Comparison Shanling M3 Ultra vs Shanling M3X

The maximum size of the memory card that can be used in the player. This parameter is directly related to the card type (see above): each type has its own volume limits. At the same time, the ability to work with capacious media is limited not only by the type of card, but also by the player's hardware. Therefore, many models have a lower capacity limit than the memory card suggests — for example, 128 GB in a model that supports the SDXC format (the theoretical maximum for which is 2 TB).

Note that the reverse situation also occurs — for example, when a device with a maximum capacity of 16 GB only supports microSD cards (theoretical maximum is 4 GB). This usually means that the player can work with newer formats (in our example, at least microSDHC), but for some reason this point is not mentioned in the official specifications (for example, the manufacturer could make a mistake in the documentation).

The ratio between the level of the useful signal (clear sound) and extraneous noise, given by the player at the output. This parameter directly characterizes the quality of the built-in amplifier: it mainly takes into account the intrinsic noise of electronic circuits, and the higher the signal-to-noise ratio, the less these noises and the clearer the sound.

Note that in the case of players, this characteristic is often not particularly critical: the noise of the amplifier can be lost against the background of ambient sounds, especially in an urban environment, and for such situations even the most modest indicators, at the level of 70 – 80 dB, are enough. At the same time, for Hi-Fi models (see "Type") this moment is one of the most important; in the most advanced devices, the signal-to-noise ratio can exceed 120 dB.

The higher the power, the louder the sound you can get on the headphones, all other things being equal. In addition, higher power allows you to connect "ears" with higher impedance to the device (although there is no hard correlation here, and models with the same output power may have different headphone impedance limits). However, in the case of ordinary (non-Hi-Fi) players, this parameter is more of a reference than practically significant: usually, the power of the amplifier in such models is quite enough to “rock” most consumer-grade headphones. But for Hi-Fi devices (see "Type") models, output power is of key importance: it determines compatibility with high-resistance studio-class "ears". Detailed help on this issue can be found in special sources.

The coefficient of harmonic distortion produced by the player.

This parameter directly characterizes the amount of distortion introduced by the device into the original sound: the lower the coefficient, the clearer the sound, the less such distortion. It is impossible to completely eliminate them, but they can be reduced to a level that is practically not perceived by a person. So, it is believed that distortions at the level of 0.5% are already invisible even to an experienced listener. At the same time, in modern audio technology, there are also much lower values \u200b\u200b- up to ten thousandths of a percent. In the case of players, such indicators play mainly an advertising role — they are a sign of a high level of the device.

Note that the coefficient of harmonic distortion is indicated mainly for Hi-Fi players (see "Type"), for which the maximum purity of sound is critical; in conventional models, it is of secondary importance.

Wi-Fi technology support by the player. The traditional way to use this feature is to connect to the Internet or local area network through a wireless router; in addition, direct Wi-Fi communication between two devices is also possible.

Normal listening to music does not require these features; therefore, this function is found mainly in media players (see "Type") with extensive additional features. And for models with OS (see above), Wi-Fi support is almost mandatory, because modern operating systems are tightly integrated with the Internet. Specific options for using Wi-Fi depend on the functionality of the player. These may include, but are not limited to, firmware updates, use of audio and video streaming services, Internet radio, installation of applications from online storages, web surfing through a browser, access to social networks, etc.

The player supports Bluetooth technology.

This technology is designed for direct wireless communication between different devices. There are different ways to implement it in players. The most common option is to broadcast sound to wireless headphones, acoustics or other similar equipment (aptX is highly desirable, see “Features/capabilities”). Other methods of application may also be envisaged - in particular, exchanging files with other devices and remote control (player or from the player). The specific set of additional functions should be clarified separately.

Bluetooth wireless protocols from the 4th revision and newer are relevant today:

• Bluetooth v 4.0. Revision 4.0 introduced a Bluetooth Low Energy (BLE) connection mode with low power consumption. This communication standard is intended mainly for transmitting small amounts of information - in particular, service data packets to maintain a connection. At the same time, the creators managed to combine economical energy consumption and a long communication range - it can reach 100 m, which has a positive effect on the stability of the connection.
• Bluetooth v4.1. Development and improvement of Bluetooth 4.0. In terms of players, the key innovation in this version was improved noise immunity when working near 4G (LTE) mobile communication devices (in earlier standards, Bluetooth and LTE signals could overlap, which led to failures).
• Bluetooth v4.2. Further..., after 4.1, development of the Bluetooth standard, which mainly presented a number of general improvements in the reliability and noise immunity of the connection.
• Bluetooth v5.0. Major Bluetooth update released in 2016. One of the most notable innovations was the introduction of two additional operating modes of Bluetooth LE: an increased speed mode (by reducing the range) and an extended range mode (by reducing the speed). The key benefit of these innovations is to improve the overall reliability of communications, increase their range and reduce the number of breaks.
• Bluetooth v5.1. Update to revision v 5.0, in which, in addition to general improvements in the quality and reliability of communication, it became possible to determine the direction from which the Bluetooth signal is coming. Thanks to this, the location of connected devices is determined with centimeter accuracy, which has a positive effect on the quality of the wireless connection.
• Bluetooth v5.2. The next update, after 5.1, is Bluetooth 5th generation. The main innovations in this version are a number of security improvements, additional optimization of power consumption in LE mode and a new audio signal format for synchronizing parallel playback on multiple devices.
• Bluetooth v 5.3 came into use at the dawn of 2022. Among the innovations in it, they accelerated the process of negotiating a communication channel between the controller and the device, implemented the function of quickly switching between the operating state in a low duty cycle and a high-speed mode, and improved the throughput and stability of the connection by reducing susceptibility to interference. When unexpected interference occurs in Low Energy mode, the procedure for selecting a communication channel to switch from now on has been accelerated.
• Bluetooth v 5.4 was introduced at the beginning of 2023. This edition has increased the range and speed of data exchange. Also in Bluetooth v 5.4, the energy-saving BLE mode has been improved. This version of the protocol uses new security features to protect data from unauthorized access, has increased connection reliability by selecting the best channel for communication, and prevents connection losses due to interference.

The capacity of the battery installed in the player.

Theoretically, a larger battery can provide longer battery life. However, in fact, battery life will depend not only on the capacity of the battery, but also on the power consumption of the player, and it is directly related to the functionality. Therefore, when evaluating battery life, it is better to focus not on battery characteristics, but on the operating time directly stated in the characteristics (see below). And only models with similar characteristics can be compared with each other in terms of battery capacity — for example, media players on Android with approximately the same screen sizes.

The maximum time the player can operate on one battery charge in audio playback mode. You should pay attention to this parameter first of all if you have to use the device for a long time without the ability to recharge the battery. At the same time, note that manufacturers usually indicate an “perfect” operating time: at a constant relatively low volume, without working with the screen and other additional functions that also consume battery. And this means that in fact the battery life of the player may be somewhat lower than stated. Nevertheless, this parameter allows you to fairly accurately assess the suitability of the player for long-term work without recharging, and is also quite suitable for comparing different models with each other.