Liquid tank capacity
The volume of the liquid tank provided in the design of the atomizer. Note that this parameter can be specified even for squonk atomizers (see "Filling type"): although they work with an external tank, however, a certain amount of "liquid" can fit in the evaporator itself.
The larger the tank, the more liquid you can keep in an electronic cigarette and the less often you have to refill it. On the other hand, capacious tanks have the appropriate dimensions, and too large a tank would be inconvenient, and liquids are consumed relatively little even in one long session of soaring. As a result, a volume
of more than 6 mL is already considered quite large for vapes, and in the smallest models this figure
does not exceed 2 mL.
Also note that when choosing a tank capacity, manufacturers usually take into account the resistance of the spiral, the power of the battery (if it is included) and other parameters that affect the expected flow rate of the liquid. There is no hard dependency here, however, in general, more powerful atomizers are usually equipped with larger tanks.
Minimum resistance
The smallest resistance of the heating coil of an electronic cigarette.
The meaning of this parameter will be different, depending on which part of the device is in question (see "Type"). So, for atomizers, this parameter is given if spare heaters are supplied in the kit — accordingly, it is indicated for the “head” with the lowest resistance. For a battery mod, this is the smallest resistance that can be connected to it. And in starter kits, the minimum resistance is also usually indicated by the battery mod; low-resistance "heads" in such cases may or may not be included in the delivery.
Anyway, data on the minimum resistance is important in the mutual selection of an atomizer and a battery mod (including when creating custom windings) — connecting an atomizer with too low resistance is fraught with overloads and various unpleasant consequences, up to fire. However, this parameter is of particular importance for lovers of the so-called subohm — soaring at a low heater resistance (up to 1 ohm), which allows you to achieve high steam saturation (when the resistance decreases, the power increases). Not all batteries are capable of working with sub-ohm heaters, so the suitability of a battery mod for such vaping needs to be clarified.
Power
The maximum power supplied by the battery.
This is one of the main parameters of the battery pack that determines its compatibility with the atomizer. Starter kits (see "Type"), by definition, include atomizers that are optimally suited to a given battery in terms of power, and this parameter is mainly of reference value. But when choosing components separately, you should pay special attention to it. Higher
power allows you to achieve more saturated steam, but only up to certain limits — too much heating leads to a deterioration in taste, and even burning of the wick (which, all the more, does not contribute to improving the sensation of soaring). So the atomizer must normally transfer the power of the battery, otherwise, at best, you will have to constantly limit the power with the help of a varivolt or variwatt (see "Battery mod"), and at worst, normal use will be impossible at all.
Note that for classic evaporator tanks with one spiral, power up to 40 W is considered sufficient; more powerful batteries are designed mainly for advanced serviced models, drip atomizers and
bacodrips(see "Type of atomizer") that have more than one coil and, accordingly, are more high consumption in terms of energy consumption. Also note that the actual heating power depends on the voltage, and in fact it may be lower than the claimed one, depending on the resistance of the atomizer. See “Maximum voltage".
Minimum voltage
The lowest voltage that the battery mod can supply to the atomizer.
The meaning of this parameter depends on the type of battery mod and the functions of the board (see above). So, in mechanical and simple electronic modes, the smallest value to which the battery voltage can drop before it turns off and requires charging is usually indicated here. Knowing this parameter, as well as the resistance of the atomizer, you can calculate the minimum guaranteed vaping power.
If we are talking about a mod with adjustments like varivolt or variwatt, then the minimum voltage is also the lowest voltage that can be set manually in the settings. This may be necessary to reduce the power and, accordingly, the intensity of soaring — for example, if the gas station has a very rich taste, and abundant dense steam would be overkill. In adjustable battery packs, the lower the minimum voltage (with the same maximum voltage), the wider the adjustment range, the more options the vaper has to adjust the vaping parameters. See “Maximum voltage".
Maximum voltage
The highest voltage that the battery mod can supply to the atomizer.
Knowing the minimum (see above) and maximum voltage, it is possible to estimate the heating power that the battery is able to provide at a certain resistance of the atomizer. For example, if we have a battery mod with a voltage range of 3.3 – 4.8 V and an atomizer with a 1.8 Ohm coil, then the current strength at the minimum voltage will be 3.3 / 1.8 ≈ 1.8 A, and at maximum 4.8 / 1.8 ≈ 2.7 A. Accordingly, the smallest heating power will be 3.3 * 1.8 ≈ 6 W, and the largest 4.8 * 2.7 ≈ 13 W. In this case, the nominal power of the battery can be higher, but not vice versa — the actual power cannot be more than the nominal. Let's say, theoretically, the battery from our example, combined with a 0.15 Ohm sub-ohm atomizer, even at the minimum voltage, should produce a current of 3.3 / 0.15 = 22 A and a power of 3.3 * 22 = 72.6 W. However, if a power of 50 W is claimed in the characteristics, then higher values \u200b\u200bare impossible to achieve, even if you unscrew the regulator to the maximum — at low resistances, the voltage at the battery output drops sharply.
