Comparison PreSonus AudioBox USB96 vs Steinberg UR22

Characteristics of the built-in DAC - a digital-to-analog converter for converting digital audio into line-level analog audio, usually in stereo format.

— Bit depth. Bit size of the digital-to-analog converter (DAC) used in the device. In this case, the meaning of this parameter is as follows: the bit depth of the DAC must be no lower than the bit depth of the audio signal with which the converter is planned to be used, otherwise the device will not be able to effectively cope with the conversion. As for specific values, the standard options in modern audio interfaces are 16 bit, 24 bit and 32 bit.

- Sampling frequency. The sampling rate of the digital-to-analog converter (DAC) installed in the audio interface. Let us recall that such a converter is responsible for converting digital audio into an analog audio signal. The paragraph usually indicates the maximum value of the sampling frequency, for which one of the standard values corresponding to a certain sound quality is used ( 48 kHz, 96 kHz, 192 kHz).

The audio frequency range supported by the device. Most often we are talking about the range of frequencies that a device can produce in an analog audio output signal.

In general, the wider the frequency range, the fuller the sound, the lower the likelihood that the audio interface will “cut off” the upper or lower frequencies. However, it must be taken into account that the human ear is capable of hearing sounds at frequencies from 16 to 22,000 Hz, and the upper limit decreases with age. So from a practical point of view, it makes no sense to provide a wider range in audio technology. And the impressive numbers found in high-end devices are rather a “side effect” of advanced electronic circuits and are given in the specifications mainly for advertising purposes. Also remember that the overall sound quality is affected by many other factors besides frequency range.

Connectors used to connect musical instruments (acoustic or bass guitars, keyboards, etc.). Most often they are made in the form of 6.35 mm Jack format sockets, but there are other options (see below). The audio signal from pickups has its own specific characteristics, so the instrument input typically features a higher input level and special impedance matching to ensure optimal sound quality.

— Jack (6.35 mm). Jack sockets (6.35 mm) are most widely used as instrument audio input. They are very large in size, thereby ensuring tighter contact, and support a balanced connection (for transmitting a high-quality signal without interference over fairly long wires). The number of Jack connectors (6.5 mm) usually corresponds to the number of tools that can be simultaneously connected to the device.

- XLR. A characteristic round connector, often combined with a Jack interface (6.5 mm). XLR is equipped with a locking lock and three contacts (there are other options in terms of quantity, but they are practically not found). The connector is used to transmit an analog signal through a balanced connection, which provides high immunity to interference - sufficient for professional use.

The type of line input provided in the device. Uses the line input to feed audio from an external source to the audio interface.

The following types of connectors can be used for line input:

— mini-Jack (3.5 mm). A socket for a standard mini-Jack plug (3.5 mm). The connector serves as an audio input for two stereo channels. It is designed primarily for portable electronics such as smartphones, pocket players, etc. In stationary devices, Jack (6.35 mm), XLR and RCA are more popular.

— Jack (6.35 mm). A common audio connector for transmitting an analog signal. In design, this type of socket is as similar as possible to a mini-Jack (3.5 mm), but differs in size. Jack connector (6.5 mm) provides tight contact and is less susceptible to interference. It also supports a balanced connection - high-quality transmission of audio signals over fairly long wires with effective protection against interference.

- XLR. The XLR standard is considered professional - not only because of the high quality of signal transmission, but also because of its fairly large size and the presence of locks for securely securing the plugs. However, only one channel of audio can be transmitted over one cable, so XLR outputs are usually installed in pairs - based on stereo sound. Also note that these connectors can be combined with Jack sockets (6.35 mm). They also allow y...ou to implement a connection in a balanced format with a high degree of noise immunity and the use of fairly long wires without affecting the frequency of the analog signal.

- RCA. Connector for coaxial cable with tulip type plug. The standard RCA input consists of two jacks - for stereo sound, left and right channel. One analog RCA connector can only transmit one channel of audio, so the number of such connectors corresponds to the number of channels supported by the device.

Through the Main outputs it is supposed to transmit signals from the audio interface to external devices for playing and recording sound. In everyday use, there are models with one type of Main connector, as well as with several varieties (for example, Jack (6.35 mm), XLR, RCA, or Jack (6.35 mm) / RCA, or Jack (6.35 mm) / XLR).

— Jack (6.35 mm). Output for transmitting analog audio signal. Structurally similar to the popular mini-Jack, but differs from it in its larger dimensions. As a result, Jack type plugs (6.35 mm) are used primarily in high-end stationary audio equipment. Outputs of this type usually operate on a “one channel per connector” principle (i.e., to transmit stereo sound you will need to use two Jack sockets). Also, this interface often provides a balanced connection - a connection in a special format that allows the use of long wires without compromising the signal quality (due to the suppression of interference in the wire itself). However, the Jack connection (6.35 mm) may also be unbalanced.

- XLR. Another type of output for transmitting an analog signal using a balanced connection. It allows the use of long cable lengths without compromising the quality of data exchange - external interference is absorbed directly in the cable. Often the connector is combined with a Jack interface (6.5 mm). The XLR is equipped with a locking lock and three contacts. A single three-pin an...alog cable can only carry one channel of audio, so a standard XLR output typically consists of two jacks, stereo left and right.

- RCA. Jacks for coaxial cables with characteristic plugs, popularly known as “tulips”. One cable in analog format can transmit one channel of audio. The standard output of this type consists of two connectors - for the left and right stereo channels. On the other hand, RCA does not provide the possibility of a balanced connection, which is why it is inferior to other options in noise immunity, has noticeable limitations on cable length and is poorly suitable for professional use. Nevertheless, “tulips” have become very widespread in entry-level and mid-level stationary audio equipment.

The type of line output provided in the audio interface design. It outputs a line-level analog audio signal. This interface is mainly used for connecting recording devices, outputting a signal to playback equipment or to an external amplifier. And the types of connectors used for linear output can be as follows:

— mini-Jack (3.5 mm). A standard socket for the popular mini-Jack plug (3.5 mm), used as a line output. This connector is mainly used to connect some models of active speakers, while two stereo channels are usually output through one mini-Jack (3.5 mm). Note that headphone outputs, which also use a mini-Jack, are considered separately - see the corresponding paragraph.

— Jack (6.35 mm). A larger analogue of the mini-Jack connector (3.5 mm) for outputting an analog stereo signal. The Jack output provides a more reliable and noise-free connection, making it ideal for professional applications. Effective protection against interference is possible with a balanced connection method. To save space, the 6.35 mm output can be combined with an XLR connector (see the corresponding paragraph). The disadvantage of this design is the impossibility of using both interfaces simultaneously. Jack line outputs (6.35 mm) adhere to the “one channel per connector” principle.

- XLR. A round three-pin connector for outputting a line-level analog audio signal, oft...en with a balanced connection type. Transmission is carried out over three wires instead of two, and during it the noise induced on the wire is eliminated. This allows the use of fairly long cables without compromising the “purity” of the signal, making this type of connection excellent for professional audio equipment. XLR is also considered a professional interface, both due to the ability to work with a balanced signal and due to increased reliability: such connectors are often equipped with locks to secure the plugs.

- RCA. Analog linear audio output using RCA connectors - so-called “tulips” (due to the characteristic shape of the plugs). The standard output of this type consists of two connectors - for the left and right stereo channels. Also note that RCA connectors can be used in other output interfaces, but they have their own names.

Output connectors for connecting monitor speakers or headphones. Connecting monitors to the output of an audio interface allows musicians, sound designers, or sound engineers to monitor audio quality in real time. In audio interfaces, monitor outputs can be made in various formats, but most often there are various combinations of RCA, XLR and Jack connectors (6.35 mm), less often - the classic mini-Jack (3.5 mm).

There is a headphone jack on the front panel of the device. This is convenient because the user can easily and quickly connect or disconnect headphones without having to fumble for the corresponding output on the back wall of the audio interface.

The software included with your audio interface may vary depending on the make and model. The vast majority of it is represented by drivers, utilities for managing the device, software for recording and editing sound, virtual instruments or effects, and all kinds of plugins. It is advisable to clarify separately which specific software components are included in the audio interface package.