Comparison Bosch PBS 75 A 06032A1020 vs Makita 9910

The power consumed by the grinder during operation. Usually more than the output (useful) power (see above) due to losses during the conversion of energy from electrical to mechanical. However, the general patterns in this case are the same: a more powerful tool, on the one hand, is usually more performant, on the other hand, it is heavier, larger and more expensive. In addition, the total electricity consumption depends on this indicator; however, grinders, even the most powerful ones, consume relatively little energy, and difficulties can arise only when connecting a high-performance professional tool to weak electrical wiring.

Note that it is much easier to determine the consumed power than the useful one; therefore, only this parameter is often indicated in the characteristics, without specifying the useful power. In general, it is quite possible to compare grinders of the same type using it (see above): a modern tool has approximately the same efficiency, and in most cases the useful power values bare related in the same way as the consumed values.

Belt speed provided by the grinder. For more information about belt units, see "Type". In this paragraph, both one value and a range can be given — if the device has a speed control (see "Additionally — Speed regulator").

Other things being equal (primarily the same belt width), a higher speed has a positive effect on productivity. On the other hand, to ensure such a speed, a more powerful engine is needed, which accordingly affects the weight, price and energy consumption of the entire tool. In addition, the low belt speed contributes to accuracy: the chance of removing excess material is reduced. So it’s definitely worth looking specifically for a “fast” grinder only if it is to be used often and for large volumes of work. In other cases, a slower model may well be the best option. More detailed recommendations on this matter (including for different materials and types of work) can be found in special sources.

The length of the belt or sheet for which the grinder is designed.

Working nozzles in the form of sheets are used in units with a vibrational principle of operation, in the form of tapes — respectively, in tape ones (for more details on both, see "Type"). Anyway, this paragraph does not indicate the working length of the tape / sheet (that is, the length of the surface adjacent to the material being processed), but the total — that is, the size of the nozzle itself. This size in itself determines only the compatibility of the grinder with certain sheets / tapes. At the same time, clamp-like fastenings (see "Sheet fastening"), used in most classic vibrating instruments, often allow you to install sheets of slightly longer lengths than indicated in the specifications. Hook-and-loop models (mostly delta sanders) technically accept both longer and shorter sheets, although in fact this is not recommended at best. But in tape tools, the length of the tape must exactly match the parameter specified in this paragraph — even a slight deviation can lead to incompatibility.

As for the working length of the tape / sheet, it inevitably turns out to be less than the total (for sheets — not much, for tapes — quite significantly). However a longer tape/sheet often has a greater working length; however, with the same general dimensions of the nozzle, its working size in different tools may be different; it is indicated in the item "Sole Size" (see below).

The width of the belt or sheet for which the grinder is designed.

Working nozzles in the form of sheets are used in units with a vibrational principle of operation, in the form of tapes — respectively, in tape ones (for more details on both, see "Type"). Anyway, this paragraph does not indicate the working width of the tape / sheet (that is, the width of the surface adjacent to the material being processed), but the total — that is, the size of the nozzle itself. This size in itself determines only the compatibility of the grinder with certain sheets / tapes. At the same time, clamp-like fasteners (see “Sheet fastening”), used in most classic vibrating instruments, usually fix the sheet only in front and behind, so that in such instruments the restrictions on width are not as strict as, for example, on length: the sheet may be somewhat wider, and somewhat narrower than the nominal size. However, such possibilities should be clarified separately, and for a full guarantee it is better to clarify whether a particular machine allows deviations in width. The situation is similar with delta sanders, where Hook-and-loop is traditionally used: a discrepancy in width technically does not prevent the installation of a nozzle, but not all models allow this. As for the band tools, they may allow the installation of a narrower band — but not a wider one.

As for the working width, it, usually, corresponds to the general one, or (in some vibration models) differs slightl...y from it. Anyway, the working width is given under Sole Size (see below).

The size of the sole provided in the tool.

This parameter is indicated for two types of grinders — most models with a vibrational principle of operation (namely, for vibration and delta grinders, as well as multifunctional ones), as well as belt units. For more information about both, see "Type", here we note that the sole as such is only available in vibrating tools — in tape tools, we are talking about the size of the section of the tape that is in direct contact with the material. Simply put, the size of the sole is the size of the working surface of the machine.

The larger the size of this surface, the more performant the machine, the better it is suitable for large volumes of work. And tape models, we recall, are used mainly for processing oblong parts and during operation they are usually located across such a part; so that for such machines it is highly desirable that the length of the tape be not less than the width of the surface to be treated — otherwise, accurate processing can be quite difficult. On the other hand, a large sole inevitably affects the dimensions, weight, and most often the cost of the tool, besides, it can make it difficult to use in cramped conditions. Yes, and consumables for such soles (sheets, tapes) require larger ones — and, accordingly, more expensive. So when choosing according to this indicator, it is worth considering the features of the intended application; if you wish, you can refer to special sources for detailed r...ecommendations on this matter.

Also note that for multifunctional models (see "Type") in this paragraph, several options are most often given — for each specific sole. However, there are models where only one set of sizes is indicated. This can either mean that both main vibration nozzles (rectangular and triangular) have the same dimensions in length and width — or that the data is indicated for a non-removable triangular sole, on which a larger rectangular one is put on if necessary. Such details can often be clarified directly from the photographs of the goods, in extreme cases — from the manufacturer's documentation.

— Additional handle. Separate handle for a second hand. Theoretically, such equipment could make the instrument more comfortable to hold with two hands. However, in fact, the absence of an additional handle is often not critical: many tools without it are either intended to be held in one hand (like some straight grinders, see "Type"), or have other adaptations for a second hand (for example, a ledge on the body). So to answer the question of whether you need an additional handle, you need to take into account the type and size of the grinder, as well as the features of the planned work. Also note that by default such a handle is designed for right-handers, and the possibility of its use with left-handed holding should be specified separately.

— Charger(charger). A device for charging the battery in a grinder with the appropriate type of power supply (see "Power supply"). Also in this paragraph, a specific model of the charger is usually specified. In itself, the presence of a "charger" in the kit eliminates the need to look for and buy it separately; at the same time, such a charger is optimally suited to at least the “native” battery, and often also to other compatible batteries. And data on the model will be useful, first of all, in case the complete charger is lost or fails and you have to buy the same or similar one instead. In addition, knowing the charger model, you can find detailed data abo...ut it and evaluate its characteristics and features (compatibility with various batteries, additional functions, etc.). At the same time , the “without charger” package is also very popular — see below for more on it.

— No charger. This feature is indicated exclusively for battery models (cars with other types of power supply — see "Power Source" — by definition do not have a charger, there is no need to specify this point for them). The meaning of this configuration is that modern grinders most often use standard batteries, which are also suitable for other power tools of the same brand and are designed, respectively, for standard “chargers”. Thus, if the "household" already has a battery tool, then the charger for it may be suitable for the grinder, you will not need to overpay for the second copy of the charger. And even if the charger is not available, usually, it can be purchased separately without much difficulty (moreover, some tools also allow you to choose the most suitable model of such a device from several options).

— Case / bag included. The presence of a case or bag for storing and transporting the tool. The case is a suitcase and is made of durable material, usually there is a place not only for the machine itself, but also for working attachments and other additional accessories. The bag is soft, which allows it to be compactly folded when there is no need for it. Check the availability of a case or bag immediately before buying.

— Dust collector. Container for collecting dust and other contaminants that occur during operation. See "Advanced — Connecting the dust box" for details.

— Barbell. A long rod significantly expands the "radius" of the tool: with such equipment, you can reach a great height, process a large area without rearranging the platform or other stand, etc. Such features are relevant primarily when processing walls, so the vast majority of grinders with rods in the kit are wall grinders(see "Type").

Approximate noise level generated by the grinder during operation. Note that this indicator is quite approximate, because. actual "loudness" can vary markedly depending on the type and shape of the material being processed, the surface it is placed on, and other circumstances. In addition, different manufacturers may use different measurement methods. Nevertheless, this indicator makes it possible to assess how comfortable this or that model is in operation and whether special hearing protection is required.

The most “quiet” modern grinders give out about 65 dB — this is comparable to loud speech at a distance of 1 m; in the loudest, the noise level reaches 107 dB — this is the volume of an industrial workshop.

The length of the network cable can tell you how far from the outlet you can operate the device. Therefore, for domestic use, it is more relevant to choose models with a short cord, for construction work or use in production, in the garage a longer cable is better.

The total weight of the grinder; for battery models (see "Power Source"), usually, it is indicated without taking into account the battery.

This indicator has two meanings. On the one hand, light weight has a positive effect on manoeuvrability and reduces fatigue during work — especially when processing vertical surfaces and ceilings, as well as in other situations where the tool has to be held on weight. On the other hand, for grinders with a vibrational principle of operation (see "Type"), used for processing horizontal surfaces, a significant weight is considered optimal: it allows the tool to fit closer to the material being processed, and also contributes to stability and retention. So when choosing such a model by weight, it is worth considering the features of its intended application.