Comparison Sony HDR-AS50R vs Sony HDR-AS200VR

The presence of a 1/4" threaded socket on the camera body. It is this size that is standard for modern tripods and is used in most of these devices. So this feature allows you to mount the camera on a tripod without using adapters and other additional equipment.

The level of dust and water protection provided by the body of the camera itself. Most action cameras are designed for recording in extreme conditions, but the level of protection of each model can vary significantly — from the ability to shoot in the rain, to full tightness, allowing for a long immersion under water.

To characterize the security level of the camera, the international IP classification is used. Each device is assigned a code of the form IPXX, where instead of the first X — the level of protection against the ingress of foreign objects (including dust), and instead of the second X — the level of protection against the ingress of water.

Levels of protection against dust and foreign objects in modern action cameras are never lower than 5 — lower protection classes would provide unacceptably large gaps in the body. Specifically, level 5 provides that dust can get inside in small quantities, but does not affect the performance of the device. A higher level — 6 — provides full dustproof.

To characterize the level of protection from water, the following classification is used:

0 — no protection;
1 — drops of water falling at a right angle relative to the operating position of the device cannot cause dangerous consequences;
2 — protection against drops falling on the equipment at an angle of up to 15°;
3 — at an angle up to 60° (splash protection, minimum rain protection);
4 — protection from rai...n with strong wind;
5 — protection against water jets falling at any angle (water jets, for example, from a hose or heavy rain cannot harm the device);
6 — from temporary flooding;
7 — from temporary immersion under water to a depth of not more than 1 metre;
8 — from prolonged diving to depth (maximum time and depth are specified by the manufacturer separately).

In some cases, a model may only be IP-certified for one type of protection (only against sand or water). In this case, instead of the second parameter, simply X is put. So, for example, IPX6 security means that the camera is protected from temporary flooding and heavy rain, but the level of protection from dust is not defined and, accordingly, is not certified.

It is important to note that this parameter characterizes the protection of the camera itself, but does not take into account the capabilities of protective cases. Do not confuse it with the protection of the outer case, which sometimes comes with the device (see "Dust-, moisture-proof of case").

The number of megapixels in the action camera sensor, in other words, the resolution of this sensor(1 megapixel is 1 million photosensitive points).

There is an opinion that the higher the resolution, the better the image quality. It is true from the point of view that manufacturers are trying to install high-resolution sensors in advanced cameras. At the same time, there are no strict dependencies here, and from the technical point of view, the number of megapixels determines only the maximum image resolution that can be captured using this sensor. The quality of this picture will depend both on several features of the sensor itself (size, type, special design solutions), and the specs of the camera. So when choosing, you should focus not so much on the resolution of the image sensor, but on the general class of the camera and reviews with examples of footage.

The maximum resolution at which the action camera can take photos. Specified in pixels horizontally and vertically.

This parameter is directly related to the resolution of the image sensor(see above): the total number of pixels in the photo, usually, corresponds to the number of pixels in the sensor. For example, a photo resolution of 4608x3456 corresponds to a sensor of 15925248 pixels, or approximately 16 megapixels. If the number of pixels in the photo is greater than the claimed resolution of the sensor, then the manufacturer uses software tricks that allow you to improve the photo resolution to a higher one than originally. This reduces the cost of devices but also affects the quality of images.

Theoretically, high-resolution images can provide good detail, but in fact, much depends on the specs of the sensor (primarily physical size) and image processing features.

— Photo during video. The ability to take photos directly while recording a video — usually using a separate button. Thus, it is convenient to fix the most significant moments of what is happening. Such photos are much better in quality than "freeze frames" from the captured video.

— Serial photo shoot. This feature allows you to take several pictures at once in a short period (usually it is a fraction of a second). A series of shots increases the chance of capturing a good moment, which can be very important given the specifics of using action cameras.

— One click recording. The ability to quickly turn on the camera for recording — literally at the touch of a button, by the name. Moreover, such a button works even if the device is turned off. However, the recording inevitably starts with some delay; but often this delay is a fraction of a second.

— Online streaming. Ability to stream video to popular services like YouTube and social networks (Facebook, Instagram, TikTok, etc.). Usually, the online streaming function is implemented when the action camera is connected to the Internet via a Wi-Fi network, less often via a wired connection. Communication with the World Wide Web can be held directly or through a smartphone or computer. It will require the use of appropriate software.

— Time lapse. A special mode of operation of the action camera, in which video recording is carried out at a slower frequency is mainly used for filming slow processes. Thus, for example, a long journey or a long sunset can fit into a 3-minute video.

— Auto-rotate. The function of automatic rotation of the captured photos and videos to the position corresponding to the position of the camera. Without this feature, all footage during playback would be displayed strictly in landscape orientation, and footage shot with the camera upside down or upside down would have to be rotated in a photo or video editor. Usually, at the beginning of video recording, auto-rotation is blocked — so that the position of the frame at any time corresponds to the rotation of the camera itself relative to its original position.

— Photo panoramas shooting. The ability to use the camera to take panoramic photos. In traditional action cameras (see "Product type"), such shooting is carried out as follows: the camera takes several separate photos, which are then glued into one image. Regarding panoramic and 360-degree models (see ibid.), it is worth noting that not all such models support shooting in panoramic format, so it is advisable to check the availability of this function separately.

— Key points labels. The ability to add special marks to the footage that indicate key moments. While viewing such videos, you can go directly to the labels — this is easier than manually searching for the right moment. This feature is especially useful when shooting long videos, as well as when numerous individual files. The label, usually, is placed right during the shooting by pressing a special button or by voice command.

— Night shooting. Special mode for recording in low light conditions. The specific implementation of this function may be different: in some models, the sensitivity of the sensor is increased, in others, shooting in the IR range is used. Accordingly, specific features may vary: not every camera with this function can shoot in complete darkness, and these nuances should be clarified separately.

— GPS module. Built-in satellite navigation module that allows you to determine the current coordinates of the device. Options for using data from GPS can be different: geotagging footage, recording travelled routes, determining the speed of movement, or even full-fledged navigation on the map.

— Wi-Fi module. The Wi-Fi wireless module in action cameras can be used in different formats: in some models, it is responsible for connecting to the Internet, in others it is for communicating with a smartphone or other gadget, in others both options are available at once. Anyway, the main use of this connection is to transfer footage to an external device or to the Internet (including broadcasting in the online streaming format, see “Filming capabilities”). In addition, more specific functions can be provided, for example, using a smartphone as an external viewfinder and remote control. Specific features of the use of Wi-Fi in each case should be clarified separately.

— Bluetooth. Direct wireless communication technology for exchanging information between two electronic devices. In action cameras, it is most often used to connect remote controls, selfie sticks and smartphones, which can also act as a remote control. Unlike the Wi-Fi module, it consumes battery power more economically, but at the same time, the range of wireless communication is reduced to 10 m...etres.

— NFC chip. NFC is a wireless communication technology over short distances (up to 10 cm). In action cameras, this technology is mainly used as an auxiliary one, to facilitate connection with a smartphone or other gadget via Wi-Fi or Bluetooth. If such a gadget is also equipped with NFC, just bring the camera to it and confirm the connection — it's easier than fiddling with the settings.

— USB-C. A relatively new type of USB interface that uses a miniature double-sided connector, slightly larger than microUSB. Most often used for similar purposes — as a universal connector through which you can charge the battery and connect the camera to a computer (for copying photos and videos, updating software, etc.). P.). At the same time, USB-C provides a higher data transfer rate than microUSB, supports more power supply, and also has a more convenient plug. Occasionally, there are more specific ways to use this interface — for example, direct connection to a smartphone or tablet that has a USB-C port.

— HDMI output. HDMI is a digital interface specially designed for high-definition video and multi-channel audio. With this output, you can connect the camera to a TV, monitor or other device as an external player and play the footage directly. The convenience of HDMI is that almost all modern video equipment with support for HD standards is equipped with such inputs.

Note that the cameras can be equipped with a smaller version of the connector — miniHDMI or microHDMI; however, finding an adapter cable is usually not a problem, it can even be supplied in the kit.

— Microphone connection. Almost any modern action camera has a built-in microphone that allows you to record sound. However, the quality of its sound is often quite low. Thus, many models can connect an external microphone — you can fix it, for example, on the helmet strap and record the comments of the athlete in the process of movement. Note that different types of connectors can be used for such a connection. As a result, the specific connector type and supported accessories depend on the action camera model, and some devices are only compatible with branded microphones.

Speaker or speakers installed directly in the camera body. This function is mainly intended to allow you to view footage with sound without connecting headphones or external speakers. However the built-in speakers do not have decent volume or general sound quality — nevertheless, they allow you to determine what the camera “heard” as a whole, whether sound recording was turned on, whether individual ambient sounds got into the recording, etc.

The largest memory card capacity supported by the camera model.

This limitation is due to two points. First, the larger the drive, the more computing power is required to use it. Secondly, each type of memory card has its maximum capacity. For example, the capacity of an SD HC card cannot exceed 32 GB, larger drives already belong to the SD XC standard, and if it is not supported, the maximum card capacity cannot exceed 32 GB.

It is strongly not recommended to exceed the maximum allowable capacity: even if the card is recognized by the device, its normal operation is not guaranteed.

— Protective case. A special container that provides additional protection from dust, moisture, impacts, extreme temperatures and other similar "troubles". The specific level of protection in each case should be specified separately. In order not to interfere with filming, the box is made of transparent materials. In addition, we note that some cameras can only be mounted on mounts in a box (or in a mounting frame - see below), since the body itself may not have space for this.

— Mounting frame. A device designed to install a camera on various mounts — helmet, steering wheel, etc. The camera body itself often does not have "landing sites" for such mounts, which is why additional equipment has to be used. Note that a protective box (see above) often performs a similar function; the mounting frame, in contrast, provides almost no protection, but the camera body remains maximally open in the frame. This provides additional opportunities — in particular, it allows you to connect various cables and effectively use the built-in microphone, which is impossible when using many boxes.

— Helmet mount. A mount designed to mount a camera to a helmet or other curved surface. The design of such a mount is based on a curved platform with an adhesive layer or Velcro, the shape of which roughly matches the shape of the helmet surface. Such a device can provide a more s...ecure hold than a classic flat platform (see below).

— Flat mount. One of the main and simplest mounts used to fix an action camera to almost any uniform surface: snowboard, skateboard, car hood, etc. It is a small flat platform, to one side of which the camera is attached, while the second is fixed to the desired surface (using Velcro, special glue, etc.). Note that flat mounts are often used for installation on a helmet, but for this purpose there is a separate type of mount, with a curved platform (see above).

— 3-axis mount. This differs from other types of mounts by the presence of three movable units that allow you to rotate the camera at an angle of up to 90 degrees in three axes. In practice, this allows you to choose the most interesting or successful shooting angle - on the side of the helmet, for example. Such solutions are usually compatible with many other mounts, so they can be used together with a steering wheel, curved, etc.

— On the handlebars of a bicycle/motorcycle (pipe). A mount for installing a camera on a small pipe — for example, the handlebars of a bicycle or motorcycle. As a rule, it works on the principle of a clamp, and the size of the mount can be adjusted within a fairly wide range, adjusting it for pipes of different diameters.

— Suction cup(on glass). A camera mount that is fixed in the desired location using a suction cup. Allows you to install the device on flat and slightly curved surfaces. It is worth considering that such mounts do not hold as securely as flat or curved ones (see the relevant points). On the other hand, the suction cup is easy to attach and remove and leaves no marks. Therefore, mounts of this type are mainly used for installation on car glass when the camera operates as a video recorder.

— Clamp (clip). The clip-type mount is quite universal, since it allows you to hang the camera on almost any suitable piece of equipment (backpack strap, unloading belt, belt, etc.). However, it is not very suitable for extreme shooting due to its relatively low reliability.

— Head mount. A device for fixing the camera to the head — usually on the forehead, like a headlamp. In addition to freeing up your hands, this placement has another advantage: the camera lens looks in the same direction as the customer. The mount itself is usually a system of elastic straps and is designed to be worn directly on the head, as opposed to a curved helmet platform. However, some models allow the possibility of wearing it over a helmet.

— Chest mount. This mount is a system of elastic straps that allows you to fix the camera on the customer's chest, shooting slightly lower than "from the eyes". Like the head mount (see above), it is easily adapted to the desired size.

— Monopod(selfie). A device commonly known as a “selfie stick”. It is a rod, usually foldable and sometimes adjustable in length; at one end of the rod there is a mount for the camera, at the other - a handle for holding in the hand. In accordance with the name, such a monopod is intended mainly for filming yourself - thanks to the length of the rod, the camera can be held at a comfortable distance. However, other ways of using it are possible: for example, with the help of a monopod you can “look” quite far over the edge of a cliff or around a corner. The main disadvantage of such a device is that one hand is constantly occupied.

In addition to those described above, the delivery set may also include other types of fastenings - for example, for musical instruments (on the neck of a guitar, on the bar of a drum kit, etc.), on a surfboard, etc.