Comparison Blaupunkt GTA-250 vs Blaupunkt GTA-270

Rated power output by the amplifier per channel when a load (speakers) is connected to it with a nominal impedance of 2 ohms. For details, see "Nom. channel power (at 1 Ohm)”.

Rated power output by the amplifier per channel when a load (speakers) with a nominal impedance of 4 ohms is connected to it. For details, see "Nom. channel power (at 1 Ohm)”.

Rated power delivered by the amplifier to a load connected in a bridge circuit. For more information about the rated power, see "Nom. channel power (at 1 Ohm)”.

With a bridged connection, the speaker is connected not to one channel, but to two at the same time — the “positive” connector of one channel and the “negative” connector of the other are used. If the amplifier has a similar format of operation, then such a pair of channels operates in antiphase, due to which the power is summed up. This allows you to connect speakers to the amplifier, the power of which is twice the nominal power of the device: for example, at 150 watts per channel, 300 watts of acoustics can be bridged. If there are 4 or more channels, it becomes possible to use several speakers according to the "bridge" scheme. This is usually directly indicated in the specifications — for example, the entry "2x300 W" in the "Bridge connection" item means the ability to work with two speakers, each with 300 W.

The requirements for load resistance when connecting with a bridge are the same as for conventional; see "Maximum Resistance" for details.

The ability to change the characteristics of the output signal of the amplifier in such a way as to adapt them to speakers with different nominal impedance. Impedance (impedance) is one of the most important characteristics that determine the compatibility of acoustics and amplifier; for more on it, see "Maximum Impedance". Also note here that such tuning greatly expands the possibilities for choosing acoustic systems, since it removes strict requirements for impedance (although it does not necessarily give complete freedom; see more details there). However, the output power rating for different impedances will vary; usually this is written in the characteristics in the form of specific values for each option provided for in the design.

— DSP processor. The digital audio processing processor improves the overall sound quality and provides additional options for its adjustment. One of the most important functions of DSP is time correction: it allows you to adjust the operation of acoustics so that sound from speakers located at different distances from the customer reaches him at the same time. This coordination significantly improves the sound experience.

The presence of a processor significantly affects the price of the amplifier, but in most cases it is a justifiable price to board for the sound quality. But the clear disadvantage of “processor” models is the complexity of installation and configuration; for this it is best to contact a specialist.

— Phase adjustment. The ability to shift signals entering different channels of the amplifier in phase relative to each other; The phase shift in this case is a small, fraction of a second, delay of the signal on one of the channels relative to the other. The need for such a setting is due to the fact that the speakers on different channels (including the subwoofer) may be at different distances from the listener; Because of this, as well as due to the peculiarities of signal processing, the sound from them may arrive with some desynchronization. By adjusting the phases, you can eliminate this phenomenon and achieve the highest quality sound.

— High voltage in...put. This input is useful if the radio does not have a special connector (line output) for the amplifier - it allows you to use the signal going to the speakers when connecting. Such a signal is much more powerful than at the linear output, and outputting it to the standard linear input of the amplifier can damage the device; the high-voltage input will cope with the task without any problems. It must be borne in mind, however, that the high-voltage connection is more of a backup option than a full replacement for the linear input. The fact is that before entering the external amplifier, the signal passes through the radio's own amplifier, which introduces additional distortion.

— Bass Boost function. As the name suggests, this feature is designed to enhance the sound at low frequencies, resulting in a more powerful and rich bass sound. It will be especially useful if the amplifier is planned to be used with a subwoofer. The simplest options involve enhancing the bass without adjustments; more advanced models allow you to adjust the frequency range and degree of gain.

— Infra-low-pass filter (FINCH). This function is relevant primarily when connecting an amplifier to a subwoofer; it allows you to minimize reproduced infrasound - vibrations whose frequency is below the human hearing threshold. There are several purposes for this adjustment. Firstly, high-power infrasound can cause poor health and even health problems. Secondly, some of the power will be spent on its reproduction, which will negatively affect the audible sound. Thirdly, ultra-low frequencies greatly wear out the cone and can even damage the speaker. In some amplifiers, the FINCH has frequency adjustment.

— Low pass filter (LPF). Thanks to this function, the customer can separately change the volume of the bass sound, adjusting the sound to his own preferences and features of the environment. It will be especially useful if the amplifier is used for both the main acoustics and the subwoofer - the low-pass filter will actually work as a volume control for the latter.

— High-pass filter (HPF). The high-pass filter is used to fine-tune the sound - it allows you to separately adjust the volume of high frequencies without affecting the rest, and thus change their share in the overall sound picture.