Comparison Dnipro-M BS-614/3M vs Intertool RT-0104

Standard sizes of fasteners for which the tool is designed. This information is necessary for the correct selection of consumables: each standard dimensions corresponds to certain dimensions of parts, and sometimes also design features. There are a great many standards describing standard sizes; they differ not only in the type of fastener, but also in the geography of application and even by specific manufacturers. Detailed data on various standard sizes can be found in special sources; here we will provide general points on some of the most popular options.

First of all, it is worth saying that the standard dimensions describes only two parameters - thickness and width (for nails - size and width of the head). The length can be different: for example, for the popular staple dimensions 53, the length range can be from 4 to 14 mm, and for 140 - from 6 to 14 mm. At the same time, tools for a certain standard dimensions are not necessarily compatible with all length options. So when assessing compatibility with consumables, you should pay attention not only to this point, but also to the restrictions on the minimum and maximum length of fasteners.

This is what the list of the most popular sizes for rectangular brackets looks like:

- 55. One of the smallest sizes used in modern staplers is 6 mm wide and 1.1 mm thick.
- 90. Another relatively small standard dimensions, it has even a slightly smaller width - 5.8 mm - and a thickness in the...range of 1 - 1.27 mm.
— 57. Staples 10.6 mm wide and 1.2 mm thick.
- 59. The “thin” analogue of dimensions 57, with the same width, provides a thickness of only 0.75 mm.
— 140. Quite rigid staples with a width of 10.6 mm and a thickness of 1.24 mm.
- 114. A slightly enhanced variation of dimensions 57, with increased width and thickness - 10.8 mm and 1.4 - 1.6 mm, respectively.
- 53/53F. Quite wide (11.3 mm) staples, available in both 0.75 mm (53) and 1.25 mm (53F) thicknesses.
— 72. In fact, it’s an analogue of the 53 described above: staples 11.3 mm wide and 0.7 mm thick.
- 54/58. Wide staples 12.8 - 12.9 mm, also available in two thicknesses - 0.75 mm in version 58, 1.25 mm in version 54.

Of the semicircular staples used mainly for fastening cables, the most popular options are:

- S. Relatively small staples with a width of 6.2 mm and a thickness of 1.25.
- L. Larger dimensions - 7.7 mm wide with the same 1.25 mm thickness.

In nails for driving tools, the thickness is indicated by the size, and the width by the largest dimensions of the head. The most popular sizes these days are:

— J. Small fastening nails only 1.2 mm thick with a head width of 2 mm.
— N. Diameter 1.65 mm, cap width 2.8 mm.
- DA. The so-called finishing (finishing) nails are quite large in dimensions: size 1.8 mm, head width 3.5 mm. The head has a characteristic D-shape and, as befits finishing nails, when hammered, it is almost completely recessed into the material.

Regarding pins/studs, it is worth noting that such fasteners are actually nails without heads. Therefore, the main dimensions of such parts is thickness (size), for the most common standard sizes it is as follows:

— 40. Thin pins/studs, only 0.64 mm thick.
— 41. Larger fastener, with a size of 1.2 mm.

Detailed information on choosing a standard dimensions for specific tasks can be found in special sources.

Models of nails that the tool is compatible with.

Usually, quite specific options are indicated in this paragraph, so finding compatible consumables is not difficult. The specific dimensions of the fasteners should be specified according to the manufacturer's data — different brands use different markings.

Models of pins and/or studs that the tool is compatible with.

Usually, quite specific options are indicated in this paragraph, so finding compatible consumables is not difficult. The specific dimensions of the fasteners should be specified according to the manufacturer's data — different brands use different markings.

The number of "shots" for which the impact mechanism of the construction stapler is designed. For models with a twisted spring, it averages 10 – 12K strokes, for instances with a leaf spring — 55 – 60K operations.

The smallest thickness of nails (see "Type of fastener") that the stapler can work with.

A nail that is too thin is just as undesirable for a tool as one that is too thick: already in the store, such parts can hang out, and there is no question of correct “shooting” at all. Therefore, this limitation should definitely be taken into account when choosing, especially if you plan to work with nails of small thickness. The most "thin" modern staplers have a minimum limit of about 1 mm, and in professional models it can exceed 2.5 mm and even 3 mm.

The largest thickness of nails (see "Type of fastener") that the stapler can work with.

Thick nails require not only the appropriate size of the magazine and feeder, but also significant effort is required to drive them. Therefore, the larger the maximum allowable nail diameter, the more powerful, heavier and more expensive the tool, usually. Professional pneumatic nailers can be compatible with fasteners of 3.5 mm or more, but for entry-level tools, a thickness of 1.2 — 1.5 mm is often more than enough.

The shortest length of nails (see Fastener Type) that the stapler can handle.

The shorter the fastener, with the same thickness, the less effort is required to drive it, but a nail that is too short simply cannot stand under impact normally. Therefore, for many instruments, this restriction is directly indicated. It is worth paying attention to it first of all if you plan to work with small short nails.

The longest length of nails (see Fastener Type) that the stapler can handle.

With the same thickness, a longer nail requires not only the appropriate space in the magazine and feed mechanism, but also a higher impact energy — otherwise it simply will not work to hammer it “on the head”. This means that the maximum fastener length is directly related to the power and, accordingly, the overall level of the tool. Recall that a powerful professional tool has the appropriate dimensions and weight, moreover, it is often made pneumatic (for more details, see "Type"). Therefore, it makes sense to look for models that are compatible with long nails only if this is critical for the planned work.

The smallest diameter of the attachment pin (see Attachment Type) that the stapler can handle.

The tool cannot effectively capture a workpiece that is too thin, and, accordingly, effective clogging is out of the question. However this limitation can be so small that it can be neglected — in particular, because such thin pins for general use are simply not produced. Therefore, the minimum pin diameter is indicated relatively rarely, and mainly in cases where it exceeds 0.5 mm.