Comparison Focusrite Scarlett Solo 3rd Gen vs Behringer U-PHORIA UM2

Connection interfaces that the audio interface is equipped with.

- USB A. Connection via standard USB port. Until recently, this was the most popular interface for external peripherals, found in almost all PCs and laptops. Nowadays, it is often replaced by a USB type C port (see the corresponding paragraph). Most USB A audio interfaces draw power directly from the PC or other host device.

- USB type B. The connector has a characteristic square shape, noticeably different from the well-known rectangular USB A ports. In audio interfaces, it is used to transmit signals from external sources to a computer for recording and processing.

- USB type C. A peripheral connector with a symmetrical contact group, which often replaces full-size USB ports on board modern PCs and laptops. Many new models of audio interfaces are being made for this interface. An exception to the rule is individual instances for Thunderbolt. For them, it is Thunderbolt that is indicated, and not USB type C.

- Thunderbolt v2. Initially, Thunderbolt is a universal connector used primarily in Apple computer equipment. On board audio interfaces it is used as a general peripheral connector (similar to USB). This uses the miniDisplayPort hardware port. The data transfer speed in this version reaches 20 Gbit/s. Recently, the v2 edition has been rep...laced by the Thunderbolt v3 version (see the corresponding paragraph).

- Thunderbolt v3. A universal interface that is found mainly in Apple technology. In audio interfaces it is used as a general peripheral connector (similar to USB). Specifically, Thunderbolt v3 provides data transfer speeds of up to 40 Gbps and uses a USB type C hardware connector (as opposed to earlier versions based on miniDisplayPort).

- Lightning. A connector used exclusively in Apple portable electronics (since 2012). Accordingly, audio interfaces with such a port are aimed at ease of connection to iPhones and iPads. Note that today there has been a transition from proprietary Lightning to the common USB type C - the latest generations of Apple gadgets are produced with just such a peripheral connection connector.

- mini-USB. A smaller version of the full-size USB interface, created for portable equipment. It is found very rarely in audio interfaces.

- FireWire. Universal connector, also known as IEEE 1394 or i-Link. In terms of functionality, it is analogous to USB, and in some characteristics it even surpasses it. However, FireWare is much less common. Used to connect to computers and some types of specialized audio equipment.

— Dante Dante connectors are used to connect audio interfaces to a network to transmit audio digitally. In this case, a standard Ethernet port (RJ-45) is used for physical access to the network.

Characteristics of the built-in DAC - a digital-to-analog converter for converting digital audio into line-level analog audio, usually in stereo format.

— Bit depth. Bit size of the digital-to-analog converter (DAC) used in the device. In this case, the meaning of this parameter is as follows: the bit depth of the DAC must be no lower than the bit depth of the audio signal with which the converter is planned to be used, otherwise the device will not be able to effectively cope with the conversion. As for specific values, the standard options in modern audio interfaces are 16 bit, 24 bit and 32 bit.

- Sampling frequency. The sampling rate of the digital-to-analog converter (DAC) installed in the audio interface. Let us recall that such a converter is responsible for converting digital audio into an analog audio signal. The paragraph usually indicates the maximum value of the sampling frequency, for which one of the standard values corresponding to a certain sound quality is used ( 48 kHz, 96 kHz, 192 kHz).

— Total audio inputs Jack / XLR. The total number of analog audio inputs such as Jack (6.35 mm) and/or XLR (this interface can be combined with a “jack”). Note that such connectors can play the role of both a line input and a microphone or instrument input. For more details, see the relevant paragraphs.

— mini-Jack. The standard 3.5 mm mini-Jack is usually used in audio interfaces as an analog (line) input for two stereo channels, as well as as a microphone audio input (see the corresponding paragraphs).

The type of line input provided in the device. Uses the line input to feed audio from an external source to the audio interface.

The following types of connectors can be used for line input:

— mini-Jack (3.5 mm). A socket for a standard mini-Jack plug (3.5 mm). The connector serves as an audio input for two stereo channels. It is designed primarily for portable electronics such as smartphones, pocket players, etc. In stationary devices, Jack (6.35 mm), XLR and RCA are more popular.

— Jack (6.35 mm). A common audio connector for transmitting an analog signal. In design, this type of socket is as similar as possible to a mini-Jack (3.5 mm), but differs in size. Jack connector (6.5 mm) provides tight contact and is less susceptible to interference. It also supports a balanced connection - high-quality transmission of audio signals over fairly long wires with effective protection against interference.

- XLR. The XLR standard is considered professional - not only because of the high quality of signal transmission, but also because of its fairly large size and the presence of locks for securely securing the plugs. However, only one channel of audio can be transmitted over one cable, so XLR outputs are usually installed in pairs - based on stereo sound. Also note that these connectors can be combined with Jack sockets (6.35 mm). They also allow y...ou to implement a connection in a balanced format with a high degree of noise immunity and the use of fairly long wires without affecting the frequency of the analog signal.

- RCA. Connector for coaxial cable with tulip type plug. The standard RCA input consists of two jacks - for stereo sound, left and right channel. One analog RCA connector can only transmit one channel of audio, so the number of such connectors corresponds to the number of channels supported by the device.

— Total audio outputs Jack / XLR. The total number of analog audio outputs such as Jack (6.35 mm) and/or XLR (this interface can be combined with a “jack”). Note that such connectors can play the role of both the Main output and the linear output. For more details, see the relevant paragraphs.

— mini-Jack. The standard 3.5 mm mini-Jack is usually used in audio interfaces as an analog (line) output for two stereo channels, as well as as an output for connecting headphones (see the corresponding paragraphs).

The type of line output provided in the audio interface design. It outputs a line-level analog audio signal. This interface is mainly used for connecting recording devices, outputting a signal to playback equipment or to an external amplifier. And the types of connectors used for linear output can be as follows:

— mini-Jack (3.5 mm). A standard socket for the popular mini-Jack plug (3.5 mm), used as a line output. This connector is mainly used to connect some models of active speakers, while two stereo channels are usually output through one mini-Jack (3.5 mm). Note that headphone outputs, which also use a mini-Jack, are considered separately - see the corresponding paragraph.

— Jack (6.35 mm). A larger analogue of the mini-Jack connector (3.5 mm) for outputting an analog stereo signal. The Jack output provides a more reliable and noise-free connection, making it ideal for professional applications. Effective protection against interference is possible with a balanced connection method. To save space, the 6.35 mm output can be combined with an XLR connector (see the corresponding paragraph). The disadvantage of this design is the impossibility of using both interfaces simultaneously. Jack line outputs (6.35 mm) adhere to the “one channel per connector” principle.

- XLR. A round three-pin connector for outputting a line-level analog audio signal, oft...en with a balanced connection type. Transmission is carried out over three wires instead of two, and during it the noise induced on the wire is eliminated. This allows the use of fairly long cables without compromising the “purity” of the signal, making this type of connection excellent for professional audio equipment. XLR is also considered a professional interface, both due to the ability to work with a balanced signal and due to increased reliability: such connectors are often equipped with locks to secure the plugs.

- RCA. Analog linear audio output using RCA connectors - so-called “tulips” (due to the characteristic shape of the plugs). The standard output of this type consists of two connectors - for the left and right stereo channels. Also note that RCA connectors can be used in other output interfaces, but they have their own names.

The number of pairs of RCA output connectors(see above) in the audio interface design. By “pair” in this context we mean two RCA connectors, usually intended for stereo audio - left (Left) and right (Right) channels.

Output connectors for connecting monitor speakers or headphones. Connecting monitors to the output of an audio interface allows musicians, sound designers, or sound engineers to monitor audio quality in real time. In audio interfaces, monitor outputs can be made in various formats, but most often there are various combinations of RCA, XLR and Jack connectors (6.35 mm), less often - the classic mini-Jack (3.5 mm).

The software included with your audio interface may vary depending on the make and model. The vast majority of it is represented by drivers, utilities for managing the device, software for recording and editing sound, virtual instruments or effects, and all kinds of plugins. It is advisable to clarify separately which specific software components are included in the audio interface package.