Comparison Treker MAT-100 vs High Peak Minilite 2

Seasons in which the use of a tent is allowed.

There are three main seasonality options: winter, spring / autumn and summer. At the same time, the design features necessary for comfortable use of the tent in different seasons are as follows:

— In winter, the tent should effectively protect against snow and wind, and its materials and fittings should normally endure a long stay in the cold. Thermal insulation is also desirable, but in general this is a secondary factor — the main insulation is provided primarily by clothing, a sleeping bag and a bed.
— In the off-season — in spring and autumn — protection from rain, which can be accompanied by strong winds, is of particular importance.
— For comfortable use in the summer heat, good ventilation is required, ideally with insect protection, such as mosquito nets.

As you can see, these requirements generally do not contradict each other and may well be combined in one product. Thus, there are very few tents on the market designed strictly for one season — two- or even all-season options are much more common. For example, even among beach tents (see "Purpose") there are models for which the possibility of using in the off-season is claimed — for this, the design provides for a dense awning, or even the ability to completely close the tent. Almost any model from the "spring-autumn" series...additionally has a summer specialization; and most models suitable for winter actually allow year-round use.

In conclusion, we recall that tents with the same seasonality and purpose can at the same time differ significantly in characteristics and design features.

— Hemisphere. Tents with a frame of two (sometimes more) crossed arches. The main advantage of such a case is good resistance to wind. On the other hand, the interior space of the hemispheres is relatively small.

— Half -shell. In cross section, the semi-barrel has the shape of a half circle (or more or less similar), and its frame consists of several semicircular arcs arranged in parallel. This provides a good internal volume, but the wind resistance of this type of hull is lower than that of hemispheres (which, however, is not critical in conditions of plains and low mountains, where there are no storm winds).

— Shatrovaya. In such a case, one rack is used, located in the middle, and the tent itself has the shape of a pyramid or cone. The advantage of tents is their high height, the disadvantage is the inconvenience due to the presence of a rack inside the living space and poor resistance to wind. This form is quite rare.

— Double. The upper part of such a body is a rib, from which two sides of the awning (slopes) diverge at an angle. To create this shape, two internal supports are usually used at the ends of the tent. This design provides additional water resistance, because. the awning is located at a large angle to the drops falling from above; at the same time, due to the inconvenience created by the...supports located inside, and a number of other features, such tents are very rare.

— Cube. A hull shape found only in fishing tents (see "Intended Use"). Almost all such models are intended for winter use and ice fishing. At the same time, some of them do not have a bottom or are equipped with a hole in the bottom, which allows you to install an awning directly above the hole; others are closed from all sides, including from below, and fishing is supposed to be through the opening. However, among the cubic tents there are also demi-season/summer models, including advanced solutions for carp fishing.

The wind valve allows you to close the ventilation window to prevent snow or rain from getting inside. Its name is due to the fact that ventilation windows usually do not allow precipitation falling strictly vertically (in calm weather), but a strong wind can bring drops or snowflakes inside.

— External. The external frame is considered more convenient to set up, especially in the case of double-layer tents (see "Inner tent"), since both the inner tent and the outer awning are put on the frame at once. On the other hand, such a frame is more susceptible to the negative influence of natural conditions and does not allow the inner tent to be set up separately.

— Internal. The internal frame is somewhat more difficult to install than the external one; at the same time, it is less susceptible to the influence of unfavorable external conditions, and in double-layer tents (see "Inner tent") with an internal frame, it is usually possible to install only the inner tent, without an awning.

It should be noted that only tents in the shape of a hemisphere or half-barrel have a classic frame (see "Body shape"); in the case of gable tents, the characteristic "external/internal" refers primarily to the location of the supports, and the term "frame" is not applied at all to tent models.

— Inflatable. In such tents, the role of the frame is played by sealed hollow tubes made of flexible material (rubber or polymers), usually arched. When folded, they can be rolled up quite compactly, and when the tent is set up, they are inflated (usually with a special pump), acquiring the desired shape and sufficient rigidity to support the awning. The advantages of inflatable frames are their...light weight and ease of installation; they usually belong to quick-setup systems (see above for the latter). On the other hand, inflatable elements are very sensitive to damage: a small crack or hole, not critical for an element of a regular frame, disrupts the seal and makes the tent unusable.

— Pop-up. An automatic type of arc frame — it unfolds automatically when the tent is removed from the cover. This type of frame is often used in small budget tents, intended for those who prefer camping, nature trips and music festivals. Such tents are packed in a small round bag, which takes up a minimum of space in a car trunk or among the hand luggage of vacationers.

Both the rigidity of the frame and the reliability and durability of the tent itself depend on the thickness of the arcs. Usually, the larger and more capacious the tent, the thicker the arches are needed for the frame. Arcs made of plastic and fibreglass most often have a thickness of 7 to 13 mm, while steel and aluminium — from 5 to 16 mm. With an increase in the section of the arcs, the weight of the tent in the folded state also increases.

An indicator that reflects the ability of the tent awning to withstand moisture without getting wet. It is expressed in millimetres of water column — the height of the water column that the awning can withstand (the area of impact is out of the question, because the load per unit area under water depends only on the height of the water column and is not related to the area of \u200b\u200bits base). The significant figures indicated in the characteristics (for example, 4000 mm of water column, i.e. 4 metres) are due to the fact that raindrops can have a significant speed and, when they hit the tent, create a load at the point of impact comparable to the pressure on depth of several metres.

In general, the higher the waterproof rating, the better the awning will cope with the effects of rain and snow. Indicators up to 3000 mm w.c. Art. are considered sufficient for places where it rains rarely, awnings for 3000 – 7000 mm of water. Art. allow you not to be afraid of intense downpours, and in expeditionary (see "Destination") tents designed for extreme conditions, this figure can reach 10,000 mm of water. Art. and even more. However, more water-resistant fabrics, usually, have a significant weight, so in each individual case it makes sense to choose the option that is optimal in terms of durability and weight.

— Polyester. Synthetic material with good durability and waterproof performance. In addition, it is resistant to adverse effects (does not lose strength when wet, exposed to acidic and alkaline environments, temperature changes).

— Nylon. In general, the characteristics of nylon are somewhat lower than those of polyester: it tends to stretch when wet and is generally less resistant to adverse effects. At the same time, given that most owners use tents in relatively simple conditions, these points are not critical; in addition, some manufacturers use a special treatment to improve the durability of nylon.

— Polyethylene. This material is mainly used in inexpensive models of camping tents (see "Purpose") — this is primarily due to its significant weight. For other characteristics, it does not have key differences from other materials.

— Polyamide. The general name for a class of fabrics, which includes, in particular, nylon and nylon. Some manufacturers use this term for marketing purposes: "polyamide" sounds more solid than "nylon", although these materials practically do not differ in characteristics and are used in the same way — mainly in inexpensive models.

An indicator that reflects the degree of resistance of the bottom of the tent to moisture. For more information about the features of measuring this indicator, see "Tent waterproofness". Here also note that, for obvious reasons, the bottom, unlike an awning, is practically not subject to rain drops — as a result, the requirements for bottom water resistance are significantly lower. So, fabrics with a water resistance of 3000 mm of water. Art. are considered absolutely waterproof (up to the possibility of putting a tent in a puddle), and higher values usually indicate an increased thickness of the fabric and corresponding strength and wear resistance. Just like with an awning, more waterproof fabrics tend to have a significant amount of weight, so it doesn't always make sense to look for bottoms with maximum water resistance.

— Reflective elements. The outer surface of the tent is equipped with special reflective inserts. Thanks to this, the location of the tent will be visible from afar, which allows users to quickly navigate in the dark, easily determining the location of the tent city / tent. Often, reflective fibers are woven into wind braces so that at night they do not catch on.

— Mosquito net. Fine-mesh mesh covering the openings in the tent: entrances, windows, ventilation openings. Its presence is highly recommended if you plan to use the tent in the warm season: it allows you to ventilate the interior without letting mosquitoes and other unpleasant flying insects inside.

— Lantern loop. A special mount (loop, hook or carabiner), usually under the ceiling, designed to secure the lantern inside the tent. It will allow you to easily organize indoor lighting and eliminate the need to hold a flashlight in your hands or independently find a place for its best location.

— Internal pockets. Pockets located on the inside of the tent. They facilitate the organization of the internal space, allowing you to conveniently place relatively small items — glasses, watches, some tools, etc. It also reduces the risk of accidentally crushing fragile items.

— Shelf for small items. The purpose of t...he hanging shelf is generally similar to the inside pockets (see above): to organize the space inside the tent so that small items are not lost and are not accidentally crushed. In some tents, there may be several such shelves. Shelves are usually located in the upper part of the tent, which allows them to also be used as a stand for a lantern if there are no loops for it (see above) or it is impossible to use it for some reason.