Comparison BASEUS Mini S Bracket 10000 vs Vinga BTPB3510WLRO

Battery capacity in watt-hour. These units of measurement are less popular than MilliAmp hour, but are more physically correct: they accurately describe the amount of energy accumulated by the battery. Thanks to this, in terms of capacity in Wh, it is possible to compare batteries with different rated voltages (while for mAh this is not allowed — additional calculations must be carried out using special formulas). At the same time, Wh can be converted to mAh without much difficulty if the battery voltage is known (for power banks this is in most cases 3.7 V): to do this, the capacity in Wh must be divided by the voltage and multiplied by 1000.

The number of charge-discharge cycles that the battery can withstand without significant loss of performance.

During operation, batteries wear out, and because of this, their specs (primarily capacity) noticeably deteriorate. Battery life is usually measured in charge-discharge cycles. The features of counting cycles are described in detail in special sources, but here we note that not always models with the same claimed resource turn out to be equally durable in fact. The fact is that different manufacturers may understand “significant loss of performance” differently: for example, one brand can indicate a resource up to a 20% decrease in capacity, the second — up to a 60% decrease. Therefore, when choosing, it makes sense to focus not only on pure numbers, but also on other sources — test results, reviews, etc.

Also note that battery life can be noticeably reduced if the operating conditions are violated — for example, in case of overheating or excessive cold.

The time required to fully charge a battery discharged “to zero”. Features of the charging process in different models may be different, respectively, and the time required for this may differ markedly even with the same capacity.

Fast-charging batteries tend to be more expensive. Therefore, choosing this option makes sense if you do not have much time to replenish your energy supply — for example, for hiking. However, keep in mind that charging at full speed may require a charger that supports certain fast charging technologies (see below).

It must also be said that in most modern batteries, the charging speed is uneven — it is highest at the several first percent from zero, then gradually decreases. Therefore, the time required to replenish the energy supply by a certain percentage will not be strictly proportional to the total claimed charge time; moreover, this time will depend on how much the battery is already charged at the time the procedure starts. For example, charging from 0 to 50% will take less time than from 50 to 100%, although both there and there we are talking about half the capacity.

USB type C is a popular type of USB connector characterized by its small size, reversible design, and fairly advanced (in theory) capabilities. If there are several connectors of this type, the first one is considered to be capable of delivering more power.

It is characterized by the rated power supplied by the power bank when a load is connected to the first or only USB type C output and the current strength. The speed of the charging process directly depends on the power. It is traditionally calculated by multiplying the current by the voltage; However, the standard voltage for USB power is 5 V, so current is considered to be the main indicator of power.

The magnitude of the charging current directly determines the power supplied to the device being charged - and, accordingly, the maximum speed of the process (in practice, it may be lower if the device being charged has strict restrictions on the charge current). Power is also determined by the supply voltage (the number of watts is calculated by multiplying amperes by volts); While the standard USB output voltage is 5V, many fast charging technologies (see below) use higher voltages. Therefore, in the notes to this paragraph, the maximum power on the USB type C connector is also indicated.

As for specific values, the most popular option for USB type C outputs in modern power banks is 3 A. There are also other values - both sma...ller ( 2.4 A, 2.1 A and 2 A) and larger ones - but noticeably less frequently.

A standard USB A port is characterized by the rated power supplied by the power bank when a load is connected to the first or only USB A output and the current strength. If there are several connectors of this type, the first one is considered to be capable of delivering more power.

The speed of the charging process directly depends on this indicator. Power is traditionally calculated by multiplying current by voltage; However, the standard voltage for USB power is 5 V, so current is considered to be the main indicator of power.

The charging power and, accordingly, the speed of the process depend on the current strength. Nowadays, on USB ports, a current of 2 A or 2.1 A is considered basic and quite modest, 2.4 A and 2.5 A are average, 3 A and more are noticeably above average, and certain fast charging technologies allow you to achieve values of 4 A. 4.5 A and 5 A. However, it is worth considering that to operate at high current, such an opportunity must be provided not only in the power bank, but also in the gadget being charged. So when purchasing a model, it doesn’t hurt to check whether the devices being charged suppo...rt high charge currents.

It is also worth noting two nuances associated with the presence of multiple USB charging ports. Firstly, they may differ in the current they produce. This allows you to select the optimal connector for each device: for example, to quickly charge a tablet with a capacious battery, it is desirable to have a higher current, and a device with a low charging current can be connected to a “weaker” port, so as not to create unnecessary load on the battery and controller. The second caveat is that if all USB connectors are used simultaneously, the current supplied by each of these connectors may be lower than the maximum; in other words, not all power banks allow you to simultaneously use USB ports at the maximum possible power. You can understand whether such a possibility exists by looking at the charge power (see below); if the charge power is not indicated, you should refer to detailed documentation from the manufacturer.

Nominal charge current supported by the power bank when charging its own battery via microUSB, USB type C, or Lightning (see "Battery charging inputs").

This is the maximum and, in fact, the recommended power bank charge current. If the amperes supplied by the power source exceed this value, the charge current will still be limited by the built-in controller to avoid overloading. And using a charger with a lower output current, in turn, will lead to an increase in charging time.

Data on the charge current via USB (Lightning) is especially important due to the fact that modern power banks are usually not equipped with their own chargers for these inputs, and energy sources must be separate. On the other hand, if a high charging speed is not critical for you, you can ignore this parameter: any USB connector is suitable as a power source for the corresponding power bank inputs.

Low current charging allows you to seamlessly charge devices that do not require high current. This allows you to extend the life cycle of the devices and protect them as much as possible during charging. Such devices include smartwatches, headphones, headsets, etc.

Additional functions and features provided in the design of the power bank. Such features may include, but are not limited to, an info display, a USB hub mode, a photocell for solar charging, a lighting source ( flashlight or lamp), and a shock -resistant body. Here's a more detailed description of each of these options:

— Info display. Own display installed on the power bank body. As a rule, it has a simple LCD matrix capable of displaying 2 - 3 characters and, in some cases, individual special icons. However, even such a screen provides a lot of additional information, makes it easier to manage the power bank and monitor its status.

— USB hub. Possibility of working as a USB hub (splitter). In this mode, the external battery’s own USB connectors act as USB inputs of a PC or laptop to which the power bank is connected. The connection itself, as a rule, is also carried out using the USB standard, and the battery can be charged. This function is convenient primarily because it allows you to use one USB port simultaneously to charge the power bank and connect a peripheral device (or even several). However, it does not hurt to make sure that the power supply of this port is sufficient to provide all these functions; and the charging speed may be quite slo...w. If the power bank is fully charged, it can also be useful as a classic USB hub: to increase the number of ports available for connecting peripherals, and also as a kind of remote USB extension cable (for example, if there is a free USB port only on the rear panel of the system unit, which is difficult to get to).

- Flashlight. In this case, a flashlight means a built-in light source of relatively low power, usually directional (as opposed to the lamp described below). Such a source performs an auxiliary function; it can be useful, for example, for illuminating the road at night, for short-term illumination in a dark room (basement, cellar), etc.

- Lamp. Built-in light source, usually in the form of an oblong panel of several LEDs; such a panel can be made folding. Unlike flashlights (see above), lamps provide not directional, but diffused light, which has a shorter range, but covers a larger space. Such lighting can be useful, for example, for reading, for illuminating a room during a power outage, and even for creating a certain atmosphere.

- Shock protection. Enhanced protection against impacts and shocks. The specific degree of such protection may vary; it should be clarified according to the official characteristics; however, most models in this category are capable of at least transferring a fall from a height of about 1 - 1.2 m onto a flat hard surface without consequences. Well, in any case, such devices will be more resistant to mechanical stress than conventional ones. It is also worth noting that shock protection in modern power banks is most often combined with protection from dust and moisture (see above), although there are exceptions to this rule.

— Charging from the sun. Possibility of charging the power bank from the sun or other bright light source. To do this, a corresponding device is installed in the body - a solar battery (photocell). This function can be especially useful during a long stay away from civilization - for example, on a hike. And although the efficiency of solar panels in general is not very high, when exposed to bright light for a long time, you can accumulate quite a lot of energy.

The power bank has its own stand for a smartphone. Usually, this is a retractable or folding device, on which the smartphone can be installed almost vertically (with a slight inclination); at the same time, the back side of the smartphone will rely on the power bank itself, and the stand will prevent the gadget from leaning forward.

This feature can be useful, for example, for watching movies — including while charging the device. At the same time, it is worth noting that we are talking specifically about smartphones — usually, it is impossible to install a tablet or even a phablet on such a stand.