Comparison Barska AR-X 1x35 vs Konus SightPro TR

The offset is the distance between the eyepiece lens and the exit pupil of an optical instrument (see "Exit Pupil Diameter"). Optimum image quality is achieved when the exit pupil is projected directly into the observer's eye; so from a practical point of view, offset is the distance from the eye to the eyepiece lens that provides the best visibility and does not darken the edges (vignetting). A large offset is especially important if the sight is planned to be used simultaneously with glasses — after all, in such cases it is not possible to bring the eyepiece close to the eye, and it must be at some distance from the glasses so as not to hit the glass due to recoil.

The diameter of the area visible through the sight from a distance of 100 m — in other words, the largest distance between two points at which they can be seen simultaneously from this distance. It is also called "linear field of view". This indicator is more convenient for many users than the angular field of view (the angle between the lines connecting the lens and the extreme points of the visible image) — it very clearly describes the capabilities of the device.

In sights with magnification adjustment (see above), both the entire range of width — from maximum to minimum — or only one value of this parameter can be indicated. In the latter case, the largest width of the field of view is usually taken, at the minimum magnification.

Units of measurement of angles used in the scope - primarily for making corrections using the drums. The same units are often used in marking the goniometric elements of the aiming reticle (see “Measuring units of the reticle”), but there are exceptions, so it would not hurt to clarify this point separately. Nowadays there are two main units:

- MOA. Abbreviation for minute of arc - 1/60th of a degree. Originally, this unit is associated with the English system of measures and is convenient primarily for calculations in yards and inches: at a distance of 100 yards, an angle of 1 MOA corresponds to a linear dimension of approximately 1 ". In the metric system, which is more familiar to us, this gives 2.91 cm at a distance of 100 m. We also note that this unit is a kind of accuracy standard: it is believed that a full-fledged sniper rifle should give a spread of no more than 1 MOA.

—MRAD. The symbol for a milliradian is an angle of one thousandth of a radian (approximately 0.06°). Also in sniper jargon, this unit is called “thousandth”, or “mil”. It is already tied to the metric system: at a distance of 100 m, an angle of 1 MRAD corresponds to a linear dimension of 10 cm (approximately 3.5 times more than 1 MOA).

The choice based on this indicator largely depends on the personal preferences of the shooter. And although “thousands” are generally more convenient for domestic use...rs, with minimal experience you can successfully use MOA, and also switch between these units and convert one to another without much difficulty. So in general this point is not particularly important.

The division value of the turrets used in the sight to enter corrections.

The increment value for the correction turret is the angle that the point of impact shifts when rotated by 1 click (“click”). In this case, this angle is indicated in MOA — minutes of arc. For more information about this unit, see "Measuring units of the sight"; and the lower the division value, the more accurately you can set up the sight initially and make corrections in the future. For example, if this indicator is 0.5 MOA — each click will shift the point of impact by about 1.46 cm for every 100 m of distance (that is, 2.91 cm at a distance of 200 m, 4.4 cm at 300 m and so on); and 0.25 MOA will already give only 7.3 mm per click for every 100 m.

The smaller the step and the more accurate the adjustment system, the more expensive it is. Therefore, when choosing, it is worth taking into account the features of the planned application — first of all, the size of the targets and the distance to them; detailed recommendations on this matter are in various manuals on shooting. If we talk about specific values, then the mentioned 0.5 (1/2) MOA are typical mainly for inexpensive and medium scopes, 0.25 (1/4) MOA is a pretty good indicator, and the advanced optics itself allows adjustment in increments of 0.125 (1/8) MOA.

A type of coating used in scope lenses. Anyway, we are talking about the so-called antireflection coating, which is the thinnest film (single or multilayer) on the surface of the lens in contact with air. The properties of this film are chosen in such a way as to minimize the reflection of light from the glass surface. The meaning of this function is not so much to reduce the brightness of glare that can unmask the shooter, but to increase the light transmission of the optics and, accordingly, the quality of the image visible through it.

Modern sights can be equipped with the following types of coatings:

— Illuminating. In this case, the simplest option is implied — an incomplete single-layer coating. The term "incomplete" means that not all lens surfaces are coated (although there may be several coated surfaces). Such enlightenment is inexpensive, however, the image quality is relatively low — in particular, because a single-layer film is most effective only for a part of the visible colour spectrum.

— Full illumination. Fully coated means that all surfaces of the lenses that come into contact with air have a special coating; in this case it is single layer. Such a coating is more expensive than a simple anti-reflective coating, but the quality of the “picture” when using it is higher, because. light distortion at the transitions between glass and air is minimized.

— Multi-layered illuminating. Incomplete AR coating (see above)...using multilayer films. Thanks to multiple layers, the anti-reflective coating covers the entire visible spectrum, which allows you to achieve a brighter image with less colour distortion compared to single-layer coatings; However the price of such devices is higher.

— Full multilayer enlightenment. The most advanced option: multilayer coating on all lens surfaces used in the design of the sight. Features of full and multi-layer coating are described separately above. Here we note that their combination is typical for high-class sights, because. it provides the highest quality image, but it is not cheap.

The type of aiming mark (reticle) provided in the device. There are models for which several options are indicated at once: this implies the possibility of switching between them.

As for specific varieties, in collimators, all brands have a common specificity - they should provide the convenience of quick aiming at relatively short distances. But the reticles of optical and other similar sights can be divided into hunting and tactical (sniper) sights. The former are relatively simple and have a minimum of additional elements, as they are designed for short distances and relatively large targets; and the latter are designed for high-precision shooting, military and police use, and therefore must be supplemented with various elements for measuring angles and taking corrections on the go, including between shots.

Among the specific types of grids most popular in our time are the cross with divisions, BDC, duplex, cross, half-cross, cross with a dot, cross with a circle, herringbone, rangefinder, dot, circle with a dot and circle with 2 points. Here are th...e main features of each:

— Cross with divisions. One of the most popular types of "tactical" reticles used in optical sights. The key element is the crosshair, on the lines of which additional dots are applied. The distance between the points corresponds to a strictly defined angular size; initially it was 1 MRAD (1 "mil", hence the name), however, in modern sights, other values \u200b\u200bcan be found, they should be specified according to the instructions. In addition, such grids can differ in the number of points, the presence of thickening on the lines (as in the duplexes described below), etc. Be that as it may, such a grid is very convenient for estimating distances and making corrections on the fly, many professional shooters consider it almost ideal for high-precision shooting, including at long distances, besides, the original cross with divisions (Mil-Dot) is widely used by military and police snipers around the world.
We also note that there is also a collimator variety of "mildots" - in this case, the grid looks like a circle with a dot in the middle and several dots below it, with an interval of the same 1 MRAD. However, when using collimators, the real need for making vertical corrections rarely arises, and this option is not widely used.

- Duplex. Reticles for optical and night sights (see "Type"), which look like a classic crosshair with different line thicknesses: they are thin in the center, and noticeably thicker near the edges. The meaning of this combination is that thin lines do not “clutter up” the field of view at the aiming point, and thick lines remain visible even under adverse conditions (for example, at dusk) and allow you to aim at least approximately. In addition, the thickness of large lines and the distance between their edges can correspond to well-defined angles, which allows some of these sights to be used even as simple goniometers. However, these possibilities are very limited, and in general, "duplexes" are classic hunting nets.

- Half cross. Hunting net, the main elements of which are T-shaped. One of the varieties of semi-crosses - "German grid", it is also "stump" - consists of a vertical line from the edge to the center of the sight and two horizontal lines that do not reach it; the aiming point corresponds to the upper point of the central "stump", and the thickness of the lines and the distance between them can be specified in the documentation - this allows you to carry out the simplest measurements of angles. A more modern version of the half-cross is the crosshair, in which one line (from the center to the top edge) is much thinner than the rest, or even absent altogether.

- Dot. In its pure form, the dot is used exclusively in collimator sights (see "Type"). This is an extremely convenient option for such devices: there are no unnecessary details in the field of view of the shooter, only a mark that clearly shows exactly where the weapon is aimed - more is often not required when using collimators. The disadvantages of the dot in comparison with other marks in the sights of this type include less visibility, especially in bright ambient light. However, many sights allow you to set a fairly high brightness of the mark, and sometimes even increase its size, increasing visibility. Also note that for a point, the angular size can be specified, which can be useful for quick estimation of distances.
In addition, the dot can also be used in optical and night sights, but in such cases it is usually used as an addition to another scale - for example, it additionally highlights the intersection of lines in a semi-cross.

— Circle with a dot. Another type of marks, used in collimators as the main one, and in other types of sights - as an addition to a crosshair or other more traditional grid. However, the latter is rare, so let's focus on the first option. Compared to another popular "collimator" mark - a dot - the circle covers more visible space, however, it is very noticeable and often turns out to be more convenient when shooting offhand or sharply turning the weapon to the side. In addition, for both the circle and the dot, it often indicates the exact angular size, which gives extended (compared to the usual dot) possibilities for using the aiming mark as the simplest goniometric (rangefinding) scale.

- Circle with 2 dots. A variation of the circle with a point described on top, having a second, additional point - usually below the first, at a strictly defined angular distance from it. This expands the possibilities for using the sight as an impromptu rangefinder, and also allows you to "on the move" take an amendment when shooting at long distances - just aim at the second, lower point. However, such opportunities for collimators are extremely rarely required, so this option has not received much distribution either.

- Cross. Features of this type of brand depend on the type of sights in question - optical / night or collimator (see "Type"). In classical optics, a cross is the simplest crosshair of thin lines of the same thickness. Naturally, in terms of general specialization, such reticles are hunting, but they are also found in a fairly advanced variety of sights - sports models for benchrest (shooting from a machine gun at maximum range and accuracy). The convenience of the cross in such an application lies in the fact that the lines have a minimum thickness and practically do not block the view. In nightlights, this type of grid is usually one of several options available to choose from. But in collimators, the cross is in many ways similar to a circle with a dot - it is provided as one of the large, well-marked marks with a clearly defined angular size.

- Cross with a dot. A grid in the form of a crosshair of two lines (as a rule, quite thin), at the intersection of which a clearly visible point is applied. It is in this form, as a rule, that is used in collimator and other types of sights. In the first case, such a stamp is actually a slightly modified version of the usual cross (see on top). And in optics, the presence of a point allows you to additionally highlight the crosshairs, which is convenient in some situations; the general purpose of such sights is, of course, hunting.

- A cross with a circle. Stamp in the form of a cross, complemented by a circle. It can also be used in different types of sights and has its own specialization everywhere. In classical optics, such a grid usually has a hunting purpose, although there are also varieties with additional marks that expand the "tactical" functions. And even in the absence of such marks in the characteristics, the angular size of the circle is usually specified, which provides additional opportunities for impromptu measurement of distances. We also note that the cross itself can be both ordinary and duplex (see on top). The situation is similar in night sights, however, there a cross with a circle is usually only one of the available mark options. As for the collimators, they can use both a full-fledged crosshair in a circle, and a ring with “rays” protruding from it; in any case, such a mark is more noticeable than an ordinary cross.

— BDC. This reticle got its name from the English phrase Bullet Drop Compensation, which translates as “bullet drop compensation”. The BDC ballistic reticle allows for range correction based on the bullet's trajectory. It is calibrated for a specific ammunition and sharpened for quick aiming at various distances using the same type of bullets. Distance markers in a ballistic reticle are hash marks, circles, or dots. The main sign of their placement is that the vertical markings have different gaps, increasing towards the bottom. An additional distance scale is often placed in such grids on the "six" shoulder. In addition, the ammunition for which the reticle is calibrated is usually indicated (caliber, bullet weight, weight).

- Christmas tree. Informative reticle resembling a Christmas tree in its structure. Actually, this is where the name of this type of grid came from. Each array of dots on its "six o'clock" arm is longer than the previous one - the marks increase in width when viewed from top to bottom from the central crosshair. These markers are used to correct for wind drift, which is extremely important when conducting aimed fire at long distances. The most common herringbone reticle is found in hunting hybrids, tactical sights, and military rifle scopes.

- Rangefinder. This type includes all grids that do not belong to any of the types described on top and provide for special markings for measuring angles and distances. The specific design of such markings may be different, but the general principle of operation is the same everywhere: rangefinder marks allow you to determine the angular size of a visible object, and if the linear size of this object is known, you can easily estimate the distance to it (at least approximately). Each type of rangefinder reticle has its own rules for use.

The type of mount supplied with the scope.

For normal mounting on a weapon, this mount must match the type of seat for the scope. The most popular types of mounts nowadays are on the Weaver / Picatinny rail and on the dovetail ; branded latches are noticeably less common, and some sights are supplied without mounts at all — this allows you to choose the option at your discretion. Here is a detailed description of specific options:

— On the Weaver / Picatinny rail. Fastening on a standard bar (“rail”) Weaver or Picatinny rail. It is considered the Western standard for installing a weapon body kit, but nowadays it is widely used around the world. It is worth noting that these types of slats, although similar in design, are not the same. They both have a T-shaped profile and transverse slots that allow you to securely fix the installed accessory in the chosen place, but differ in the size and location of these slots: they are wider in Picatinny rails and have a standard distance between centers. In fact, this leads to the fact that accessories for Weaver rails can easily fit on Picatinny rails, but not vice versa. In addition, Picatinny is considered more of a military standard, and civilian weapons are equipped mainly with Weaver rails. Thus, most of the complete rail mounts found among modern sights are designed specifi...cally for the Weaver rail, as it is more common and universal. However, exceptions are possible, so this nuance needs to be specified separately.

— "Dovetail". The seat of this type has a cross-sectional view of an inverted trapezoid, and the mount provides protrusions on both sides, which, when the sight is installed, “cover” this trapezoid. This type of mount is found mainly in air and sporting rifles, as well as in hunting weapons of a classic design. In the latter case, this choice is also due to aesthetic considerations — these mounts look neater than the gear "rails" of Weaver and Picatinny rails.

— Firm. Various specific fastenings not related to the standards described above. Often they are made not just for the products of a particular brand, but also for strictly defined models of weapons; one of the characteristic examples is the original seat on the high-end "sniper" Blaser R93. Branded devices can have a rather original design — for example, in some collimators for shotguns, a plate is used that is fixed between the butt and the receiver. In general, due to limitations in application, such fasteners are usually provided not as the only option, but as one of the options, in addition to the bar and/or dovetail.

Separately, it is worth touching on situations where several types of mounts are indicated in the characteristics of the sight at once. Most often this means that this model is available in different configurations, but there are other, more specific options — the presence of several types of mounts in the kit at once, an adapter from one type to another, or even a universal retainer that is also compatible with Weaver / Picatinny rails, and with a dovetail. Such details in each case should be clarified separately.

The country of origin of the brand under which the product is sold. Nowadays, the sights market is mainly represented by brands from such countries (in alphabetical order): Belarus, Great Britain, Germany, Spain, Lithuania, USA, Japan. However, there are other options as well.

There are many stereotypes about how the origin of a particular country affects the quality; however, nowadays, they have practically no basis. First, the origin of the brand is indicated either by the actual place of origin of the company, or by the country in which its headquarters is located; in both cases, this country does not always coincide with the country where the production is located and where the device was actually manufactured. For example, it is quite normal for the products of an American or German brand to be manufactured in Taiwan or Turkey. Secondly, the actual quality of a product is primarily affected by how it is positioned in the market and how carefully the manufacturer ensures quality control. As a result, paying attention to the "homeland" of the brand makes sense only when you fundamentally want or do not want to support a company from a certain country; in other cases, it is worth focus primarily on the reputation of a particular...manufacturer.

The total length of the sight.

This parameter is important primarily for optical sights (see "Type"). Such devices can be quite large — from 20 – 30 cm in the most compact models up to 40 cm or more ; and the distance from the eyepiece to the eye when aiming must be strictly defined. So before buying, it's ok to clarify whether it will be possible to correctly place the selected model on the weapon. But collimators, even the largest ones, are very compact, usually there are no problems with their installation, so in such models the length does not play a special role.