Comparison Joyetech eGo AIO ECO Kit vs J WELL J Mini Kit

The volume of the liquid tank provided in the design of the atomizer. Note that this parameter can be specified even for squonk atomizers (see "Filling type"): although they work with an external tank, however, a certain amount of "liquid" can fit in the evaporator itself.

The larger the tank, the more liquid you can keep in an electronic cigarette and the less often you have to refill it. On the other hand, capacious tanks have the appropriate dimensions, and too large a tank would be inconvenient, and liquids are consumed relatively little even in one long session of soaring. As a result, a volume of more than 6 mL is already considered quite large for vapes, and in the smallest models this figure does not exceed 2 mL.

Also note that when choosing a tank capacity, manufacturers usually take into account the resistance of the spiral, the power of the battery (if it is included) and other parameters that affect the expected flow rate of the liquid. There is no hard dependency here, however, in general, more powerful atomizers are usually equipped with larger tanks.

The type of blowing provided in the atomizer of an electronic cigarette.

This parameter is indicated by the location of the cells for the intake of air entering the evaporator. According to this criterion, lower, upper and side airflow are distinguished, here are their main features:

— Lower. The most popular option nowadays. Such popularity is primarily due to the fact that many vapers consider the “lower” vapor to be the most delicious. In addition, bottom blown atomizers are easier to maintain than "side" models, they are not so demanding on winding quality. The disadvantages of this option include an increased likelihood of leakage, including during liquid overflow; and the condensate, which is quite intensively formed at the air intakes, tends to flow down onto the battery mod. However, these points are not particularly critical.

— Upper. A format that has appeared relatively recently. In general, such an airflow conveys taste somewhat worse than the lower one, moreover, the steam turns out to be hotter; however, this point is largely subjective, and some users like this type of steam. The objective advantages of the “upper” atomizers include the minimum probability of overflow, the almost complete absence of condensate flowing onto the battery mod, and the absence of splashes even when using coils with very low resistance.

— Si...de. The type of blowing used mainly in "drips" (see "Type of atomizer"). If the bottom airflow gives the most delicious steam, then the side airflow is the most dense and saturated. This is achieved due to the fact that the air flows around the spiral as intensively as possible and captures the greatest amount of evaporation. In addition, the likelihood of liquid overflow and splash formation in such atomizers is very small, and with the right settings, the taste is transmitted almost as well as in the “lower” models. The main disadvantage of this option is the actual need for careful tuning and proper installation of the spiral — so that there are no blind spots on it. So side airflow is generally designed for experienced users; maintenance-free atomizers are an exception, but this format of operation is rarely used in them.

Also note that there are combined options for sale, for which two types of airflow are indicated at once. Here the specifics can be different. So, it is unrealistic to combine the upper and lower airflow in one evaporator, therefore this option is indicated only for sets of several atomizers with different types of airflow. But the side format of work may well be combined with the top or bottom — this allows you to combine the advantages of both options and provide saturated steam. On the other hand, the need for careful tuning for such devices is just as relevant as for "pure" side ones.

The smallest resistance of the heating coil of an electronic cigarette.

The meaning of this parameter will be different, depending on which part of the device is in question (see "Type"). So, for atomizers, this parameter is given if spare heaters are supplied in the kit — accordingly, it is indicated for the “head” with the lowest resistance. For a battery mod, this is the smallest resistance that can be connected to it. And in starter kits, the minimum resistance is also usually indicated by the battery mod; low-resistance "heads" in such cases may or may not be included in the delivery.

Anyway, data on the minimum resistance is important in the mutual selection of an atomizer and a battery mod (including when creating custom windings) — connecting an atomizer with too low resistance is fraught with overloads and various unpleasant consequences, up to fire. However, this parameter is of particular importance for lovers of the so-called subohm — soaring at a low heater resistance (up to 1 ohm), which allows you to achieve high steam saturation (when the resistance decreases, the power increases). Not all batteries are capable of working with sub-ohm heaters, so the suitability of a battery mod for such vaping needs to be clarified.

The type of connector for connecting the atomizer to the battery pack provided in the device. The most popular today are two types of connectors:

ego. A standard used primarily in entry-level starter kits (see "Type"). In such models, the battery mod has the form of a cylinder with a small diameter and, accordingly, does not differ in special power and capacity. The connector itself is screw, and when connected, the battery is screwed into the atomizer (unlike the 510 standard). Charging is also carried out through the ego connector, and, accordingly, requires the use of specialized chargers. For more solid equipment, this connector does not fit well, and therefore is not used in more or less powerful battery packs.

- 510. The most popular modern connector for electronic cigarettes, used in most battery packs and atomizers; installed in almost all devices of the middle and top class, as well as in most low-cost models. Like the ego, it uses a screw connection, however, in this case, the atomizer is screwed into the slot on the body of the battery mod, and not vice versa.

For normal compatibility of the atomizer with the battery mod, it is necessary that both of them use the same connector. However, due to the extreme popularity of the 510 type, problems with this very rarely arise, and in extreme cases, adapters between these standards are produced.

The battery capacity of an e-cigarette or separately sold battery mod. This parameter is indicated only for models with non-removable batteries (see "Battery type"): replaceable cells can be produced in different capacities.

The larger the battery, the longer you can use the device without recharging the battery. However the actual power consumption and, accordingly, the battery life of different models will be different, therefore, only devices with similar operating voltages and atomizer resistances can be compared in terms of capacity.

In general, if battery life is important to you, it is quite possible to proceed from the principle “the more capacious the battery, the better”; and to save money, you can choose a relatively weak battery. It is also worth mentioning that there are schemes for calculating the optimal battery capacity depending on the power, atomizer resistance, etc.; these schemes can be found in special sources.

The lowest voltage that the battery mod can supply to the atomizer.

The meaning of this parameter depends on the type of battery mod and the functions of the board (see above). So, in mechanical and simple electronic modes, the smallest value to which the battery voltage can drop before it turns off and requires charging is usually indicated here. Knowing this parameter, as well as the resistance of the atomizer, you can calculate the minimum guaranteed vaping power.

If we are talking about a mod with adjustments like varivolt or variwatt, then the minimum voltage is also the lowest voltage that can be set manually in the settings. This may be necessary to reduce the power and, accordingly, the intensity of soaring — for example, if the gas station has a very rich taste, and abundant dense steam would be overkill. In adjustable battery packs, the lower the minimum voltage (with the same maximum voltage), the wider the adjustment range, the more options the vaper has to adjust the vaping parameters. See “Maximum voltage".

The material from which the flask of the complete atomizer is made. Most often, it means the material from which the transparent insert in the body (usually steel) is made, with the exception of all-steel flasks, see below for more details about them.

— Glass. The most popular flask material in modern vapes. The glass does more than just allow you to see the contents of the flask — this transparency is maintained for a long time, as the glass surface is highly resistant to scratches. In addition, the walls of the flask are chemically inert, they do not react with the "slurry", whatever its composition; and the fragility of the walls is compensated by their thickness, and sometimes by special additives in the composition of the glass. This material is somewhat more expensive than plastic, but in fact this difference is insignificant.

— Plastic. Plastic flasks, like glass, are usually made transparent, which allows you to monitor the amount of liquid; at the same time, they are much cheaper, it is very difficult to break such a container, and fragments from plastic are not as dangerous as glass ones. At the same time, this material is easily covered with scratches and quickly becomes cloudy during use. In addition, some types of plastic (especially inexpensive ones) can react with substances that make up e-liquids (manufacturers of both flasks and refills try to avoid this phenomenon, but...a full guarantee cannot be given). As a result, this option is not particularly popular, it is typical mainly for low-cost devices created with the expectation of maximum cost reduction.

— Stainless steel. Stainless steel flasks are notable primarily for their high strength — even under a very strong load, the steel tank is more likely to flatten than crack. Yes, and resistance to corrosion can also be written down as advantages. At the same time, this material has a critical drawback that negates all its advantages — it is opaque. As a result, it is possible to monitor the liquid level in such a flask only by indirect signs — for example, by changing the taste or the amount of steam. This, to put it mildly, is inconvenient, so steel flasks are used extremely rarely — and not so much for practical reasons, but as an element of unusual design.