USA
Catalog   /   Tools & Gardening   /   Construction Power Tools   /   Staple Guns & Nailers

Comparison Stark ANG-5040 300300001 vs TOPEX 74L231

Add to comparison
Stark ANG-5040 300300001
TOPEX 74L231
Stark ANG-5040 300300001TOPEX 74L231
Outdated Product
from $49.12
Outdated Product
TOP sellers
Product typestapler (2 in 1)stapler (2 in 1)
Typepneumaticpneumatic
Fastener type
staple
nail
staple
nail
Compatible staplesBosch TK40, Prebena E, Rapid 90Bosch TK40, Prebena E, Rapid 90
Specs
Rated pressure7 bar8 bar
Operation typecontactcontact
Magazine typecassettecassette
Fasteners size
Max. staple width5.8 mm5.8 mm
Min. staple length16 mm10 mm
Max. staple length40 mm40 mm
Min. nail diameter1 mm1 mm
Max. nail diameter1.2 mm1.2 mm
Min. nail length20 mm15 mm
Max. nail length50 mm50 mm
Features
Functions
stroke force / depth adjustment
magazine indicator
 
magazine indicator
General
Dimensions240x240x55 mm
Weight1.3 kg2 kg
Added to E-Catalogseptember 2018august 2016

Rated pressure

Air pressure for which the pneumatic nailer/stapler is designed (see "Type"). It is this pressure that the compressor to which the tool is connected should give out: if the pressure is too low, the efficiency will noticeably drop, and if it is too high, it can lead to breakage and even injury.

Min. staple length

The smallest length of staples (see Fastener Type) that the stapler can work with.

The length in this case means the length of the leg — in other words, the depth to which the staple clogged "to the stop" penetrates into the material. Small staples do not require much power to drive, but the tool may not be designed for fasteners that are too short due to other parameters — for example, the design of the magazine. Therefore, for many models, this limitation is quite relevant, and in powerful professional models, the minimum length can be quite large — more than 20 mm.

Min. nail length

The shortest length of nails (see Fastener Type) that the stapler can handle.

The shorter the fastener, with the same thickness, the less effort is required to drive it, but a nail that is too short simply cannot stand under impact normally. Therefore, for many instruments, this restriction is directly indicated. It is worth paying attention to it first of all if you plan to work with small short nails.

Functions

Adjustment of impact force / depth. The ability to adjust the force of impact or the depth of clogging fasteners. These functions are implemented somewhat differently: the impact force is changed by adjusting the power supplied to the striker upon impact, and the driving depth can be set due to a mechanical limiter — for example, by retracting the striker a certain distance back, so that it simply does not was able to move beyond a certain distance. However, the purpose and use of these functions is similar: first of all, they allow you to change the depth to which the fastener is driven into the material. In addition, adjusting the force of impact (namely force) can be useful when working with delicate materials, where too powerful impacts are undesirable. Specific details of the implementation of this function should be clarified in each case separately.

Double hit. Possibility of operation of the stapler in the double impact mode. Here, this term means the ability to drive two fasteners at once in one blow — for example, for connections that require increased reliability. Note that double impact most often only works on staples, even if the tool is able to work with other types of fasteners (see above). Firstly, it is for brackets that this possibility is most relevant; secondly, it is much more difficult to implement it for nails or pins.

Bending the staple.... The ability of the stapler to work not only for driving staples, but also for bending their legs after installation. The need for bending arises in cases where the tool is used to fasten relatively thin layers of material, and the staples pierce the parts to be fastened through: bent legs provide a secure hold, and are also safer — the risk of scratching or pricking the protruding edge of the staple is minimal. Note that such work requires an anvil of hard material placed under the fastened materials; in some tools with a bending function, the anvil is part of the design, but most often it is not.

— Blade of knife. The presence of a knife blade in the design of the stapler. This feature allows you to use the tool not only for driving fasteners, but also for cutting material — for example, preparing upholstery for furniture. The blades are usually made removable (so that a dull one can be quickly replaced with a fresh one or sharpened with convenience) and have a beveled shape (this allows you to cut with the very tip of the knife, providing high accuracy and accuracy). However, this function is quite specific, therefore it is rare, and mainly among percussion models (see "Type") — only they turn out to be quite light, compact and convenient for use as knives.

— Backlight. The presence in the stapler of its own built-in flashlight, usually directed in such a way as to highlight the place of impact. This feature is extremely useful when working in low light conditions. Note that such conditions can easily arise even under normal ambient lighting: for example, the tool itself often obscures the impact site, worsening visibility and complicating accurate aiming.

— Brushless motor. Such motors do not have the classic carbon brushes found in conventional power tools, whose friction during engine operation leads to additional heating, which leads to unnecessary energy consumption and general engine wear. Refusal to use them allows you to extend the battery life of the tool, on the one hand, as well as the life of the engine, on the other.
Stark ANG-5040 300300001 often compared
TOPEX 74L231 often compared