Comparison Sony KD-43X75WL 43 " vs Sony KD-43X80L 43 "

— Edge LED — side backlight of the matrix. In this case, the LEDs are distributed around the perimeter of the screen. To evenly distribute the backlight, the background of the matrix has a special reflector. An important advantage of TVs with Edge LED backlighting is the minimum thickness of the device. Among the shortcomings, one can note the presence of glare at the edges, which appear under certain conditions. Glare may be visible in scenes where dark hues predominate.

— Direct LED — rear matrix backlight. In this case, the LEDs are evenly distributed over the entire screen area. The Direct LED backlight makes the image contrast and bright at the same time. TVs with this technology have good colour reproduction. Among the shortcomings can be noted increased power consumption and increased dimensions. Additionally, such TVs have a large delay (Input lag), which is why Direct LED backlit screens are poorly suited for dynamic games.

— FALD (Full-Array Local Dimming) is a backlight technology widely used in LG TVs. A close analogue of FALD is the Direct LED backlight. The LEDs are also evenly spaced across the entire surface of the matrix, but FALD technology provides a bright, colour-rich image with high contrast. Another distinctive feature of FALD is the ability to reproduce natural blacks. When black is displayed on the screen, the LEDs are turn...ed off in groups, by sector, which allows to make black extremely saturated. Of course, the abundance of LEDs on the matrix makes the TV more massive, and at the same time heavy. The appetite for electricity in such models is above average.

— Mini LED. Screen backlight system on a substrate of reduced LEDs (hence the Mini prefix). On the same plane of the TV panel, the number of LEDs has increased several times, if we draw parallels with traditional LED systems. As a result, the canvas with Mini LED backlight has many times more local dimming zones of the picture (Local Dimming), which is necessary for the correct operation of the extended dynamic range image technology. For playing HDR content, Mini LED systems are much better than ordinary LCDs.

— Dual LED. Proprietary backlight system used in Samsung TVs. The technology involves illuminating the image on the screen with two types of LEDs: one emits light in a cold spectrum, the other in a warm one. The Dual LED enhances colour reproduction and enhances detail contrast by adapting the colour tone of the picture according to the content on the screen.

The highest frame rate supported by the TV.

Note that in this case we are talking specifically about the screen’s own frame rate, without additional image processing (see “Index of dynamic scenes”). This frequency must be no lower than the frame rate in the video being played - otherwise there may be jerks, interference and other unpleasant phenomena that degrade the quality of the picture. In addition, the higher the frame rate, the smoother and smoother the movement in the frame will look, and the better the detail of moving objects will be. However, it is worth noting here that playback speed is often limited by the properties of the content, and not by the characteristics of the screen. For example, films are often recorded at a frequency of only 30 fps, or even 24 - 25 fps, while most modern TVs support frequencies of 50 or 60 Hz. This is enough even for viewing high-quality content in HD resolutions (speeds above 60 fps in such video are extremely rare), but there are also “faster” screens on the market: 100 Hz, 120 Hz and 144 Hz. Such speeds, as a rule, indicate a fairly high class of the screen; they also often imply the use of various technologies designed to improve the quality of dynamic scenes.

Dynamic Scene Index (DSI) provided by the TV screen.

DSI is a rather specific parameter that can be called "visible framerate". Its appearance is due to the fact that a high frame rate is highly desirable for dynamic scenes — it provides smooth images and good detail of moving objects. However, for technical reasons, it is not possible to achieve indicators above 200 Hz in most screens. In order to remedy the situation, manufacturers use special technologies that create the effect of increasing the frame rate.

Such technologies may have different names, but they have the same principle of operation — inserting additional frames between the "own" frames of the video being played. And the dynamic scene index describes the overall effectiveness of such technology used in a TV. For example, a DSI of 200 Hz means that the image quality on the screen approximates a frame rate of 200 Hz, although the actual frame rate is often as low as 50-60 Hz.

In the most advanced models, the dynamic scene index can be up to 3000 Hz, and options above 3000 Hz are considered to be TVs with a high dynamic scene index. However, it is worth noting that such specifications are more of an advertising ploy than a real advantage: in fact, the threshold for human perception is 400 – 500 Hz, a further increase in the DSI does not give a clearly visible improvement in the image.

TV support for high dynamic range technology — HDR.

This technology is designed to expand the range of brightness reproduced by the TV; Simply put, an HDR model will display brighter whites and darker blacks than a regular TV. In fact, this means a significant improvement in colour quality. On the one hand, HDR provides a very "live" image, close to what the human eye sees, with an abundance of shades and tones that a normal screen cannot convey; on the other hand, this technology allows to achieve very bright and rich colours.

However for the full use of this feature, you need not only an HDR TV, but also content (movies, TV broadcasts, etc.) that was originally created for HDR. Also note that there are several different HDR technologies that are not compatible with each other. Therefore, when buying a TV with this feature, it is highly advisable to clarify which version of HDR it supports (HDR10, HDR10 + or Dolby Vision). And the following are found:

— HDR10. Historically the first of the consumer HDR formats, less advanced than the options described below but extremely widespread. In particular, HDR10 is supported by almost all streaming services that provide HDR content, and it is also common for Blu-ray discs. Allows to work with a colour depth of 10 bits (hence the name). At the same time, devices of this format are also compatible wi...th content in HDR10+, although its quality will be limited by the capabilities of the original HDR10.

— HDR10+. An improved version of HDR10. With the same colour depth (10 bits), it uses the so-called dynamic metadata, which allows transmitting information about the colour depth not only for groups of several frames, but also for individual frames. This results in an additional improvement in colour reproduction.

– Dolby Vision. An advanced standard used particularly in professional cinematography. Allows to achieve a colour depth of 12 bits, uses the dynamic metadata described above, and also makes it possible to transmit two image options at once in one video stream — HDR and standard (SDR). At the same time, Dolby Vision is based on the same technology as HDR10, so in modern video technology this format is usually combined with HDR10 or HDR10+.

TV support for one or another brightness / contrast enhancement technology.

Usually, in this case, software image processing is implied, in such a way as to improve brightness and/or contrast (if necessary). Specific processing methods may be different — in particular, in some cases we are actually talking about turning standard content into HDR (see above), and some manufacturers do not specify technical details at all. The effectiveness of different technologies can also be different, and besides, it is highly dependent on the specific content: in some cases, the improvement will be obvious, in others it may be almost imperceptible. Also note that this feature is not always useful, so in most models it is turned off.

Types of digital tuners (receivers) provided for in the design of the TV.

Such tuners are necessary for receiving digital TV broadcasts; for normal operation, the broadcast standard must match the type of tuner (with some exceptions, see below). Note that the receivers are also available as separate devices; however, it is easier (and often cheaper) to buy a TV with a built-in tuner of the desired format. In modern TV you can find terrestrial tuners DVB-T2, cable DVB-C and satellite DVB-S and DVB-S2, here are their main features:

— DVB-T2 (terrestrial). The main modern standard for digital broadcasting. Such broadcasting has a number of advantages over traditional analogue broadcasting: it allows higher resolution and multi-channel audio transmission, with better sound and picture quality, and this quality is fully preserved until the signal weakens to a critical level. However, in some countries digital terrestrial broadcasting is just being put into operation, so it will not hurt to check the availability of DVB-T2 coverage in your area.

— DVB-C (cable). The main modern standard for digital broadcasting in cable networks. Despite the advent of the more advanced DVB-C2, it still continues to be widely used, and most likely this situation will not change for a long time.

— DVB-S (satellite). The first...generation of the digital DVB standard for satellite broadcasting. Nowadays, it is relatively rare due to the advent of a more advanced DVB-S2, which is also backwards compatible with the original DVB-S.

— DVB-S2 (satellite). The most advanced and popular of today's digital satellite broadcasting standards. Being the heir to DVB-S, has retained compatibility with it; therefore, manufacturers often limit themselves to installing only a DVB-S2 tuner on their TVs — it allows you to receive both major satellite broadcast formats.

About the interface itself, see above, and its different versions differ in maximum resolution and other features. Here are the options found in modern TVs:

— v 1.4. The oldest of the current versions, released in 2009. However, it supports 3D video, capable of working with resolutions up to 4096x2160 at 24 fps, and in Full HD resolution, the frame rate can reach 120 fps. In addition to the original v.1.4, there are also improved modifications — v.1.4a and v.1.4b; they are similar in terms of basic features, in both cases the improvements affected mainly work with 3D content.

– v 2.0. Significant update to HDMI introduced in 2013. In this version, the maximum frame rate in 4K has increased to 60 fps, and the audio bandwidth has increased to 32 channels and 4 separate streams simultaneously. Also from the innovations, we can mention support for the ultra-wide format 21:9. In the v.2.0a update HDR support was added to the interface capabilities, in v.2.0b this feature was improved and expanded.

— v 2.1. Despite the similarity in name to v.2.0, this version, released in 2017, was a very large-scale update. In particular, it added support for 8K and even 10K at speeds up to 120 fps, as well as even more expanded features for working with HDR. Under this version, its own cable was released — HDMI Ultra High Speed, all HDMI 2.1 features are available only when using cables of this standard, although basic functio...ns can be used with simpler cords.

— VRR. VRR (Variable Refresh Rate) adaptive frame rate synchronization technology allows you to adjust the refresh rate of the image on the TV screen in real time in accordance with the frame rate output by the game console or connected computer. The function ensures smooth rendering of dynamic scenes, eliminates frame breaks, and guarantees comfortable and stable gameplay. Realizable technology with standard HDMI v 2.1.

— ALLM. Automatic low latency mode for games (Auto Low Latency Mode). The TV switches to game mode when it detects a game console connection. Reducing the output delay on the TV panel screen is provided by suspending part of the image processing functions. The ALLM mode can also be useful for karaoke and video calls.

eARC. HDMI v 2.1 has an enhanced eARC (enhanced Audio Return Channel). The technology allows you to send higher quality audio from your TV to your soundbar or AV receiver. It claims to support the latest high bit rate audio formats up to 192 kHz, uncompressed 5.1 and 7.1, and 32-channel uncompressed audio. eARC also supports Dolby TrueHD, DTS-HD Master Audio, DTS:X, Dolby Atmos.

— CEC. The CEC (Consumer Electronics Control) system is designed for remote control of equipment connected to the TV using a single remote control. The devices are connected to the TV panel using an HDMI cable.

— Coaxial (S/P-DIF). An interface for transmitting audio in digital format, which allows to transmit multi-channel audio via a single cable with an RCA connector (“tulip”). In terms of resistance to interference, this standard is somewhat inferior to the optical one (see below) — this is due to the fundamental differences between these interfaces. On the other hand, electrical cable is more reliable than optical fibre and is not as sensitive to pressure and bending.

— Optical. An output for transmission of a digital audio signal on a fibre optic cable; allows the transmission of multi-channel audio. Notable for its complete insensitivity to electromagnetic interference. On the other hand, fibre optic cable is quite fragile, it must be protected from bending and strong pressure.

— Mini-Jack (3.5 mm) for headphones. Standard 3.5mm headphone jack. Headphones can come in handy if you need to keep quiet and you can’t use the TV speakers – for example, at a later time of the day; or vice versa, if the environment is noisy and the sound of the TV is hard to hear. Most modern "ears" use a mini-Jack plug, so this connector is the standard headphone output in TVs. And in some models, this output can also be used as a linear output — for example, to connect individual speakers, a sound recording device, etc.

— Subwoofer. A separate output for connectin...g a subwoofer to a TV is a speaker for reproducing low and ultra-low frequencies. Audio systems without subwoofers usually reproduce these frequencies quite poorly. The use of subwoofer allows you to achieve the most deep and rich sound, which is especially important when watching movies with a lot of special effects or high-quality recordings from concerts. At the same time, it is worth noting that such outputs are quite rare in TVs: it is assumed that a full-format external audio system is more suitable for a demanding listener than a separate subwoofer.

— Line. Standard analogue audio interface; usually, provides the transmission of two-channel stereo. It is used primarily to connect active speakers and other audio equipment (for example, audio receivers or power amplifiers) to TVs. It can use different types of connectors, but most often it provides either a 3.5 mm mini-Jack or a pair of RCA jacks for tulip cables. Note that it is a separate line output that is meant here; in some models, this function can be performed by a 3.5 mm headphone jack (see above), but for them the presence of a line-out is not indicated.