Comparison MSR Elixir 2 vs BASK Pinnate 2

The total weight of the tent is including the frame and other accessories.

This parameter depends primarily on the purpose (see above), and after that — on seasonality, capacity, and additional functions. For example, in trekking and expedition models, the weight usually does not exceed 5 – 7.5 kg, and the lightest of these products can weigh 2 – 3 kg or even less, while being full-fledged tents for 2 people or even more. However, for a trekking tent, such a small weight with a capacity of more than 2 people usually means that this model is designed exclusively for the summer. For most camping tents, the weight starts at 6 kg, although among them there are also quite light products — by 4 – 5 kg, 3 – 4 kg, or even less (in such cases, light weight can also mean a purely summer specialization). And the most capacious and/or multifunctional models can have a weight of 10 – 15 kg, 15 – 20 kg and even more; in this weight category, you can mainly find tents, camping tents for many people and fishing tents for carp fishing (see "Destination").

When choosing a tent according to this indicator, it is worth considering that it does not always make sense to chase the maximum weight reduction. Yes, the...light tent is the most convenient to carry; on the other hand, weight reduction inevitably affects one or several other characteristics at once. So, most often, lighter models are either more expensive or smaller in size and less roomy and functional than their heavier counterparts. And sometimes weight reduction also negatively affects the security (including moisture resistance) and the overall reliability of the product. Therefore, it makes sense to specifically look for the lightest tent possible in cases where weight reduction is of key importance; a typical example is long trips, in which all the equipment has to be carried “on oneself” for a long time. And even in such cases, it is worth remembering other important characteristics. For example, for use in late autumn, when frosts are likely, it is better to choose a heavier tent with winter seasonality than a light model that is not designed for winter conditions.

The vestibule is a kind of "entrance hall" in front of the entrance to the main compartment (s) of the tent.

The specific design and purpose of such a "hallway" may be different. So, in small two-layer tents, the space between the inner and outer layers in front of the entrance plays the role of a vestibule (for this, the outer canopy is stretched at a greater angle relative to the vertical than the inner one). The dimensions of such a compartment are small, it is designed mainly for storing individual items, such as shoes. In larger models, the vestibule is made in the form of a full-fledged compartment, which differs from the main compartment only in the absence of a bottom (although there are exceptions). Such a compartment can be located between two sleeping compartments; and in some tents two vestibules are provided at once.

Anyway, such equipment increases the useful area of \u200b\u200bthe tent and provides additional comfort when using it. Tambour can be used to store equipment, often quite bulky; with an open entrance, it provides additional protection for the main volume of the tent from rain, sun and wind; and in a large vestibule(150 cm long or more), you can even organize additional sleeping places (if the weather permits) or even an auxiliary room such as a kitchen, dining room, administrative area, etc. " below.

The length of the vestibule provided in the tent.

See above for more details on the vestibule. As for its dimensions, the length of the vestibule is measured along the same side along which the length of the entire tent is measured; and the width of this compartment usually corresponds to the overall width of the tent, and it does not need to be specified separately in the specifications. At the same time, we note that due to such measurement rules, the length of the vestibule is often less than its width; this is quite normal in this case.

The specific ratio between the dimensions of this compartment in different tents may be different. However, in general, a longer vestibule is usually larger and more capacious than a shorter one. When choosing, it should be taken into account that a large and spacious additional compartment increases overall comfort, but it significantly affects the price and weight of the tent (not to mention its overall dimensions). So when choosing for this parameter, it is worth considering the real conditions and features of the operation of the tent. We only note that in order to organize additional beds, it is worth paying attention to vestibules with a length of at least 150 cm — usually, they can accommodate additional places at least across, and often along the tent.

The number of bedroom entrances provided in tent design.

It is worth clarifying that if there are several bedrooms in the structure (see "Sleeping areas"), then in this case it is not the total number of entrances that is taken into account, but the number of entrances per bedroom. For example, if the tent has 2 sleeping areas, each with 1 input, then the characteristics will indicate 1 input to the bedroom.

In other words, if the design states 2 entrances to the bedroom, this means that each bedroom has two exits (regardless of the total number of bedrooms). Such a design is convenient primarily because you can leave the sleeping slot in the most convenient way, if necessary, without disturbing your sleeping neighbors. On the other hand, a design with one input provides a higher degree of thermal and moisture insulation; such tents are better suited for particularly unfavorable conditions.

— External. The external frame is considered more convenient to set up, especially in the case of double-layer tents (see "Inner tent"), since both the inner tent and the outer awning are put on the frame at once. On the other hand, such a frame is more susceptible to the negative influence of natural conditions and does not allow the inner tent to be set up separately.

— Internal. The internal frame is somewhat more difficult to install than the external one; at the same time, it is less susceptible to the influence of unfavorable external conditions, and in double-layer tents (see "Inner tent") with an internal frame, it is usually possible to install only the inner tent, without an awning.

It should be noted that only tents in the shape of a hemisphere or half-barrel have a classic frame (see "Body shape"); in the case of gable tents, the characteristic "external/internal" refers primarily to the location of the supports, and the term "frame" is not applied at all to tent models.

— Inflatable. In such tents, the role of the frame is played by sealed hollow tubes made of flexible material (rubber or polymers), usually arched. When folded, they can be rolled up quite compactly, and when the tent is set up, they are inflated (usually with a special pump), acquiring the desired shape and sufficient rigidity to support the awning. The advantages of inflatable frames are their...light weight and ease of installation; they usually belong to quick-setup systems (see above for the latter). On the other hand, inflatable elements are very sensitive to damage: a small crack or hole, not critical for an element of a regular frame, disrupts the seal and makes the tent unusable.

— Pop-up. An automatic type of arc frame — it unfolds automatically when the tent is removed from the cover. This type of frame is often used in small budget tents, intended for those who prefer camping, nature trips and music festivals. Such tents are packed in a small round bag, which takes up a minimum of space in a car trunk or among the hand luggage of vacationers.

The arcs are connected using a connector (hub). Most often, there is only one, but there are variations when arc-stands are attached to the "main" arc. The hub structure (HUB) unites the entire tent frame into one whole, makes the tent more reliable and stable, simplifies the installation of the structure, and increases the accuracy of the geometry of the installed tent. It is impossible to put up a tent with a HUB structure crookedly, even if you deliberately try to mount the structure poorly. The main idea of hubs is to mount the arcs and guides as vertically as possible. In this case, the tent becomes extremely roomy.

The number of poles provided in the frame of the tent. For hemispherical types (see "Shape") for 2-3 people, not intended for extreme conditions, 2 poles are considered quite sufficient; larger and/or reinforced models may have more poles. In the case of half-barrels, this amount is directly related to the length of the tent.

Both the rigidity of the frame and the reliability and durability of the tent itself depend on the thickness of the arcs. Usually, the larger and more capacious the tent, the thicker the arches are needed for the frame. Arcs made of plastic and fibreglass most often have a thickness of 7 to 13 mm, while steel and aluminium — from 5 to 16 mm. With an increase in the section of the arcs, the weight of the tent in the folded state also increases.

— Nylon. Synthetic material with good water resistance and average characteristics in terms of strength and resistance to negative influences: quite main function light weather conditions, however, when wet, it loses some strength (tends to stretch), and is also sensitive to prolonged exposure to ultraviolet radiation. As a result, it is used relatively rarely.

— Polyester. It also refers to synthetic materials, it is considered a slightly more advanced option than nylon: it withstands wetting and heating well, is less sensitive to ultraviolet radiation, and as a result, it has greater durability. At the moment it is the most popular material for awnings.

— Polyamide. The general name for some varieties of synthetic fabrics, including, in particular, nylon and nylon described above. The properties of polyamides are similar to nylon: on the one hand, low cost, resistance to moisture and abrasion, as well as strength, on the other hand, a tendency to stretch when wet and loss of strength when exposed to UV radiation

— Polycotton. A material that combines cotton with synthetic fibers (usually polyester), usually in a ratio of 1:2 (synthetic-cotton). This combination provides durability, resistance to adverse conditions, polycotton resists moisture well and at the same time “breathes”. It's also better than pure synthetics at keeping you cool on a hot day and warm on a cold day. At the same time, this material is quite heavy and expensive, which is...why it is rarely used and only in camping tents (see "Purpose").

— Polyurethane. Typically, this refers to a polyurethane coating applied to a synthetic polyester or nylon backing. The main function of such a coating is to improve the water resistance of the awning (see below). However, the specific values of water resistance in different models can vary markedly. The base material (and, accordingly, the main features of the awning) usually depends on the price category of the tent.

— Polyethylene. Polyethylene is absolutely waterproof, but it also does not let air through. As a result, this material is found exclusively in tents (see "Destination").

— Texit membrane. A variety of high-quality membrane fabrics, combining, on the one hand, high water resistance values (10,000 mm Hg and above), on the other hand, the ability to "breathe" and let water vapor through, which contributes to thermoregulation and maintaining a comfortable climate in the tent. However, this material is expensive, and therefore it is used only in high-end expeditionary equipment.

— Cotton. Natural cotton, usually, with nylon or polyester rip-stop threads, as well as additional water-repellent impregnation. This material is durable, reliable and at the same time passes air well and provides convenient thermoregulation, keeping cool in hot weather and warm in cold weather. Its disadvantages are the high cost and rather large weight, which limits the use of cotton for advanced models of camping tents.