Comparison TechniSat DigitRadio BT 1 vs Camry CR 1179

— FM. The most popular broadcasting range among radio listeners today is primarily due to the fact that the vast majority of music stations broadcast in it. This is due to its features: FM uses frequency modulation, which makes it possible to broadcast sound with a fairly high sound quality, and even in stereo format. In the frequency band, the term "FM" usually refers to the 87.5 MHz to 108 MHz portion of the VHF band, although the range of individual receivers may vary. The disadvantage of FM is the limited range — within the line of sight (up to several tens of kilometers), which has secured the reputation of "urban" stations for FM stations.

— AM. Formally, this designation is not a range, but a type of modulation: "amplitude modulation" — amplitude modulation. In consumer radios, AM most often means the medium wave range of about 520-1610 kHz. Such waves have a propagation range of hundreds of kilometers, but the sound quality in this case is somewhat worse than that of FM, and therefore the AM band is mainly used by radio stations of the “conversational” genre (for example, news or journalistic).

— SW. Broadcasting on short waves (short wave) in the general range from 2.5 MHz to 26.1 MHz, divided into a number of separate sub-bands. Sound quality is average. Short waves are able to reach the opposite side of the Earth, but immediately outside the line of sight of the transmitter, a “dead zone” is formed, several...tens of kilometers wide. As a consequence, SW is commonly used for overseas broadcasts.

— DAB. Abbreviation for Digital Audio Broadcasting, i.e. "digital broadcasting". This term describes the key difference between this range and those described above: broadcasting in it is carried out not in analogue, but in digital format, the MP2 codec is used for transmission. This gives a number of advantages over traditional transmitters — in particular, a greater range with less power and high quality of the broadcast sound. In addition, this sound is practically not subject to distortion: weak interference does not affect its quality, and when the transmitter power is critically reduced, the signal is not distorted, but disappears entirely. The latter, however, can be written down as disadvantages; but the really significant drawback of this option is perhaps its low prevalence (so far) in the CIS countries. Technically, such broadcasting can be carried out in any band above 30 MHz, but in fact several options are used (depending on the country) related to the VHF band.

— DAB+. An updated and improved version of the DAB standard described above. It has all the characteristic features of digital broadcasting, and differs from its predecessor in higher sound quality at the same bit rates — both due to the use of a different codec (HE-AAC v2), and due to the use of more advanced noise correction algorithms. DAB+ broadcasts cannot be received on DAB receivers: at best, this will require a firmware update, and at worst, you will have to change the receiver itself.

Number of stations, i.e. certain fixed frequencies, which can be stored in the receiver's memory. This greatly simplifies tuning: by fine tuning the frequency once, in the future you can turn on the desired station by simply selecting it from the list (and in some models, it is enough to press a separate button once). The memory is usually found in receivers with a digital tuner (see "Tuner type").

The Radio Data System RDS technology is used primarily in the FM band; it allows, in addition to the sound signal, to transmit additional textual information by radio — for example, the names of broadcast compositions, announcements, advertising messages, etc. Accordingly, to display this information, the radio receiver must be equipped with a display.

— USB port. The presence of a USB connector allows you to connect a USB flash drive, mobile phones, MP3 players and other similar peripherals. Accordingly, such models have a built-in player and allow you to use connected gadgets exclusively as a drive.

— Card Reader. Like the USB described above, this item implies the presence of a built-in player. And the card reader also allows you to use memory cards as a drive on which songs will be recorded.

— Line input. Analogue audio input. Through such an input, you can connect an external signal source to the radio receiver — for example, an MP3 player — and listen to music through the receiver's speakers. Despite the development of digital standards, line-in is still one of the most popular connection interfaces.

The maximum power output of the receiver speaker(s) in normal operation, without overload. The higher the rated power, the higher the sound volume, but louder devices and energy require more.

A connector for connecting headphones in radio receivers, most often a standard 3.5 mm mini-jack. Headphones can come in handy when the sound from the main speaker might disturb others, or in noisy environments where an external speaker doesn't do well.

The format in which the time is displayed on the clock face.

— 12 hours. A format that enumerates individual hours (time intervals) from 1 to 12. Since there are 24 hours in a day, this numbering covers only half of the day. This option is traditional for hand dials (see "Dial type") — historically, the full circle of the hour hand corresponds exactly to 12 o'clock, and it is from this principle that both watchmakers and watch users around the world today proceed. However, it can also be found in other types of dials. Theoretically, this option may require clarification — roughly speaking, "7 o'clock — in the morning or in the evening?" — however, in the vast majority of cases, the answer to such a question is clear immediately, from the context of the situation. But when using an alarm clock (see "Functions / Capabilities") in such a watch, you have to be especially careful: if, for example, at 6 pm you set the signal time to 8 am, the alarm clock will go off at 8 pm, because the clock itself "does not distinguish" between morning and evening.

— 24 hour. A full 24-hour format, provides numbering of hours from 1 to 24 (more precisely, from 0 to 23, because exactly 24 hours are considered zero of the next day). Thus, when looking at the clock, in principle, there is no question whether we are talking about the time of "morning" or "evening": for example, 7.00 will unambiguously correspond to morning, and "7 pm" will be designated as 19.00. At th...e same time, we note that such clarification can be provided in other ways — namely, the 12-hour scale, which has additional indicators AM (ante meridiem, "before noon") and PM (post meridiem, "after noon"). Therefore, models with such modified 12-hour scales are also classified as 24-hour models in our catalog. This format is used in all types of dials, except for arrows.

— 12/24 hour. This category includes watches that have the ability to switch between a full 24-hour clock and a 12-hour clock with "AM/PM" qualifiers. Formally, both of these types of scales are 24-hour scales (and are described in detail in the relevant paragraph above); the same designation is used to emphasize the possibility of switching formats.

Among the functions in the table clock and radio you can find: alarm clock, snooze, voice notification, calendar, thermometer, world time, radio auto-off timer, time projection, dial backlight, case backlight, USB charging port, wireless charging gadgets, flashlight. More details about them:

- Alarm. The watch has a classic alarm clock that provides a sound signal at a customer-specified time. Of course, this function can be used not only for morning wake-up, but also for other warnings. However, the most popular way to use an alarm clock is to wake you up in the morning. In light of this, some models may provide a very specific way of disabling the alarm - for example, by installing a propeller in place that takes off from the clock when the alarm goes off; and some models begin to move at the same time as the signal, and you have to catch them. There can be many similar options, but they all follow the same principle: to push the customer to take active action and reduce the likelihood of falling asleep after the sound has been...turned off. Watches with original alarm clocks will be especially useful for tech who tend to wake up when they wake up, turning off the alarm and falling asleep again.

— Delay of the alarm signal (Snooze). As the name suggests, this function is designed to reschedule the alarm to a later time. Its meaning is that when a signal is triggered, the customer can literally move the alarm time by several minutes with just one click of a button. Snooze is intended primarily for tech who prefer to lie in bed for a while after the alarm goes off before getting up: it minimizes the risk of falling back to sleep and missing the time to wake up, while pressing the Snooze button is much easier than changing alarm clock manually. In some models, the delay time is fixed (usually about 5 - 10 minutes), in others it can be adjusted at will.

— Voice notification. The watch has a voice warning system. One of the most popular uses of such a system is to announce the current time at the press of a button; in some situations, this method of finding out the time can be more convenient than trying to look at the dial. Theoretically, other types of alerts could be provided - for example, a low battery warning; however, for a number of reasons they are rarely used.

- Calendar. The watch has a calendar function. This feature requires, at a minimum, the display of the current day of the month, but the matter is not limited to this: even in watches with pointer dials (see “Movement type”), the calendar can also cover the day of the week or even the current month, and in digital devices - also the year, the number of the week in the year and a lot of other information, including displaying calendar tables for each individual month. The calendar can also provide other functions, such as setting an alarm for certain days of the week.

- Thermometer. The presence of a thermometer function in the watch allows you to use it to determine the air temperature in the number. This function may be useful in cases where you need to maintain a certain microclimate - for example, if there is a baby in the house. Built-in thermometers, as a rule, are made electronic, which provides more than sufficient accuracy for domestic use. And in some models, the digital temperature display can be supplemented with a color one - for example, by changing the color of the housing backlight (see below for the backlight itself).

- World time. The presence of a world time function in the watch allows you to determine the current time in other regions. Most often, an additional dial is used for this, which is set in advance for the time of the time zone of interest and constantly displays this time; and in the most advanced models there may be several such dials. There are other ways to implement this function - for example, models with LCD screens (see “Dial type”) can provide quick switching between local time and a specified time zone. In any case, watches with a world time function are useful in cases where you regularly communicate with people from other time zones - in particular, they minimize the risk of being in an inconvenient situation by calling your interlocutor in the middle of the night or at another inopportune moment. On the other hand, today there are more practical ways to monitor standard time than desk clocks (for example, smartphones are equipped with similar tools); therefore, this function is rarely found, mainly in luxury models.

— Radio auto-off timer. A timer that turns off the receiver after a specified time. This way, you don't have to worry about turning off the device manually - just set the desired time and the receiver will turn off automatically. This can be useful, for example, if you like to fall asleep to music: by setting a timer, you can calmly fall asleep without worrying about wasting energy on “all-night” broadcasting (which is especially critical for self-powered devices, see “Power”).

— Time projection. The watch has a projector function. Thanks to it, the device is able to display various data not only on the dial, but also on various surfaces - for example, projecting information onto the ceiling or wall. In some cases, the projector mark is more convenient and better visible than the main dial. As the name of this feature suggests, the projector is primarily designed to display the time; technically, nothing prevents other data from being displayed in this way, however, for a number of reasons, such a possibility is rarely provided. As a rule, the projector unit is made rotating, which allows you to adjust it to different environments.

— Dial backlight. The watch has a dial illumination system. This backlight is convenient in low light conditions: it allows you to see the dial without using additional lighting sources (in other words, you can look at the watch even in complete darkness). Note that in this case we are talking about systems that turn on for a short time - usually for a few seconds while the customer holds the button; Constantly glowing symbols on the dial do not count as backlighting, although they can also be seen in the dark without any problems. And in some models, the dial illumination can be combined with the case illumination (see below).

— Case lighting. The watch has a case lighting system. Unlike the dial backlight described above, this function is usually not associated with the main functionality of the watch - it plays a decorative role and also allows the device to be used as a night light.

- Flashlight. The built-in flashlight allows you to use the receiver as a light source. Moreover, the power of such sources can be quite high, providing an effective range of several tens of meters. Usually this function involves a directional beam, but there are also diffused light flashlights.

— USB port for charging. The presence of a port for connecting a third-party gadget and replenishing its energy. Naturally, this solution is applicable when connecting a table clock to a 230 V power supply, and the speed itself will be mediocre.

- Wireless charger. Ability to work in Power Bank mode without using a cable. The gadget is charged wirelessly by placing the desired device on the charging area.

— Pencil stand. The presence of a pencil stand in the watch design. By design, such a stand usually represents a characteristic “glass”; its shape can be varied, but the dimensions are usually large enough to accommodate several fairly large stationery items. Therefore, despite the name, the stand can be used not only for pencils, but also for other items - pens, markers, scissors, etc.

The type of connector used to charge the built-in battery, or more precisely, to connect an external charger. The role of such a device can be played by a network or car adapter, a power bank, or even a USB port of a PC or laptop (if the appropriate cable is available).

- microUSB. A smaller version of the USB connector designed for portable devices. It appeared quite a long time ago, but does not lose popularity in our time, it is used by the vast majority of manufacturers.

- USB C. A miniature USB connector, positioned, among other things, as a potential successor to microUSB. Unlike its predecessor, it has a double-sided design, thanks to which the plug can be inserted into the socket on either side. It is still relatively rare, but the situation is likely to change in the coming years.