Comparison Hotcig Kubi Refillable Pod Kit vs Wismec Bambino RDA

- Starter kit. A complete set, also known as a "kit" or "box mod". Includes everything you need for vaping - both a battery mod and an atomizer; in other words, a “kit” is a ready-to-use electronic cigarette (except that the battery in some models has to be purchased separately). At the same time, in this category there are both relatively inexpensive and simple devices, as well as high-end models. In any case, starter kits will be appreciated by tech who do not want to pick up a battery mod and an atomizer separately and would like to immediately get a device whose components are optimally compatible with each other.

- POD system. A specific type of electronic cigarette that uses not traditional atomizers, but replaceable cassettes - “pods”. Each such cassette consists of an evaporator and a container with liquid; "pod" can be either open (with the possibility of refilling at your discretion) or closed (disposable, supplied refilled and discarded when the supply of liquid is exhausted). In any case, POD systems are usually sold as ready-made kits, which have a number of advantages over traditional vapes. First, cassettes are relatively inexpensive and take up very little space; as a result, you can carry several “pods” with you at once with different tastes and / or fortresses, changing them in a battery fashion at will. Seco...ndly, the battery mods themselves turn out to be more compact and lighter than in conventional electronic cigarettes, they are more convenient to carry and do not attract attention as much. Thirdly, POD systems are extremely easy to maintain - in fact, it makes no sense to make replaceable cassettes serviceable. Among the disadvantages of such devices, one can note the relatively small capacity of batteries and reservoirs in cassettes, although there are exceptions.

- Disposable. Disposable POD systems are vape devices without the possibility of refilling liquid and recharging the battery. The liquid reservoir in their design has a certain volume, and a specific battery capacity is selected for it (based on the specified number of puffs). When the e-liquid runs out or the battery runs out, the device can be thrown away. Due to their compact size, disposable electronic cigarettes fit easily into a pocket of clothing, a small compartment of a bag or backpack. Also, they often lack controls and settings - the heating element is activated immediately, as soon as the customer takes a puff. There are many different options for disposable POD systems on the shelves in terms of taste.

- Atomizer. Separately sold e-cigarette vaporizer - that is, the part in which the formation of vapor occurs; for operation, the vaporizer is installed on a battery mod (see below). Some types of such devices are also called "clearomizers", but this term is becoming less common, in our time, usually all evaporators are combined under the term "atomizer". Be that as it may, the overall vaping experience is mainly influenced by the characteristics of the evaporator: in particular, the taste and saturation of the vapor directly depend on them, as well as the ability to adjust the vapor to your preferences. So in order to change the feeling of vaping, just try a different atomizer. In addition, when buying a new vape, many users (especially experienced ones) prefer not to rely on ready-made starter kits, but to choose an atomizer and a battery mod separately, at their discretion.

- Battery mod. The part of an electronic cigarette that powers the vaporizer (atomizer). The functionality of such a mod can be different - from the simplest container for a replaceable battery with an on / off button to an advanced device with complex control electronics and advanced features (see "Battery Mod"). Be that as it may, separately sold battery mods are designed for tech who want to build a custom e-cigarette without relying on starter kits.

The type of battery mod supplied separately or as part of a starter kit (see "Type"). In this case, battery mods are divided into types according to the presence or absence of additional boards; the types of batteries used are listed in a separate paragraph (see "Battery type")

— Electronic. Battery mods that have additional control electronics (“board”) in their design — in addition to the battery (battery compartment) and the power button. Such a board contains at least a charge / discharge controller, and often additional settings such as wattage or thermal control (see "Board functions"). Electronic battery mods, even the simplest ones (having only a power button), are noticeably more complicated than mechanical counterparts, which somewhat reduces reliability. On the other hand, they are more convenient and, most importantly, safer: the board provides the optimal battery operation mode, which minimizes the likelihood of its overload and related troubles. Therefore, this option is highly recommended for novice users. However, it is also preferred by many experienced vapers — electronics allow you to enjoy the vapor without worrying too much about the battery life.

— Mechanical. He is also a " mechmod ". The simplest battery mods, consisting of a case, a power on/off button and a battery compartment (usually removable). Power to the atomizer in such devices is supplied directly from t...he battery, without the use of control circuits; An external charger is required to charge the battery. In addition to simplicity and low cost, the advantage of mech mods is the extended possibilities for experimenting with power. On the other hand, such devices require careful handling and strict adherence to the battery charging / discharging regimen. At the same time, the user himself must monitor the mode, and violation is fraught with malfunctions and corresponding troubles (suffice it to say that the infamous battery explosions happened mainly on mechanical mods). In light of all this, the “mechanics” is suitable only for experienced vapers who are attentive to the correct use of the “materiel”.

— Unattended. Maintenance-free called atomizers-tanks (with a container for liquid), in which, in principle, it is impossible to replace the factory heater (spiral and wick) with its own winding. Thus, when using such an evaporator, you will have to periodically (most likely once every 2-3 weeks) change the “heads” (heaters). Maintenance-free vapers are a good option for those who are just about to try vaping, as well as for experienced vapers who don't want to mess around with custom coils. Their main disadvantage is the inability to adjust the atomizer to your own preferences — you have to make do with what the manufacturer originally provided for in the design.

— Serviced. Tank atomizers (with a container for liquid), in the design of which the manufacturer initially provides for the possibility of replacing the heating element (coil and wick) by the user. This is more difficult than changing the whole “head”, as in a maintenance-free atomizer; but winding can be done according to your own preferences, without relying on a factory design, and consumables for winding are cheaper than whole heads. On the other hand, the possibility of replacing the entire “head” in such models is most often not provided for — the only option is manual winding. In light of all this, serviceable atomizers will be a good choice, especially for experienced vapers who want to have the maximum opportunity to personaliz...e their electronic cigarette.

— Semi-maintenance. Tank atomizers (with a liquid container) that combine the capabilities of serviced and non-serviced models. In such a “tank” it is possible to install both unattended “heads”, which are completely replaceable, and serviced heaters, which can be rewound by the user himself. Thus, the vaper can choose the option of his choice: either use simple and convenient interchangeable “heads”, or spend a little time and effort, but wind the coil according to his own preferences. On the other hand, most users do not need such versatility, so relatively few atomizers of this type are produced.

— Drip atomizer (RDA). A distinctive feature of this type of atomizer is the absence of a liquid container: before each vaping session, the wick must be moistened directly from the bottle with a few drops of liquid (hence the name drip). This is not as convenient as having a tank with a supply of liquid for several sessions on hand — in particular, also because it is not easy to control the remaining liquid in the drip. On the other hand, this option has an important advantage: due to the excellent blowing of the heating elements, the “drips” give a very plentiful and saturated steam, in this indicator they are noticeably superior to the tanks. And so that such an atomizer does not have to be frequently refilled manually, manufacturers can provide various tricks — for example, in the so-called "squonkers" have a tank installed in the battery pack, and from this tank, by pressing the "feed" button, the evaporator wick is fed.

— Bacodripka (RDTA). Combined devices, in accordance with the name, combining both a tank and a drip. From the first variety of RDTA, they took a tank for themselves, which allows them to keep a supply of liquid on hand for several soaring sessions, from the second — a heater design that provides abundant and intense steam. Thus, such atomizers combine the advantages of both types. On the other hand, baco drips are expensive, have a very high fluid consumption, and are often difficult to maintain: in many models, cotton wool plays the role of a wick, which must be laid in a special way when replacing — otherwise leakage or burning is possible.

— Genesis. A specific type of atomizer tanks, usually serviced (see above). The key difference between the Geneses is the design of the wick: it is a fine stainless steel mesh wrapped with a heater coil. This gives a number of advantages compared to the classical design, where the wick is made of cotton wool, vegetable fibers, etc. Taste is considered the main of these advantages: genesis does not give a burnt aftertaste and provides almost perfect steam purity. In addition, such "heads" can serve without replacement for a very long time (several months), and the replacement of the wick and the heater is quite easy and fast. The main disadvantage of this type of atomizers is their rather high cost. Separately, we note that the installation of a metal wick in a classic evaporator does not turn it into a genesis — the design of the atomizer must be initially optimized for the grid.

The volume of the liquid tank provided in the design of the atomizer. Note that this parameter can be specified even for squonk atomizers (see "Filling type"): although they work with an external tank, however, a certain amount of "liquid" can fit in the evaporator itself.

The larger the tank, the more liquid you can keep in an electronic cigarette and the less often you have to refill it. On the other hand, capacious tanks have the appropriate dimensions, and too large a tank would be inconvenient, and liquids are consumed relatively little even in one long session of soaring. As a result, a volume of more than 6 mL is already considered quite large for vapes, and in the smallest models this figure does not exceed 2 mL.

Also note that when choosing a tank capacity, manufacturers usually take into account the resistance of the spiral, the power of the battery (if it is included) and other parameters that affect the expected flow rate of the liquid. There is no hard dependency here, however, in general, more powerful atomizers are usually equipped with larger tanks.

— Upper. The traditional type of filling was initially quite popular, but now such atomizers are gradually giving way to bottom filling models. The main advantage of this option is the ability to pour liquid without turning the atomizer over and without removing the flask from the battery mod. However refilling usually requires disassembly — for example, unscrewing the cap with the mouthpiece.

— Lower. This option assumes that for refueling, you need to turn the atomizer upside down and pour liquid from the bottom side. At first glance, this procedure is less convenient than top filling, but it provides an important advantage for serviced heaters: if necessary, you can remove and rewind the base without draining the liquid from the tank. Note that squonk format drip atomizers are formally also refueled from below, however, they have their own specifics, therefore they do not belong to this category and are allocated separately; see below for details.

— Side. Refueling through a special hole in the side of the atomizer. Like the top one, this design allows you not to remove the flask from the battery mod; the opening usually opens and closes easily and quickly, without the need, for example, to unscrew the cap. This option is quite popular in baco drips (see "Type of atomizer"), althou...gh it is also found in other varieties.

— Squonk. A specific type of bottom filling used in models with drip atomizers (see "Type of atomizer"). These vapes have a rather large e-liquid reservoir installed in the battery mod, and each time you press a special button (or the elastic wall of the reservoir), the liquid is fed into the atomizer in small portions directly through the connector. This design eliminates the main drawback of drip atomizers — the need to constantly add liquid manually, "drop by drop": instead of the hassle of manual refueling, it is enough to periodically press the button. At the same time, most of these evaporators allow installation on a regular battery mod, without a squonk — for this, the kit provides a replaceable connector of a standard design, without a channel for supplying liquid; and on battery mods with a squonk, usually, you can put ordinary atomizers without restrictions. The disadvantages of this option can be somewhat higher cost than analogues with traditional types of refueling.

The number of individual heating coils provided in the atomizer.

The simplest design option provides only 1 spiral, however, 2-spiral atomizers have gained the most popularity: it is easier to achieve intense and saturated steam in them (however, for efficient operation, higher power is required, and the liquid flow rate is higher). However, it is worth noting that there is no rigid connection between the level of the atomizer and the number of heaters: among other things, there are advanced models with one coil, and low-cost solutions with two.

There are also more spirals — three or even four, but such solutions are quite expensive, difficult to maintain and high consumption in terms of energy consumption, which is why they have not gained distribution.

The type of blowing provided in the atomizer of an electronic cigarette.

This parameter is indicated by the location of the cells for the intake of air entering the evaporator. According to this criterion, lower, upper and side airflow are distinguished, here are their main features:

— Lower. The most popular option nowadays. Such popularity is primarily due to the fact that many vapers consider the “lower” vapor to be the most delicious. In addition, bottom blown atomizers are easier to maintain than "side" models, they are not so demanding on winding quality. The disadvantages of this option include an increased likelihood of leakage, including during liquid overflow; and the condensate, which is quite intensively formed at the air intakes, tends to flow down onto the battery mod. However, these points are not particularly critical.

— Upper. A format that has appeared relatively recently. In general, such an airflow conveys taste somewhat worse than the lower one, moreover, the steam turns out to be hotter; however, this point is largely subjective, and some users like this type of steam. The objective advantages of the “upper” atomizers include the minimum probability of overflow, the almost complete absence of condensate flowing onto the battery mod, and the absence of splashes even when using coils with very low resistance.

— Si...de. The type of blowing used mainly in "drips" (see "Type of atomizer"). If the bottom airflow gives the most delicious steam, then the side airflow is the most dense and saturated. This is achieved due to the fact that the air flows around the spiral as intensively as possible and captures the greatest amount of evaporation. In addition, the likelihood of liquid overflow and splash formation in such atomizers is very small, and with the right settings, the taste is transmitted almost as well as in the “lower” models. The main disadvantage of this option is the actual need for careful tuning and proper installation of the spiral — so that there are no blind spots on it. So side airflow is generally designed for experienced users; maintenance-free atomizers are an exception, but this format of operation is rarely used in them.

Also note that there are combined options for sale, for which two types of airflow are indicated at once. Here the specifics can be different. So, it is unrealistic to combine the upper and lower airflow in one evaporator, therefore this option is indicated only for sets of several atomizers with different types of airflow. But the side format of work may well be combined with the top or bottom — this allows you to combine the advantages of both options and provide saturated steam. On the other hand, the need for careful tuning for such devices is just as relevant as for "pure" side ones.

Systems that are activated and give steam not with a button, but at the moment of puffing. This solution makes it easier to smoke, since it is not necessary to constantly hold the button. Plus , activation on a puff eliminates the likelihood of accidental pressing when carried in a pocket, bag, etc.

The highest resistance of the electronic cigarette heating coil.

The meaning of this parameter will be different, depending on which part of the device is in question (see "Type"). For an atomizer, this can be either the resistance of the complete heater, or, if there are several “heads” in the kit, the resistance of the highest-resistance replaceable coil. For a battery mod, the highest resistance is indicated at which the battery is able to deliver sufficient power for operation. For the starter set, the data is usually given according to the battery mode, while the resistance of the complete heater (heaters) may be lower than the maximum.

Data on the maximum and minimum (see above) resistance is necessary, first of all, to select an atomizer and a battery mod that are compatible with each other. The atomizer must fall within the operating range of the battery mod, otherwise the battery will either be overloaded (if the evaporator resistance is too low), or simply will not provide the desired degree of heating (if it is too high).