Comparison Genius SW-G2.1 300 vs Genius SW-2.1 300

Sensitivity characterizes the loudness of the speakers when a signal of a certain power is applied to them. The higher this indicator, the higher the volume will be with the same characteristics of the signal source; simply put, on the same computer and the same volume settings, more sensitive speakers will play louder.

In general, an indicator of 85 dB is considered good, 90 dB and above is excellent. On the other hand, computer speakers rarely need a very high volume — they are usually located close to the user and are designed only for him. So in general, this parameter can be ignored.

The ratio of the level of the useful signal (actually reproduced sound) to the level of extraneous noise provided by the speaker amplifier in normal mode.

Any amplifier inevitably creates its own noise; You can't get rid of them, but you can reduce their level. The higher the signal-to-noise ratio, the clearer the sound will be, the less noticeable extraneous interference will be. In modern computer speakers, this figure can vary from 52 – 55 dB (the minimum figure so that the noise does not cause much discomfort) to 90 – 95 dB (comparable to fairly advanced Hi-Fi equipment). However, note that the signal-to-noise ratio is far from the only parameter that affects the sound quality, and its high value does not guarantee a pleasant sound from the speakers.

The range of audio frequencies supported by acoustics. The wider this range — the fuller the reproduced sound, the lower the likelihood that some of these details at low or high frequencies will remain “behind the scenes”. At the same time, the human ear is able to hear frequencies of the order of 16 – 22,000 Hz, and with age, this range narrows even more. In modern audio equipment, especially at the top level, there may be more extensive ranges, but from a practical point of view, this does not make much sense. In addition, it is worth noting that a wide frequency range in itself does not guarantee high-quality sound — a lot also depends on the frequency response.

The power rating of each individual front speaker provided in the speaker system. This parameter can be specified for a system with any number of speakers (see above) — all sound formats used in computer acoustics provide a pair of front speakers.

In the most general terms, the higher the power, the louder the speaker is capable of sounding. For more information about this parameter, see "Total power" above. Also note here that for stereo systems without a subwoofer, the power of one front channel is half of the total power; in more advanced acoustics, the power ratio between the channels may be different.

Rated power of the complete subwoofer of the acoustic system.

Recall that a subwoofer is a specialized speaker for low and ultra-low frequencies; such a speaker is especially useful for games and movies, it is for such content that well-defined bass is most important. Accordingly, the saturation and (to a certain extent) the overall sound quality of low frequencies depends on the power of such a speaker. "Subs" are usually matched to the power of the rest of the system components, however, sets with a similar total power of the main channels may still differ in the characteristics of the subwoofers.

It is also worth noting that the power of this component can be a very significant part of the total power of all acoustics: in some models, about half of the “total watts” (or even more) falls on the subwoofer. This should be taken into account when comparing; see "Total power" for more details.

The presence of detachable cables will save you from possible damage to the device associated with bending the wires. If such an incident occurs, an easy replacement of the wire with a new one allows you to continue using the speakers, and not carry them to a service centre. However, this solution is mainly used in higher-level models, which affects the cost. At the same time, not only audio cables can be removable, for which connectors are provided (according to the classics, this is RCA), but also the power cable.

The material used for the woofer enclosure — subwoofer (of course, if there is one in the kit).

The most popular material options for such finishes today are plastic and MDF(medium density fibreboard). Plastic is often considered a more budgetary material, MDF is more advanced and acoustically of high quality. However, in fact, this difference is not critical, and the sound quality is more related to the price category of the acoustic set than to the material of the subwoofer. But what the finishing material affects unambiguously is the appearance.