Comparison Silverlit 360 Cross 1:18 vs Silverlit 360 Tornado 1:18

The scale allows you to estimate the overall dimensions of the model — it describes the ratio of its dimensions to the dimensions of a full-size machine of a similar type (see below). For example, the length and width of a full-sized buggy average about 4 m and 2 m, respectively; this means that for a radio-controlled model on a scale of 1:10, these parameters will be 10 times smaller — about 40 cm and 20 cm (plus or minus).

Miniature scales are considered to be 1:24 or less ( 1:28 and 1:32), while in the largest scales it reaches 1:6( 1:5) — such models are not much smaller than children's cars (however, they are not intended to replace them). A small size is considered optimal for use in residential areas, a large one — in open areas. Most road models (see 'Type') are available in 1:10 scale, SUVs in 1:8, and larger scales are found in advanced internal combustion engine models (see 'Engine'). The most common scale options are 1:14, 1:16 and 1:18, which are found in both the low-cost and high-end segments.

The highest speed that the machine can develop. Usually, this parameter is indicated for certain "perfect conditions": a flat track, high-quality fuel or a full battery charge (depending on the type of engine, see above), etc. Real figures tend to be somewhat lower; however, different models can be compared with each other according to this characteristic.

High maximum speed is important primarily for "racing" cars (ring and short-course, see above); in stunt and drift models, it does not play a decisive role. Also, you should pay attention to the maximum speed values when buying an amateur model for entertainment — here you need to take into account the features of its application. For example, if the machine is intended for a 3-4 year old child as a toy in an apartment, high speed will not be an advantage, but a disadvantage (especially since the cost of the “apparatus” directly depends on its speed).

The type of power source used in a machine with an electric motor (see “Motor”).

- AA. Replaceable elements of a standard size, popularly known as “pen-light batteries”. The main advantage of battery-powered cars over battery-powered cars is the ability to quickly replace dead batteries. On the other hand, the power of such power supply is quite modest, so they are found mainly in models for younger people.

- AAA. Such elements are almost completely similar to the AA described above and outwardly differ from them only in their reduced size (which is reflected in their common name - “little finger”).

- Ni-Mh. Specialized batteries made using nickel-metal hydride technology like other batteries ( Li-Pol, Li-Ion, Ni-Cd, LiFePO4, branded) are superior to replacement batteries in capacity and compactness and are better suited for powerful electric motors. Ni-Mh batteries themselves are notable primarily for their ability to withstand high charge and discharge currents without consequences - the first is important given the “gluttony” of electric motors, the second has a positive effect on the charging speed. In addition, such batteries are resistant to low temperatures, do not h...ave a “memory effect”, and are relatively inexpensive. At the same time, they are inferior to Li-Pol elements in terms of capacity (with the same dimensions).

- Li-Pol. Specialized batteries made using lithium-polymer technology. For more information on specialized batteries in general, see above (Ni-Mh). Li-Pol technology itself makes it possible to create batteries with high capacity, small size and weight, and without the “memory effect,” however, it is quite expensive.

- Ni-Cd. A relatively old battery manufacturing technology, the predecessor of the Ni-Mh described above. The common features of these technologies are resistance to high charge and discharge currents, low temperatures, and low cost. True, nickel-cadmium batteries are subject to the “memory effect” - a decrease in capacity when charging an incompletely discharged battery; however, this can be corrected by using advanced chargers and following operating instructions. But the clear disadvantage of this option is considered to be environmental unsafety during production and disposal; This is typical for all batteries, but it is most relevant for Ni-Cd cells, so they are used less and less.

— Li-Ion. Batteries made using lithium-ion technology and not belonging to any of the universal standard sizes (like AA). Lithium-ion batteries are practically not subject to the “memory effect”, are easy to use and charge fairly quickly. Their disadvantages include a higher price and less resistance to high and low temperatures.

— LiFePO4. Lithium iron phosphate batteries are actually a modification of lithium-ion batteries (see the corresponding paragraph), developed to eliminate some of the shortcomings of the original technology. They are notable above all for their high reliability and safety: the likelihood of a battery “exploding” when overloaded is reduced to almost zero, and in general LiFePO4 can cope with high peak loads without any problems. In addition, they are quite resistant to cold and maintain operating voltage almost until discharge. The main disadvantage of this type is its slightly smaller capacity.

— Branded battery. This category includes all specialized batteries (see subparagraph “Ni-Mh” above), for which the manufacturer did not indicate the manufacturing technology. We also note that if “ordinary” specialized batteries can be standard and can be used in different models of radio-controlled equipment, then branded batteries often have an original design and are designed only for cars from one manufacturer.

The number of batteries (namely AA or AAA batteries) required to operate the car.

The frequency at which the transmitter of the model control box operates.

— 27.145 MHz. One of the frequencies used for radio remote control for a long time; in some CIS countries it is even reserved by state regulatory bodies for this very purpose. Such transmitters are relatively inexpensive, but suffer from one serious drawback: they do not provide channel separation when several consoles are operating in close proximity to each other. In other words, if the machine stays in the coverage area of two transmitters, the signals from them will be mixed, which is actually tantamount to a loss of control. This is most often unimportant for recreational models, however, in competitions with several cars on the track at the same time, it can create serious problems and requires tricks with the design of the frequency grid and the use of interchangeable crystal oscillators. As a result, in professional motorsport, this frequency is gradually being replaced by the more advanced 2.4 GHz standard.

Separately, we note that among car models there may be transmitters with frequencies of 35, 40 and 75 MHz; according to the main features, they are completely similar to the described 27.145 MHz and differ only in the operating frequency.

— 2.4 GHz. The most advanced communication standard to date, used by remote control cars. Its main feature (and difference from those described above) is the possibility of normal operation of several transmitters of this...format in close proximity to each other. To do this, various technologies are used that provide automatic distribution of receiver-transmitter pairs over their own channels (similar to how it happens, for example, in mobile communications). Theoretically, the 2.4 GHz band may be more prone to interference, as many modern electronics work in it (in particular, Wi-Fi and Bluetooth modules); however, due to the aforementioned distribution of channels, such problems arise only in very unfortunate cases.