Guide number
The guide number is the main characteristic that describes the power of the light pulse of the flash. It is described as the maximum distance (in metres) at which, at ISO 100 and f/1 lens speed (aperture 1), a flash is able to illuminate an "average" subject sufficiently for a normal exposure; in other words, at what distance from the flash it will be possible to normally shoot the scene at the specified ISO and aperture.
There are formulas by which, knowing the guide number, you can derive the practical shooting distance for each specific value of sensitivity and aperture. The simplest formula used to calculate the distance at ISO 100 is: S=N/f, where S is the distance, N is the guide number, f is the aperture value. For example, for a guide number of 56 and an f/2.8 lens, this distance would be 56/2.8 = 20 m. Increasing or decreasing sensitivity by a factor of 2 would increase or decrease the specified distance by approximately 1.4 times, respectively. If you need to calculate the distance as accurately as possible, you should refer to more detailed formulas that can be found in specialized sources.
Separately, it is worth noting that the leading numbers of flashes, usually, are indicated by manufacturers for specific focal lengths of lenses. This is due to the fact that the shorter the focal length and, accordingly, the wider the viewing angle, the more light is needed to illuminate the scene being shot and the more powerful the flash pulse should b...e (at the same distance). Therefore, when choosing by the guide number, it makes sense to pay attention to the focal length indicated by the manufacturer and select a model with a power reserve — especially since guide numbers are often prescribed for rather “long-range” lenses (with a focal length of about 80-100 mm in equiv. 35 mm).
Reload time
The time it takes the flash or generator (for studio flashes) to prepare for the next flash. The smaller it is, the better. This parameter is especially important for continuous shooting, when the interval between frames is small: if you often shoot in this mode, you should look for a flash with the shortest possible recycle time. Also note that the characteristics usually indicate the shortest recharge time; in some operating modes, it may be significantly more than stated.
Pulse duration
The duration of the pulse of light provided by the flash. This indicator can range from thousandths to hundred thousandths of a second; it is usually expressed as a fractional number with a unit in the numerator, such as 1/880 s. The human eye does not notice the difference, but in some shooting modes it can become critical. For example, to capture fast-moving scenes (such as splashing water, the flight of an insect, or the movement of machine parts) you need to choose a flash with the shortest flash duration possible — otherwise the image may be blurry.
The longest pulse duration in modern photoflashes is about 1/800 s; the minimum value can reach 1/30,000 s or even less.
Features
—
Autofocus illuminator. The flash has an auxiliary illumination function for the camera's autofocus system. Modern cameras overwhelmingly use the so-called passive autofocus systems that have one serious drawback: very low efficiency in low light and/or low contrast of the object being shot. The autofocus illuminator is designed to solve this problem: before focus, the scene is illuminated by a separate lamp, placed, in this case, directly in the flash body. This provides enough light for normal autofocus operation. Most often, backlight lamps give light with a characteristic reddish tint, however, in some advanced models, infrared illumination is used — invisible to the eye, but perceived by the camera. In addition, illumination systems can use a special light pattern instead of a solid beam, which further simplifies the task of autofocus systems. Anyway, the presence of this function is especially relevant given the fact that the flash is often used as a light source in low light.
— Control on the camera. The ability to change the settings for the flash using the controls of the camera itself, to which it is connected. In some cases (for example, with a wireless connection), this is much more convenient than switching attention from the camera to the flash.
—
Automatic zoom. The ability to automatically change the angle of dispersion of the flash light. For the angle of dispersion,
...see the relevant paragraph above, but here we note that this function provides synchronization between the flash and the lens: when the focal length of the lens changes, the angle of dispersion automatically changes. This provides the most effective illumination of the scene and at the same time relieves you of the need to manually re-adjust the flash to a changed angle of view each time.
— Manual zoom. Possibility to change the flash spread angle (see "Light spread angle") manually. This function expands the possibilities for "fine" tuning of work parameters and allows you to set parameters that are not available with automatic zoom (see above). In addition, it will be useful if you have to use several prime lenses with different focal lengths — the flash can be easily adjusted to each of them.
— Wireless control. Ability to wirelessly connect the flash to the camera or to another flash as master/slave (if available, see below). The format and specific features of such a connection may be different: wired connection, IR channel, radio, etc. Wireless control is indispensable if the flash must be placed away from the camera; it also makes it easier to create multiple flash systems for optimum lighting. These features are especially useful for studio shooting (although it's not limited to this).
— Work in master mode. The ability to operate the flash as a master flash for a system of multiple flashes. The entire system is controlled through the master flash, the operation parameters of the slave flashes are set, and the command to fire is given (note that the master flash itself may not fire at all). If you plan to shoot using a multi-flash system, you will definitely need a model with this function — without it, creating a system is impossible. Of course, master and slave flashes must be mutually compatible; this point should be clarified separately.
— Work in slave mode. The ability to work as a flash as a slave in a system of several flashes. In this mode, the device is connected to the master flash and fires on command from it. For more information on flash systems, see "Master Operation" above.
— Diffuser. The colour of the diffuser supplied with the on-camera light source (see "Type"). Colour can be: orange, white, pink or yellow.
A diffuser is a special filter designed to scatter light from individual LEDs, and also, in some cases, to give it a certain colour and change the colour temperature.
— Radio synchronizer. A device designed to wirelessly control a flash or a set of flashes (if each has its own receiver). Usually a separate module installed in the hot shoe; on command to fire, this module sends a radio signal to all receivers tuned to it, ensuring synchronous flash firing. At the same time, some models of luminaires with such a function are capable of receiving via the radio channel not only the start signal, but also the operating parameters (primarily the duration and power of the pulse).
