Comparison Navin Camellia E L 480x800 12-007130-4880 vs LARIS Mix E 480x500/5

The design of the towel rail determines primarily its appearance, but can affect more practical aspects - for example, the installation features. The most popular modern designs include serpents (incl. M-shaped and P-shaped a/href and" (including volumetric), protrusions in the direction of, and angular constructions. In addition, there are original designer solutions. They are all described below.

— P-shaped coil. Type of coils described above, in which the main (leading) pipes are bent in the form of the letter «P». Most often, between the «legs» of this letter there is an additional coil from pipes of a smaller diameter - thus, with small dimensions the towel rail provides many «seats». However, there are also maximally simple models, without additional coil.

— M-shaped coil. Coils (see above), in shape resembling the letter M, laid to the side. In essence, it is a version of the classical S-shaped coils, having three bends: two to one side and one, between them, to the other.

— Ladder. The design of such towel rail is based on two vertical elements (tubes or bars), between which are located horizontal jumpers-crossbars, on the manner of steps of the usual stairs (hence the name). Modern models - «ladders» are very diverse, ca...n have different width and height, differ in the number of crossbars, equipped with additional shelves for drying (more about all this see below), etc. At the same time, the price of such devices is quite low. Of the drawbacks of the ladder it is worth noting that the towel hung on this design is likely to close several bars under itself - this makes it difficult to simultaneously dry several towels (although it increases the speed of the process by contacting the tissue at once with several heated bars).

— Volumetric ladder. Type of ladder (cf. above), in which the jumpers are not located directly between the vertical tubes, but are displaced relative to them forward and/or backward. The simplest variant of the three-dimensional ladder is one row of crossbars moved forward; this slightly increases their useful length at the same width of the entire structure, but on this the key differences with the normal ladder end. There are more complicated variants, with the arrangement of the jumpers in two vertical rows - for example, one row is directly between the tubes, and the other is forward or one is offset forward and the other is backward. These towel warmers are very useful if you need to dry several towels at the same time, but they are usually quite expensive.

— Side protrusions. This design can be called «one-way ladder»: it also combines vertical elements and horizontal jumpers, but the jumpers are fastened only on one side - the second is located «on weight». This gives the towel warmer an original look. However, in water models of this design is quite difficult to ensure efficient water circulation, so the «protruding» design did not get widespread.

— Corner. As the name suggests, models of this type were originally designed to be installed in the corner of the bathroom. This requires appropriate design features; they can be different in different models. Note that there are options for both «normal», internal angle, and external, protruding.

— Designer. This category includes all towel warmers with original appearance and not belonging to any of the above categories. An indispensable element of their design is only the presence of horizontal jumpers (so that, actually, there was where to hang towels), but the options for their mutual arrangement, connecting each other and with a support, etc. are limited only by the imagination of designers.

The maximum power consumed when operating an electric towel rail (or combined model when operating from an electrical grid; see «Type»). As a rule, this value corresponds to the operating thermal capacity of the electric heater, so that it is possible to estimate the overall efficiency of such devices from the power consumption. In addition, energy consumption and network load depend on this indicator.

As a rule, manufacturers select the power consumption depending on the size of the towel bar - to ensure it is sufficient for heating and effective drying. This requires relatively little energy. But in the role of a heater for the bathroom is more convenient to use water heaters - they are easier to achieve high power (and such heating is cheaper). Therefore, electric heaters in modern models have low power - the devices more than 150 W are rare, and the most low-power devices do not reach and 50 W.

The highest operating temperature of the towel bar. The features of this parameter depend on the type of device (see above). For water models, the maximum water temperature (or other coolant) is specified here, at which the device can be guaranteed to operate indefinitely for a long time without risk of damage. Usually this value is not less than 95 °C, and in some models may exceed the boiling point of the water and reach 105...110 C. This is usually more than enough for rooms with central heating and hot water supply, but if the heating is provided autonomously, It is necessary to specify separately the range of operating temperatures in the contours and make sure that the selected towel rail will fit them.

In the case of an electrical model, maximum operating temperature means the highest temperature to which the device can heat up. Usually, when it is achieved, the heating is automatically switched off and turned on only when the temperature is significantly lower. In this case, the usual values are 60...70°C, which is comparable to the standard water temperature in the district hot water supply systems - this temperature ensures efficient drying and at the same time does not create a risk of being burned by accidental touch.

The location of the cable on the towel rail housing allows you to choose the right model, so as not to invent with the connection of the device to the socket.

— Left. The electrical wire is placed on left side of the body, which allows a neat and concise installation of the towel rail on the wall, on the right side of the plug.

— Right. The power cable is removed via right side of the housing. This wiring arrangement is advisable to choose when the towel rail will be mounted to the left of the outlet.

— Hidden. Hidden cable liner involves connecting to the power grid behind the false wall or by means of electrical communications hidden in the wall. In this case, the heater terminal box itself is most often placed closer to the center of the housing. As a rule, the towel rail with the option of a hidden connection has a short wire without a plug at the end. But there are models that are not normally equipped with a connecting wiring - in this case, it is necessary to connect the end of the cable hidden in the wall to the terminal box heater. Also on the market there are models that support both connection options: both hidden and classic (using a conventional power plug), which allows the user to determine which option will be the best for him.

Number of jumpers - horizontal elements - provided in the design of the towel rail. It is on them are placed towels and other things designed to dry; however, there are models in which not every jumper is suitable for this. The fact is that horizontal elements can be placed in groups, inside which the distance between them is so small that it is very difficult, if not impossible, to place a towel there. In such groups, only the upper bridge supports, and the rest play the role of additional heating elements, increasing the heating area and, accordingly, the efficiency of drying the fabric. This feature is quite common in models with more than 10 jumpers.

It can be said that, in theory, the more jumpers - the more things can be hung on the towel rail; however, in practice, this moment largely depends on the design of a particular model, And the more horizontal elements there are, the more likely they are to be grouped. Also, it is worth paying attention to the width of the towel rail, according to this criterion you can conventionally divide them into broad and narrow.