Comparison Voopoo Drag 2 177W vs Tesla Invader IV 280W

Additional functions of the board provided in the electronic battery mod (see "Battery mod").

— Varivolt. Battery mods that allow you to adjust the voltage supplied to the atomizer. Due to this, the power supply changes and, accordingly, the heating power and the general vaping mode are regulated. At the same time, unlike the varivolt (see below), the voltage change in the varivolt is carried out only manually, regardless of the resistance of the atomizer. In fact, this means that if the user wants to get the same power on an atomizer with a different resistance, he will have to reconfigure the varivolt.

— Variwatt. Battery mods with the ability to automatically maintain the specified power supplied to the atomizer. An automated version of varivolts, which is able to automatically adjust to changes in the resistance of the atomizer. The voltage in the variatt is set for a specific resistance of the atomizer; if the resistance changes, then the electronics automatically sets the voltage at the output of the battery mod so that the power remains unchanged. Thanks to this, you can put heaters with different resistances on the battery pack without worrying about reconfiguring the power parameters — the variatt will independently select the desired voltage, keeping the intensity of soaring at the usual level. The main disadvantage of this option compared to...the varivolt is the relatively high cost, and compared to thermal control(see below), the need to choose the power experimentally, by trial and error.

— Variwatt + Varivolt. Battery mods capable of operating in two different modes — varivolt or variwatt, at the request of the user. These modes are described in more detail separately, and their combination in one battery pack can be useful for those who appreciate the advantages of vari-watt, but are not averse to experimenting with vari-volt as well.

— Thermal control + variatt. Battery mods that combine the variatt capabilities described above with the thermal control function. Thermal control allows you to monitor the temperature of the spiral, maintain it at an optimal level and turn off the power when approaching critical heating. The combination of these two adjustments is the most advanced option for today, in fact, eliminating the need for the vaper to manually select the optimal power settings. At the same time, the steam turns out to be pleasant to the taste (both due to its own temperature, and due to the fact that the probability of burning the wick is reduced to almost zero), and the battery charge is consumed in an optimal way. A serious drawback of thermal control, in addition to a rather high cost, is limited compatibility with atomizers: for this function to work correctly, a “head” with a coil made of nickel or titanium is required, and such models are relatively rare, and they are not cheap in themselves.

— Thermal control. Battery mods, the settings of which are limited only by thermal control. This function is described in more detail above; here we note that thermal control itself does not allow controlling the intensity of soaring, therefore this option has not received much distribution.

The ability to update the firmware of an electronic cigarette — more precisely, a battery mod (this is where all the control electronics are usually located).

This feature is most often found in models with advanced adjustments such as wattage or thermal control (see "Battery mod") — simpler devices do not require complex firmware (although there are exceptions). Major manufacturers of electronic cigarettes periodically release software updates for their equipment that improve the quality of work and eliminate errors noticed by consumers. So this feature is highly desirable for a device with extensive functionality and complex electronics.

The smallest resistance of the heating coil of an electronic cigarette.

The meaning of this parameter will be different, depending on which part of the device is in question (see "Type"). So, for atomizers, this parameter is given if spare heaters are supplied in the kit — accordingly, it is indicated for the “head” with the lowest resistance. For a battery mod, this is the smallest resistance that can be connected to it. And in starter kits, the minimum resistance is also usually indicated by the battery mod; low-resistance "heads" in such cases may or may not be included in the delivery.

Anyway, data on the minimum resistance is important in the mutual selection of an atomizer and a battery mod (including when creating custom windings) — connecting an atomizer with too low resistance is fraught with overloads and various unpleasant consequences, up to fire. However, this parameter is of particular importance for lovers of the so-called subohm — soaring at a low heater resistance (up to 1 ohm), which allows you to achieve high steam saturation (when the resistance decreases, the power increases). Not all batteries are capable of working with sub-ohm heaters, so the suitability of a battery mod for such vaping needs to be clarified.

The maximum power supplied by the battery.

This is one of the main parameters of the battery pack that determines its compatibility with the atomizer. Starter kits (see "Type"), by definition, include atomizers that are optimally suited to a given battery in terms of power, and this parameter is mainly of reference value. But when choosing components separately, you should pay special attention to it. Higher power allows you to achieve more saturated steam, but only up to certain limits — too much heating leads to a deterioration in taste, and even burning of the wick (which, all the more, does not contribute to improving the sensation of soaring). So the atomizer must normally transfer the power of the battery, otherwise, at best, you will have to constantly limit the power with the help of a varivolt or variwatt (see "Battery mod"), and at worst, normal use will be impossible at all.

Note that for classic evaporator tanks with one spiral, power up to 40 W is considered sufficient; more powerful batteries are designed mainly for advanced serviced models, drip atomizers and bacodrips(see "Type of atomizer") that have more than one coil and, accordingly, are more high consumption in terms of energy consumption. Also note that the actual heating power depends on the voltage, and in fact it may be lower than the claimed one, depending on the resistance of the atomizer. See “Maximum voltage".

The lowest voltage that the battery mod can supply to the atomizer.

The meaning of this parameter depends on the type of battery mod and the functions of the board (see above). So, in mechanical and simple electronic modes, the smallest value to which the battery voltage can drop before it turns off and requires charging is usually indicated here. Knowing this parameter, as well as the resistance of the atomizer, you can calculate the minimum guaranteed vaping power.

If we are talking about a mod with adjustments like varivolt or variwatt, then the minimum voltage is also the lowest voltage that can be set manually in the settings. This may be necessary to reduce the power and, accordingly, the intensity of soaring — for example, if the gas station has a very rich taste, and abundant dense steam would be overkill. In adjustable battery packs, the lower the minimum voltage (with the same maximum voltage), the wider the adjustment range, the more options the vaper has to adjust the vaping parameters. See “Maximum voltage".

The highest voltage that the battery mod can supply to the atomizer.

Knowing the minimum (see above) and maximum voltage, it is possible to estimate the heating power that the battery is able to provide at a certain resistance of the atomizer. For example, if we have a battery mod with a voltage range of 3.3 – 4.8 V and an atomizer with a 1.8 Ohm coil, then the current strength at the minimum voltage will be 3.3 / 1.8 ≈ 1.8 A, and at maximum 4.8 / 1.8 ≈ 2.7 A. Accordingly, the smallest heating power will be 3.3 * 1.8 ≈ 6 W, and the largest 4.8 * 2.7 ≈ 13 W. In this case, the nominal power of the battery can be higher, but not vice versa — the actual power cannot be more than the nominal. Let's say, theoretically, the battery from our example, combined with a 0.15 Ohm sub-ohm atomizer, even at the minimum voltage, should produce a current of 3.3 / 0.15 = 22 A and a power of 3.3 * 22 = 72.6 W. However, if a power of 50 W is claimed in the characteristics, then higher values \u200b\u200bare impossible to achieve, even if you unscrew the regulator to the maximum — at low resistances, the voltage at the battery output drops sharply.

The presence of a microUSB connector in the battery mode, through which batteries can be charged.

The main advantage of this feature is that it makes the battery independent of proprietary chargers. The microUSB standard is extremely popular in various portable equipment — smartphones, tablets, players, etc.; accordingly, a huge number of chargers, USB-microUSB cables and network / car adapters for such cables have been released for this connector. Thus, the battery mod can be charged not only from the "native" adapter / cable, but also from any accessory with the appropriate connector. However, note that all of the above applies mainly to models with non-removable batteries. If the battery is made removable (see above), then anyway it is recommended to charge it in a separate charger, and use the microUSB port only in case of emergency. This is due to the fact that in most battery mods for replaceable batteries, the boards are not designed for regular use in charger mode, and frequent use of microUSB charging can lead to premature failure of the board.

The presence of a display in the design of an electronic cigarette — more precisely, a battery mod (see "Type"): putting a display on an atomizer does not make sense for a number of reasons, in particular, because there is not enough space there. But on the battery pack, even a small one, it is quite possible to place a screen. Usually this is the simplest monochrome matrix (black and white or in another colour, say, white characters on a blue background), capable of displaying data in one, at most two lines. However, even with such equipment, control becomes more convenient and intuitive: a variety of digital and textual data can be displayed on the screen, for example, the set voltage or power value, operating mode (variatt / varivolt, if both are supported), battery charge, start message and the end of charging, failure notifications, etc. And some models may even provide advanced touch displays (see below)

The material from which the body of the device is made.

This parameter is relevant primarily for battery mods: they can be made from a wide variety of materials, while atomizers do not differ in variety (the standard option is stainless steel, with a few exceptions; see below for details). Actually, for ready-made kits (including POD systems, see "Type"), this paragraph just indicates the material of the battery mod. Here is a more detailed description of specific options:

— Stainless steel. Perhaps the most popular material for electronic cigarettes and their components — of all types and price categories. At a relatively low cost, stainless steel is strong, reliable, durable and not subject to scratches and corrosion. Of the shortcomings of this material, one can only note a rather large weight, but some, on the contrary, consider this moment an advantage: a massive metal case gives the impression of solidity and quality. Also, steel, like any metal, can cool the skin at low air temperatures and slide in the hands; however, in order to avoid all this, various linings (for example, made of rubber or soft-touch plastic) can be provided on the case to eliminate this drawback.

— Zinc alloy. Another fairly popular material, which is actually a compromise between stainless steel and aluminium. Zinc weighs less than steel and costs less than aluminium alloys; at the same time, this...material perfectly resists corrosion and has high strength, which led to its prevalence.

— Aluminium. Perhaps the most advanced metal in terms of practical characteristics: aluminium is light, strong and absolutely insensitive to corrosion. Its main disadvantage is a rather high price, while the described advantages are rarely decisive in comparison with the same steel or zinc. Therefore, aluminium cases are quite rare; at the same time, it is worth noting that this material is found not only in battery mods, but also in atomizers.

— Plastic. Inexpensive material, which also has a small weight and is able to take on a wide variety of colours. However, this is where the advantages of plastic, in fact, are exhausted: in terms of strength and scratch resistance, it is noticeably inferior to metals, and it can melt from strong heat. However there are advanced grades of plastic, but instead of them, most manufacturers prefer to use steel or other metal in vapes. As a result, plastic cases are rare, and mostly among entry-level models.

— Copper. The material used mainly as a design material — to give the case an unusual appearance (copper has a characteristic reddish tint). From the point of view of practical properties, such cases are similar to steel ones — in particular, they are strong, massive and scratch resistant. On the other hand, copper tolerates moisture worse, stains can appear on it even from constant contact with the skin. However, the main drawback of this material is its high price, which determined the specifics of its application.

— Brass. Another metal used primarily for aesthetic rather than practical reasons. It is similar in properties to copper described above and differs only in colour (shades of yellow) and somewhat greater resistance to oxidation (although it all depends on the specific type of brass).

— Wood. Wooden cases look interesting due to the characteristic colours and patterns. At the same time, this material is not very practical: it is prone to cracks and splits from impacts, it is easily scratched, and it can swell and warp from prolonged exposure to moisture. In addition, wooden cases are quite expensive (in part, this is a payment for the style). So, choosing a battery mod in such a design is worth it only in cases where the ability to “stand out from the crowd” is more important for you than the shortcomings described.

— Ceramics, Special high-strength ceramics are highly resistant to wear: such a case is very difficult to scratch, so it looks like new for a long time. On the other hand, this material may crack on impact (whereas metal is more likely to only slightly bend). Therefore, ceramic cases are extremely rare — especially since they are not cheap.