Gamepads included
The number of gamepads supplied with the console.
Recall that the gamepad is a game manipulator in the form of a small remote control with buttons, levers and other controls. Such devices are used as standard controllers in most desktop consoles (see "Form Factor"). And the number of gamepads corresponds to the number of players who can simultaneously use the console. Most often, there is only one controller in the kit, but many models come with
2 gamepads at once — based on multiplayer for two players, for example, football, fighting or cooperative shooting.
Please note that some models may have specific gamepad counting rules. So, for the Nintendo Switch (see "Form factor — portable / desktop"), a pair of controllers, which in desktop mode is combined into one manipulator, is still considered exactly two gamepads.
Screen size
The diagonal of the set-top box's own display. The display is by definition found in handheld models and game pads (see Form Factor); in desktop models, this element of equipment is quite rare and is usually installed not in the set-top box itself, but on standard controllers (which sometimes can even work as separate devices).
The larger the display size, the larger, respectively, the overall size of the image that the user sees on the screen. However, it is worth considering 2 points. Firstly, an increase in the display size has a corresponding effect on the dimensions of the set-top box itself, and therefore even in advanced tablets it does not exceed 7". Secondly, the image quality depends not only on the size of the display, but also on its resolution (see below). Moreover, at the same resolution, the picture on a larger screen will be less clear and more "grainy" due to the larger pixel size.
Resolution
Set-top box native display resolution. This parameter largely determines the quality of the image: the higher the resolution (with the same diagonal) — the more even and smoothed the “picture” will be, the less noticeable will be the individual points that make up it. Here, however, it must be borne in mind that the corresponding graphics resolution should be provided for in the games themselves. Ideally, it should match the display values — otherwise the image will look either too rough, "grainy" (if the game resolution is less than that of the screen), or small and cloudy (if the game resolution is higher). However, most platforms for portable models have certain requirements for screens, and manufacturers, even unofficial ones, usually try to follow them.
Communications
— LAN (Local Area Network). The most common and in fact the dominant interface today for wired connection of various electronic devices to computer networks. Allows you to work with local resources, as well as access the Internet. In the case of game consoles, such a connection can be used for network games, for working with specialized gaming services, cloud storage, firmware updates, and even for full-fledged web surfing and/or playing music and videos from local resources or Internet sites; specific network capabilities in different models are different. Note that the LAN interface is installed exclusively in desktop consoles (see "Form factor") — it is poorly suited for portable ones for a number of reasons.
— Wi-Fi 4 (802.11n). Game consoles use
Wi-Fi wireless technology primarily to access the Internet. The ways of using such a connection can be different: multiplayer games, access to branded gaming services, social networks, full-fledged web surfing, updating games or firmware, etc. This method of connection is more convenient than wired, because it eliminates the hassle with cables; and for portable models (see "Form factor"), it is actually the only possible one. Specifically, the Wi-Fi 4 (802.11n) standard provides data transfer rates up to 300 Mbps and uses two bands — 2.4 GHz and 5 GHz. The latter ensures compatibility with both earlier (Wi-Fi 802.11 b/g) and later (Wi-Fi 5) standards. And the mentioned speed is consider
...ed relatively low, but for most tasks it is more than enough.
— Wi-Fi 5 (802.11ac). Further, after the Wi-Fi 4 described above, the development of Wi-Fi technology. It uses the 5 GHz band and gives a data transfer rate of more than 1 Gbps (in the future — up to 6 Gbps). This speed not only simplifies the transfer of large amounts of data (for example, downloading games or updates to them), but also reduces lag in online games. For compatibility with older Wi-Fi standards using the 2.4GHz band, Wi-Fi 4 may also be supported in addition to Wi-Fi 5.
— Wi-Fi 6 (802.11ax). The latest version for 2020 uses the ranges from 1 to 7 GHz — that is, it is capable of operating at standard frequencies of 2.4 GHz and 5 GHz (including with equipment of earlier standards), and in other frequency bands. The maximum data transfer rate increased to 10 Gbps, however, the main advantage of Wi-Fi 6 was not even this, but further optimization of the simultaneous operation of several devices on the same channel (improvement of the technical solutions used in Wi-Fi 5 and WiGig). Thanks to this, Wi-Fi 6 gives the smallest speed drop among modern standards when the channel is loaded.
— Wi-Fi 6E (802.11ax). The Wi-Fi 6E standard is technically called 802.11ax. But unlike basic Wi-Fi 6, which is named similarly, it provides for operation in the unused 6 GHz band. In total, the standard uses 14 different frequency bands, offering high throughput in the most crowded places with many active connections. And it is backwards compatible with previous versions.
— Wi-Fi 7 (802.11be). As in the previous edition of Wi-Fi 6E, the technology supports operation in three frequency ranges: 2.4 GHz, 5 GHz and 6 GHz. Wi-Fi 7 bandwidth has increased from 160 MHz to 320 MHz, allowing larger amounts of data to be transferred overnight. IEEE 802.11be uses 4096-QAM modulation, which also allows more symbols to be accommodated in a data transmission unit. The maximum you can squeeze out of the standard is up to 46 Gbit/s information exchange speed. In the context of game consoles, the development of MLO (Multi-Link Operation) looks like a useful innovation, with which you can aggregate several channels in different ranges. This significantly reduces delays in data transfer, while simultaneously ensuring low and stable ping in games. And when connecting multiple client devices, Multi-RU (Multiple Resource Unit) technology is designed to minimize possible delays.
— Bluetooth. Wireless interface designed for direct connection between various devices; very versatile and can be used for a variety of purposes. In game consoles, use cases for Bluetooth include connecting wireless controllers, headphones and headsets, and sharing files with other gadgets (such as a laptop or tablet); the specific capabilities of this interface are different in different models. Bluetooth uses the radio range and has a range of about 10 m, while it can maintain a connection even through walls (except that the range in this case is reduced).
— NFC. NFC (Near Field Communication) is a wireless communication technology with a short range, of the order of several centimeters. Potentially, it has quite extensive capabilities, but today it is most often used as an auxiliary tool when connecting via Wi-Fi or Bluetooth. If both connected devices have an NFC, instead of searching, connecting, authorizing and other actions, it is enough to bring these devices to each other and accept the connection. The vast majority of game consoles with an NFC are portable (see Form Factor).
