fi and Hi-End amplifiers. The lower it is, the clearer the sound. Hundredths of a percent are considered a good indicator for modern amplifiers, thousandths and below are excellent. The exceptions are tube and hybrid models, for which rather high harmonic coefficients are allowed; see "Element base" for more details.

Main input

The sensitivity and dynamic impedance of the amplifier when a signal is applied to the Main input.

Under the sensitivity of any input (except optical) is meant the lowest signal voltage at this input, at which the amplifier is able to provide normal nominal power values (see "Power per channel (8Ω)"). This parameter determines, first of all, the requirements for the signal source. On the one hand, the voltage provided by this source must not be lower than the input sensitivity of the amplifier, otherwise the latter simply will not give the claimed characteristics. However, a significant excess in voltage should not be allowed, otherwise the sound will begin to be distorted. More detailed recommendations on choosing an amplifier by sensitivity are described in special sources.

For any input other than optical, it is believed that the higher this indicator, the less distortion the amplifier introduces into the signal. The minimum level of input impedance in modern models is considered to be 10 kOhm, and in high-end devices it can reach several hundred kOhm.

Inputs

— Euroblock. Analogue audio input (usually line level) using a Euroblock connector. This connector, used mainly in professional audio equipment, is remarkable in that it is attached to the wire using terminals. This is extremely convenient when working with stripped wires (which is often required in professional applications): screwing such a wire to the plug once and connecting / disconnecting the plug to the Euroblock connector is much easier than constantly unscrewing / screwing the terminals. In addition, such a connection is often made balanced (see "XLR (balanced)" below). Inputs of this type are found mainly in information and information-concert amplifiers (see above).

— Phono. Dedicated input for connecting to the amplifier turntables; often has a suffix indicating the type of cartridge that is compatible, such as "Phono MM" or "Phono MM/MC" (see "Advanced — Phono Stage" for details). Despite the proliferation of digital formats, these players are still highly regarded by audiophiles for their high quality and fidelity, and are often used in premium audio systems. However, connecting a "turntable" has its own characteristics — in particular, it requires a phono stage (for more details, see ibid.) — and standard inputs are unsuitable for this purpose. Therefore, a Phono jack is a must if you want to connect your turntable directly, without an external phono stage.

USB B. The USB interface is widely used in com...puter technology for various peripherals. The presence of a type B input means that the amplifier can be connected to a computer as an external controlled device (slave). Most often, with this connection, it is used as an external sound card or audio interface — this provides higher sound quality and more extensive options for its settings than most built-in sound cards, even expensive ones. However, the matter is not limited to this: in some models, via USB type B, you can update the firmware or change the special parameters of the amplifier.

Coaxial S / P-DIF. Digital audio input, a variation of the S/P-DIF interface based on a conventional electrical signal (the second variation, optical, is described below). Usually uses a common RCA connector, known as a "tulip", but has rather strict cable requirements. The bandwidth of any version of S / P-DIF is quite sufficient even for high-quality multi-channel sound, and the coaxial version itself is simpler, cheaper and more reliable than the optical one, but more susceptible to interference.

Optical. Input for transmitting digital sound using light signals, via TOSLINK fiber optic cable; one of the versions of the S/P-DIF standard. The main advantage of optical fiber over traditional electrical cables is complete insensitivity to electrical interference; at the same time, it is more expensive and requires rather careful handling (in particular, it does not tolerate sharp bends).

— Balanced digital ( AES/EBU). The AES/EBU interface is used in the professional field to transmit audio in digital format. It can use several connection types; in this case, it means transmission over the so-called balanced line using an XLR connector. Both the principle of balanced connection and the connector itself are described in detail in the “XLR (balanced)” section below — however, in the case of AES / EBU, we are talking about a digital signal, not an analogue signal.

— COM port ( RS-232). A connector used to control the amplifier from a computer. Through it, you can change the settings, incl. and quite thin, and in some models even update the firmware. Usually, for such purposes, special software is required, which can be supplied with the amplifier.

Control input (IR). Connector for connecting an external infrared remote control receiver. When properly placed, such a receiver will allow you to use the remote control even in places where the signal from the remote control cannot reach the main (built-in) sensor — for example, in another room. For such purposes, not only sensors can be used as a separate device, but also system components that are compatible with the remote control — for example, players or tuners.

Outputs

— Preamplifier (Pre-Amp). The presence in the design of the device of a separate output for the signal from the preamplifier. In the type of amplifiers of the same name (see "Type"), such an output is available by definition and is the main, and sometimes the only one. On integrated models (see ibid.) , the Pre-Amp output allows you to connect an external power amplifier and use it instead of the internal one. This feature can be useful, for example, to connect a more powerful speaker instead of the original one, or to work in Bi-amping mode. It is worth noting that the Pre-Amp output can also be installed in power amplifiers, playing the role of a "splitter".

— Subwoofer. The presence in the amplifier design of a separate subwoofer output. Usually, such an output uses an RCA connector (see "Input to the amplifier (Main)"), and the function itself is implemented through a crossover, which selects the low-frequency range in the signal and redirects it to a subwoofer. The "own" output makes it much easier to connect a subwoofer : it does not require any additional equipment, the amplifier itself is enough. This usually provides for the possibility of working with any type of subwoofer — both passive and active; however, in the first case, you will need an additional external amplifier.

— Coaxial S/P-DIF. The presence in the design of the amplifier of the S / P-DIF output of an electric typ...e, with signal transmission via a coaxial cable. For more information about this interface, see the relevant paragraph in the "Inputs" section.

Optical. The presence in the design of the amplifier output for transmitting a digital audio signal over a fiber optic cable TOSLINK. For more information about this interface, see the relevant paragraph in the "Inputs" section.

Jack (6.35 mm). Presence of TRS type outputs in the design of the amplifier. These outputs are jacks for 6.35 mm Jack plugs and may look like the corresponding headphone jack (see below). However, this similarity is misleading: TRS produce sound on the principle of "one channel per plug" (an exception may be information amplifiers). This type of Jack connector is found mainly in high-end professional amplifiers.

Speakon. An interface used in professional audio equipment to connect acoustics to a power amplifier. It has become widespread in high power equipment, including concert amplifiers (see "Intended Use"), due to its increased reliability and suitability even for working with very powerful audio signals. But in household appliances it is rarely used.

Control output (IR). The control output allows the amplifier's built-in IR receiver to be used to control other components in the audio system, such as a DVD player in another room, out of range of the remote control, from the remote control. With this scheme of operation, the amplifier actually plays the role of a remote sensor, receiving commands and transmitting them through the control output to another device. Note that the very presence of such inputs and outputs does not guarantee the compatibility of various devices, especially if they are produced by different manufacturers; Sharing details should be clarified in the official documentation.

More features

— Direct connection ( By-pass/Direct). The ability to turn on the amplifier in By-pass / Direct mode. Its name is due to the fact that the signal is sent directly to the amplification stages, bypassing all additional controls (timbre, balance, etc.). Power amplifiers (see "Type"), by definition, use just such a scheme of operation. In integrated models, direct connection not only minimizes distortion in the processed signal, but also provides the sound closest to the original, which allows demanding listeners to appreciate the skill of sound engineers.

— Automatic power off. This function ensures that the amplifier automatically turns off if no signal is received from its input for a certain period of time. In this way, downtime is avoided — for example, if the owner left on business, forgetting to turn off the audio system. And considering that many modern amplifiers require a lot of energy even “at idle”, the savings can be quite significant. It is worth clarifying that in this case we are usually not talking about a complete shutdown, but about switching to standby mode; but the power consumption (see below) in this mode is usually so small that in fact the difference is practically not noticeable.

MM phono stage. The presence of a phono stage in the amplifier for working with turntables equipped with MM type pickups (with a moving magnet). The phono stage itself is a mandatory attr...ibute of models with a Phono input (see "Inputs"); its necessity is due to the fact that the signal from the pickups for vinyl has specific characteristics and needs additional processing. At the same time, two types of pickups can be used in modern record players — the already mentioned MM plus MC (with a moving coil), each with its own signal characteristics. Therefore, for the normal operation of the turntable, you will anyway need a phono stage of the appropriate type. Such equipment is also available as separate devices, but it is usually easier and cheaper to buy an amplifier with a built-in phono stage.

MS phono stage. The presence of a phono stage in the amplifier to work with turntables equipped with MC type pickups (moving coil). For more information about this function, see the subsection “MM Phono Stage” above.

Limiter. The presence of a limiter in the amplifier — a device that limits the dynamic range of the processed signal. This device is also called an "audio signal compressor" (due to the fact that it "compresses" the dynamic range). In simpler terms, a limiter essentially reduces the difference between the quietest and loudest sound output from an amplifier. This feature can be useful in any situation where you have to deal with uneven sound volume. For example, a limiter can make it more comfortable to listen to a symphony that has large volume differences — so that the listener can access the slightest nuances of sound and at the same time, loud fragments, as they say, do not beat on the ears. And for professional concert activity, the presence of a compressor is almost mandatory — in particular, to compensate for changes in volume that occur when the distance from the microphone to the acoustic instrument or the vocalist's mouth changes. Of course, the limiter can also be made as a separate device; however, its presence in the amplifier itself is sometimes more convenient. At the same time, this function is complex and expensive, and therefore is found mainly in professional equipment and top-class consumer models.

Connecting an additional speaker. The ability to connect an additional set of speakers (one or more) to the amplifier. Note that we are not talking about individual speakers, but about sets designed to work with full-length sound. In other words, if such an amplifier produces sound in stereo format at the main outputs (see "Number of channels"), then an additional set of acoustics will be able to work in this format. Models with this function are designed primarily for situations where you need to output sound to several rooms, and the signal can go either to all sets at once, or only to one at the user's choice. Also, an additional set of connectors can be used for Bi-Wiring (see below).

— Biwiring. Amplifiers with this feature use two separate channels of amplification for bass and treble, and are able to output each frequency band through a separate set of connectors. Due to this, it is possible to apply low-frequency and high-frequency signals via separate wires, and directly to the corresponding specialized speakers of the speaker system — instead of outputting a common signal to it and dividing it into frequencies using the built-in speaker crossover. In fact, this means that the Bi-Wiring connection reduces the likelihood of interference and improves the sound quality. However, keep in mind that this will require not only an amplifier, but also speakers that support this function. Note that Bi-Wiring is usually combined with the ability to connect an additional speaker described above.

— Management of external devices. The ability to use the amplifier as a control device for other components of the audio system — for example, preamplifier, turntable, etc. Control is usually carried out from the universal remote control supplied with the amplifier, and the control signal is transmitted through special connectors — this is much more convenient than adjusting each component separately. On the other hand, the construction of such systems is possible only from devices of the same manufacturer — different companies use different control standards, in most cases they are not compatible with each other.

— Bluetooth. A wireless communication technology with a range of about 10 m (more "long-range" versions are not used in amplifiers), originally created for direct connection between various devices. The functionality of such a connection may be different, but in this case, most often it is possible to broadcast to the sound amplifier from an external device — for example, a smartphone or laptop. However, other functions may be provided, for example, remote control from a mobile gadget through a special application.

— Emergency notification. The ability of the amplifier to work in an emergency warning system, more precisely, the availability of special functions and tools for working in such systems. Such tools may include, for example, connecting to fire detectors and automatically triggering warnings or evacuation messages to areas where the detectors have been triggered; selection of message type depending on the triggered sensor; connecting the notification microphone to the “priority input” and muting all other channels when sound is received from the microphone, etc. A specific set of features should be specified separately. Specialized security units may also be responsible for these functions, but sometimes it is more convenient to use an amplifier with built-in support for emergency notification.

Remote control

Possibility of operation of the amplifier with a remote control(the latter is supplied).

The advantages of this function are obvious: You do not have to approach the device every time in order to change the operating parameters. Moreover, some settings in modern models can only be accessed from the remote control. And separate amplifiers with this function have IR control outputs (see "Outputs") and can also work as sensors for transmitting commands to other devices. The remotes themselves can be made "learnable" — with the possibility of programming.

Power consumption

The power consumed by the amplifier during normal operation. Some manufacturers may indicate average power values, some — indicators at maximum load. However, anyway, this parameter allows you to quite adequately assess the power consumption of the device and the requirements for connected power.

In addition, it can be useful if you have doubts about the accuracy of the claimed data on the output power (see "Power per channel (8Ω)"). The basic rule is that the total power rating of all channels cannot exceed the total power consumption of the amplifier. In addition, there are special formulas that allow you to derive the maximum possible rated power depending on the power supply and type of amplifier; they can be found in special sources.
Pioneer A-30 often compared
Pioneer A-10 often compared