Comparison Kentavr MB-2012DE vs Temp DMK-1350

The maximum width of the strip of land processed by the machine in one pass.

The large width makes it easier to work in large open areas, allowing them to be dealt with faster. At the same time, it is easier to deal with bottlenecks and hard-to-reach nooks and crannies with a small working width — a large unit may simply not fit where a smaller one will pass without problems. So it is worth choosing according to this indicator, taking into account the features of the planned work. If we talk about specific numbers, then in the smallest models the capture width does not exceed 50 cm, in the largest it can be 1 m or more, a value from 50 to 75 cm can be called average, and from 75 cm to 1 m — above average.

Also note that some models allow you to expand the processing width by installing additional cutters. However, note that the wider the band, the more power is needed for efficient operation. It is believed that for the full use of the two-wheel tractor, it must produce at least 1 hp. for every 20 cm of width; however, for loose soils and shallow depths, smaller values are sufficient.

The maximum processing depth provided by the unit. In cultivators with non-replaceable cutters, this parameter is determined primarily by the cutter diameter, in walk-behind tractors designed for active cutters (see below) - by design features (in such models, even high power does not guarantee a large working depth). The most limited indicator in modern walk-behind tractors is up to 20 cm, and a value from 21 to 25 cm can be called small. However, often even such capabilities are quite sufficient. A depth of 26 to 30 cm already provides quite extensive capabilities, and the most advanced models are capable of "biting into the ground" more than 30 cm.

In any case, the optimal processing depth depends on the type and condition of the soil, as well as the crops for which the soil is being prepared; detailed recommendations on this matter can be found in specialized sources. So it does not always make sense to look for a model with maximum depth - especially since such capabilities require high power. It should also be noted that in many units the depth can be adjusted.

The number of cutters that the two-wheel tractor is equipped with. Note that for models with active rototillers (see below), this parameter is not indicated: such attachments are removable, and active rototillers with different performance characteristics can be installed on one unit.

Speaking of quantity, a cutter means a separate "asterisk" of several curved knives installed on the working axis of the unit. The number of such “stars” is selected depending on the processing width that the manufacturer wants to provide: one cutter captures a strip on average from 12 to 18 cm, and several of them are needed for a more or less decent working width.

The working volume of the gasoline or diesel engine of the cultivator / two-wheel tractor. For an internal combustion engine of the same type (see "Type of internal combustion engine"), power and fuel consumption usually directly depend on the volume. Also, the classification of a two-wheel tractor as a vehicle according to the traffic rules of a particular country may depend on the engine volume; you should pay attention to this if you plan to use the unit as a tractor and drive on roads.

Horsepower of two-wheel tractor/cultivator motor. The basic unit of power nowadays is watt, however for petrol and diesel engines (see "Motor type") the more traditional designation in horsepower is often used. 1 hp is approximately equal to 735 watts.

More powerful motor allows achieving higher productivity, width and depth of processing. On the other hand, high power significantly affects the price, weight and dimensions of the unit, as well as the consumption of electricity/fuel. In light of this, the engine characteristics are selected by the manufacturer taking into account what "weight category" the walk-behind tractor belongs to. The most limited modern units have a power of up to 2 hp, in the heaviest and most advanced this figure can exceed 13 hp ; 4 - 7 hp can be called an average indicator, and 2 - 4 hp and 7 - 13 hp are below and above average, respectively.

Detailed recommendations on the optimal power for a given situation can be found in specialized sources.

The power of the two-wheel tractor/cultivator engine in watts. This designation is usually used for electric engines, but can also be used for petrol/diesel engines, along with horsepower (for more information, see the "Motor power" section above).

More powerful motor allows achieving higher productivity, width and depth of processing. On the other hand, high power significantly affects the price, weight and dimensions of the unit, as well as the consumption of electricity / fuel. In light of this, the engine power is selected by the manufacturer taking into account what "weight category" the walk-behind tractor belongs to, what characteristics it should show. So, the lightest models have a power of up to 1.5 kW, this is the device that is best suited for a small area of 6 - 8 acres. Walk-behind tractors up to 3 kW can cope with 10 - 15 acres, a power of 3.5 - 5 kW is suitable for a plot of 50 acres to a couple of hectares. Units for 5 - 10 kW are already classified as professional level, they can "tame" spaces of 7 - 10 hectares; and the heaviest and most powerful modern walk-behind tractors have a power of more than 10 kW.

The volume of the fuel tank of the cultivator / two-wheel tractor; knowing this parameter and fuel consumption (see above), it is possible to determine the maximum operating time of the unit on a single refill. If you plan to use the device in large areas or to work for a long time, it makes sense to look for a model with a large tank — it will not have to be filled often. On the other hand, for short-term work in small areas, a large tank is not required — in this case, it only increases the weight and dimensions of the unit.

The method of starting a petrol or diesel engine (see "Motor type") provided in the unit.

— Manual. Starting by human muscle power: the operator pulls a special cable or turns a handle, which causes the shaft to rotate and the engine to receive the initial impulse necessary for operation. Manual starting systems are inexpensive, lightweight and compact, and do not depend on batteries that can run out at the most inopportune moment. On the other hand, the starting process itself may require significant effort, especially in a heavy, powerful engine. Therefore, this option is used mainly in relatively low-power models.

— Electric . Starting with starter — small electric motor powered by a battery. Such systems are much more convenient than manual ones — the operator is actually required to press a button or turn a key; they are suitable even for the most powerful motors. On the other hand, a starter with a battery significantly increases the weight, dimensions and cost of the entire unit, and if left idle for a long time, the battery may run down, and the system will become useless (however, a spare manual "starter" may be provided for this case). Therefore, this starting method is used exclusively in heavy equipment, for which the ability to do without manual starting is more important than the described disadvantages.

The diameter of the main wheels of the two-wheel tractor / cultivator. For flat areas, a small diameter is enough, and for difficult terrain, large wheels are better suited — they are much easier to cope with pits, bumps and various obstacles.