—
Protection against moisture. The presence of protection in the design of the machine, which prevents moisture from entering the sensitive elements of the structure and the corresponding unpleasant consequences (short circuits, corrosion, water hammer, etc.). This feature is practically mandatory for outdoor models, especially off-road types with internal combustion engines (see above). However, the specific degree of such protection differs significantly in different cases: one model can be designed, for example, for a maximum of splashes from wet asphalt or light rain, while the other will calmly survive driving through a puddle “hood-deep”. Therefore, this point should be clarified according to the official data of the manufacturer.
—
Protection against dirt. Protection to prevent dust and dirt from entering parts that require cleanliness. Similar in many respects to the water protection described above — in particular, it is very important for outdoor use and can vary significantly from model to model.
—
Centre differential. The presence in the design of the machine of a differential located between the front and rear pair of wheels and distributing torque from the engine between the front and rear axles. By definition, it is found only in models with all-wheel drive (see above). The main function of this mechanism is similar to cross-axle differe
...ntials — it allows the wheels, in this case the front and rear, to rotate at different speeds so that the chassis and tyres do not experience increased loads. A similar need arises, in particular, when cornering at low speed. In addition, the centre differential improves patency: when one of the pairs of wheels slips, it distributes the torque so that most of it falls on the wheels that retain traction.
— Metal main pair. The main pair is called two gears responsible for transmitting torque from the engine to the transmission: one of them is located on the engine shaft, the second — on the transmission shaft. This is one of the most important structural elements of the machine, which is subjected to significant loads during use. The main pairs made of metal are much stronger and more reliable than plastic ones; if you are purchasing a model for riding in difficult conditions (for example, a short course or tricks, see "Purpose (class)"), the presence of such equipment will be very desirable. At the same time, for entertainment purposes, it is rather an excess — after all, metal gears are more expensive than plastic ones.
— Anti-roll bars. The presence in the design of the machine of special devices that prevent the tipping of the structure to one side, in particular during sharp turns: during cornering, the stabilizer distributes the load on the wheels in such a way as to reduce chassis roll. However, this is not the only purpose of these parts — stabilizers of different stiffness are also a tool for distributing the grip balance between the front and rear axles. For example, if the front stabilizer is softer than the rear, the grip of the front axle will be higher, which ensures good steering, but reduces the sensitivity of the control; with a softer rear stabilizer — on the contrary. These points are described in more detail in special sources. It is worth noting that stabilizers are not a 100% guarantee against a coup — however, the likelihood of such an event is significantly reduced if they are present.
— Metal deck chassis. The deck is the basis of the chassis of the machine, the frame on which the engine, transmission and body are placed. The high strength of the deck is important for models that are subjected to significant stress during riding, for example, when used for short corsets (see "Purpose (class)"). Aluminium alloys are often used as a material for metal decks in modern cars — they combine good strength and low weight. However such materials also affect the cost of the model, respectively.
— Opening doors. Opening doors enhance the similarity of radio-controlled cars with real cars. You can put a toy driver behind the wheel of such cars in miniature, and passengers in the passenger compartment. Also, through the doors, access to the interior of the radio-controlled car is provided.
— Light effects. The presence of various lighting effects in the model: headlights, parking lights, flashing beacons (flashing lights), bottom lighting, etc. Such equipment not only makes the machine look like a real car, but also makes it more noticeable to others and reduces the likelihood of unpleasant incidents. At the same time, for advanced models, these moments do not play a key role, so lighting effects are found mainly in inexpensive entertainment cars.
— Sound effects. The presence in the model of various sound effects — for example, a horn, a siren, the sound of a powerful engine, etc.; sometimes there are even built-in melodies. To play sounds, usually, a small speaker is provided. This function is purely for entertainment purposes and is found only in simple and inexpensive models designed for the younger age group.
— Driver. A toy pilot seated behind the wheel of a radio-controlled car. The presence of a pilot allows you to give free rein to your imagination - driving a car from a distance, you can imagine that it is being driven by a little man.The material from which the body of the machine is made. The body in this case means the upper part of the model, mounted on the deck of the chassis and giving it a resemblance to a real car by imitating the shape and coloring of the body.
One of the most popular body materials is plastic. It is inexpensive, easy to process, can be produced in any shape and colour, and applying even a complex pattern to plastic is not a problem. At the same time, the strength of this material is sometimes insufficient for models designed for difficult driving conditions. Therefore, plastic can be supplemented with metal elements — usually made of aluminium alloy, which combines good strength and low weight. However these machines are more expensive.
