Comparison Dnipro-M PE-50S vs Dnipro-M PE-45S

The power consumed by the grinder during operation. Usually more than the output (useful) power (see above) due to losses during the conversion of energy from electrical to mechanical. However, the general patterns in this case are the same: a more powerful tool, on the one hand, is usually more performant, on the other hand, it is heavier, larger and more expensive. In addition, the total electricity consumption depends on this indicator; however, grinders, even the most powerful ones, consume relatively little energy, and difficulties can arise only when connecting a high-performance professional tool to weak electrical wiring.

Note that it is much easier to determine the consumed power than the useful one; therefore, only this parameter is often indicated in the characteristics, without specifying the useful power. In general, it is quite possible to compare grinders of the same type using it (see above): a modern tool has approximately the same efficiency, and in most cases the useful power values bare related in the same way as the consumed values.

The speed of rotation of the working attachment, which is capable of providing a grinder of the appropriate design (for example, angle — see "Type"). If the device has speed control, this paragraph shows the range of such adjustment, from minimum to maximum.

It makes sense to compare by this parameter units belonging to the same type and having the same maximum diameter of the disk (or other working nozzle). The latter is due to the fact that the larger the disk, the faster its edge moves (at the same speed); i.e. a larger diameter requires less RPM for the same performance/efficiency. In general, when comparing different models, the following should be taken into account. The higher rotation speed is well suited for large volumes of work (because it improves productivity) as well as for fine polishing with “delicate” nozzles. A lower setting, in turn, improves accuracy (reduces the chance of removing excess material), as well as provides more torque and allows you to more effectively deal with hard, stubborn materials. More detailed recommendations for different types of work and different nozzle diameters can be found in special sources; here we note that an increase in the rotation speed, usually, affects the cost of the machine compared to analogues (since this requires a more powerful engine). In addition, discs and other attachments may have maximum RPM limits.

The frequency of vibration of the working attachment, which is capable of providing a grinder of the appropriate design (a classic example is vibration, see "Type"). If the device has an oscillation frequency adjustment, this paragraph gives the range of such adjustment, from minimum to maximum.

A higher frequency (with the same amplitude — see below) improves overall performance, especially when working with hard, stubborn materials, and also contributes to efficiency in delicate finishing (such as polishing). In turn, a lower frequency reduces the likelihood of making a mistake by removing an excessive amount of material. There are also more specific points related to this parameter; them, as well as recommendations for choosing the frequency for different jobs, materials and types of sanding sheets, can be found in special sources. Here, we note that individual sanding sheets may have their own limitations or recommendations regarding the operating frequency.

The amplitude of oscillations made during the operation of the nozzle of an eccentric, vibration or delta grinding type machine (see above). Along with the frequency (see above), it is one of the most important indicators of such machines. Higher amplitude provides more intensive processing, which has a positive effect on performance; on the other hand, for delicate work, it is desirable to have a small oscillation amplitude(less than 2 mm).

The length of the network cable can tell you how far from the outlet you can operate the device. Therefore, for domestic use, it is more relevant to choose models with a short cord, for construction work or use in production, in the garage a longer cable is better.

The total weight of the grinder; for battery models (see "Power Source"), usually, it is indicated without taking into account the battery.

This indicator has two meanings. On the one hand, light weight has a positive effect on manoeuvrability and reduces fatigue during work — especially when processing vertical surfaces and ceilings, as well as in other situations where the tool has to be held on weight. On the other hand, for grinders with a vibrational principle of operation (see "Type"), used for processing horizontal surfaces, a significant weight is considered optimal: it allows the tool to fit closer to the material being processed, and also contributes to stability and retention. So when choosing such a model by weight, it is worth considering the features of its intended application.